Resource potential mapping of bifacial photovoltaic systems in India
Ontology highlight
ABSTRACT:
SUBMITTER: Johnson J
PROVIDER: S-EPMC10565778 | biostudies-literature | 2023 Sep
REPOSITORIES: biostudies-literature
Similar Datasets
Project description:Accurate modeling of bifacial illumination is critical to improve the prediction of the energy yield of bifacial solar systems. Monte Carlo ray tracing is the most powerful tool to accomplish this task. In this work, we accelerate Monte Carlo ray tracing of large solar systems by nearly 90%. Our model achieves root-mean-square error values of 7.9% and 37.2% for the front and rear irradiance compared against single-axis tracking field reference data, respectively. The rear irradiance modeling error decreases to 18.9% if suspected snow periods are excluded. Crucially, our full system simulations show that surrounding ground surfaces affect the rear irradiance deep into the system. Therefore, unit system simulations cannot necessarily ignore the influence of the perimeter of large installations to accurately estimate annual yield. Large-scale simulations involving high-performance supercomputing were necessary to investigate these effects accurately, calibrate our simplified models, and validate our results against experimental measurements.
| S-EPMC8760442 | biostudies-literature
Project description:The development of a highly efficient multijunction technology is a key challenge for the future of photovoltaic and for the transition to more renewable energy sources. In this scenario, four-terminal architecture (4T) compared to the classic tandem design allows a large intrinsic robustness to the variations of the solar spectrum, which continuously occur under normal outdoor operation conditions. On the other hand, bifacial solar cells and modules have already proven to be able to increase the energy yield of solar farms at reduced costs. For these reasons, a thorough investigation of the compatibility between these two solutions has been performed by combining a III-V semiconductor with the silicon heterojunction technology in a four-terminal device. This work has been designed in support of the research article entitled "Outdoor performance of GaAs/Bifacial Si Heterojunction four-terminal system using optical spectrum splitting" [1], which showed, through data modeling and an accurate daily analysis of the spectral distribution of solar light, how a four-terminal architecture guarantees the consistency of the bifacial gain and more robust performances than a two-terminal system. Here additional data on the manufacturing, optimization and characterization of the device are presented.
| S-EPMC9679458 | biostudies-literature
Project description:Energy recovery from renewable sources is a very attractive, and sometimes, challenging issue. To recover solar energy, the production of photovoltaic (PV) modules becomes a prosperous industrial certainty. An important material in PV modules production and correct functioning is the encapsulant material and it must have a good performance and durability. In this work, accurate characterizations of performance and durability, in terms of photo- and thermo-oxidation resistance, of encapsulants based on PolyEthylene Vinyl Acetate (EVA) and PolyOlefin Elastomer (POE), containing appropriate additives, before (pre-) and after (post-) lamination process have been carried out. To simulate industrial lamination processing conditions, both EVApre-lam and POEpre-lam sheets have been subjected to prolonged thermal treatment upon high pressure. To carry out an accurate characterization, differential scanning calorimetry, rheological and mechanical analysis, FTIR and UV-visible spectroscopy analyses have been performed on pre- and post-laminated EVA and POE. The durability, in terms of photo- and thermo-oxidation resistance, of pre-laminated and post-laminated EVA and POE sheets has been evaluated upon UVB exposure and prolonged thermal treatment, and the progress of degradation has been monitored by spectroscopy analysis. All obtained results agree that the lamination process has a beneficial effect on 3D-structuration of both EVA and POE sheets, and after lamination, the POE shows enhanced rigidity and appropriate ductility. Finally, although both EVA and POE can be considered good candidates as encapsulants for bifacial PV modules, it seems that the POE sheets show a better resistance to oxidation than the EVA sheets.
| S-EPMC8914825 | biostudies-literature
Project description:Omnidirectional photosensing is crucial in optoelectronic devices, enabling a wide field of view (wFoV) and leveraging potential applications for the Internet of Things in sensors, light fidelity, and photocommunication. The wFoV helps overcome the limitations of line-of-sight communication, and transparent photodetection becomes highly desirable as it enables the capture of optical information from various angles. Therefore, developing a photoelectric device with a 360° wFoV, ultra sensitivity to photons, power generation, and transparency is of utmost importance. This study utilizes a heterojunction of van der Waals SnS with Ga2 O3 to fabricate a transparent photovoltaic (TPV) device showing a 360° wFoV with bifacial onsite power production. SnS/Ga2 O3 heterojunction preparation consists of magnetron sputtering and is free from nanopatterning/nanostructuring to achieve the desired wFoV window device. The device exhibits a high average visible transmittance of 56%, generates identical power from bifacial illumination, and broadband fast photoresponse. Careful analysis of the device shows an ultra-sensitive photoinduced defect-modulated heterojunction and photocapacitance, revealed by the impedance spectroscopy, suggesting photon-flux driven charge diffusion. Leveraging the wFoV operation, the TPV embedded visual and speech photocommunication prototype demonstrated, aiming to help visually and auditory impaired individuals, promising an environmental-friendly sustainable future.
| S-EPMC10870018 | biostudies-literature
Project description:Environment-friendly flexible Cu2ZnSn(S,Se)4 (CZTSSe) solar cells show great potentials for indoor photovoltaic market. Indoor lighting is weak and multi-directional, thus the researches of photovoltaic device structures, techniques and performances face new challenges. Here, we design symmetrical bifacial CZTSSe solar cells on flexible Mo-foil substrate to efficiently harvest the indoor energy. Such devices are fabricated by double-sided deposition techniques to ensure bifacial consistency and save cost. We report 9.3% and 9% efficiencies for the front and back sides of the flexible CZTSSe solar cell under the standard sun light. Considering the indoor environment, we verify weak-light response performance of the devices under LED illumination and flexibility properties after thousands of bending. Bifacial CZTSSe solar cells in parallel achieve the superposition of double-sided output current from multi-directional light, significantly enhancing the area utilization rate. The present results and methods are expected to expand indoor photovoltaic applications.
| S-EPMC8149396 | biostudies-literature
Project description:Recently, the wafers used in solar cells have been increasing in size, leading to larger module sizes and weights. The increased weight can cause deflection of photovoltaic (PV) module, which may lead to decreased cell efficiency. In this study, we developed a deep neural network (DNN)-based finite element (FE) surrogate model to obtain the optimal frame design factors that can improve deflection in large-scale bifacial PV module. Initially, an FE model was constructed for large-scale bifacial PV module. Based on this, the FE surrogate model was trained using 243 FEA datasets generated within the proposed range of factors. Furthermore, it was improved through Bayesian optimization and k-fold validation. As a result, the final loss value was 3.743×10-4 , and the average mean absolute percentage error (MAPE) and coefficient of determination ( R2 ) values for deflection and weight were 0.0017, 0.9972 for the training set, and 0.0020, 0.9962 for the test set, respectively. This indicates that the trained FE surrogate model possesses significant accuracy. After generating 1 million datasets within the range of frame design factors, the trained model was used to obtain predictions. Based on this data, the frame design factors that minimize both deflection and weight were identified as about a = 1.5, b = 13.7, c = 1.5, d = 3.0, e = 4.3. At this point, the deflection was 11.1 mm, and the weight was 3.6 kg. After altering the frame shape with the derived factors, FEA was conducted. The results matched for both deflection and weight, with almost no error. At this point, the weight increased by approximately 12.8% compared to the existing, while the deflection decreased by about 9.6%. Additionally, we analyzed the relationship between deflection and weight for each factor and secured the basis for the derived results. Consequently, our FE surrogate model accurately predicted the FEA results and quickly identified the optimal factors that minimize deflection and weight.
| S-EPMC11199489 | biostudies-literature
Project description:Abstract Glass/glass (G/G) photovoltaic modules are quickly rising in popularity, but the durability of modern G/G packaging has not yet been established. In this work, we examine the interfacial degradation modes in G/G and glass/transparent backsheet modules under damp heat (DH) with and without system bias voltage, comparing emerging polyolefin elastomer (POE) and industry‐standard poly(ethylene‐co‐vinyl acetate) (EVA) encapsulants. We investigate the transport of ionic species at cell/encapsulant interfaces, demonstrating that POE limits both sodium and silver ion migration compared with EVA. Changes to the chemical structures of the encapsulants at the cell/encapsulant interfaces demonstrate that both POE and EVA are more susceptible to degradation in modules with a transparent backsheet than in the G/G configuration. Adhesion testing reveals that POE and EVA have comparable critical debond energies after the DH exposures regardless of system bias polarity. The results of this study indicate that the interfacial degradation mechanisms of G/G appear to be similar to those of conventional glass/backsheet modules. For emerging materials, our results demonstrate that POE offers advantages over EVA but that transparent backsheets may accelerate encapsulant degradation due to increased moisture ingress when compared with the G/G structure. G/G modules with POE were found to be more durable than those with EVA or transparent backsheet. The high resistivity POE inhibits sodium migration through the interfaces under negative and silver migration under positive bias, decreasing risk of PIDs and transmittance loss as compared to EVA. Interfacial adhesion strength reduced for both EVA and POE encapsulants resulting in similar risks of delamination under the damp heat conditions.
| S-EPMC9796659 | biostudies-literature
Project description:The bi-facial photovoltaic sunshade (BiPVS) is an innovative solution that utilizes vertically mounted bi-facial photovoltaic modules to provide shading. The BiPVS is capable of converting incident solar radiation into electricity on both the front and rear sides of the module, resulting in higher electrical efficiency compared to traditional mono-facial PV sunshades. The BiPVS has great potential as a sustainable solution for building shading and energy generation, which allows for improved indoor light/thermal environment and building energy efficiency. In this study, the bi-facial photovoltaic sunshade (BiPVS) was implemented in an office under typical hot summer and warm winter climate of Shenzhen, China. The energy performance of the BiPVS was analyzed using Energyplus. The comprehensive building energy saving was evaluated by comparing the energy consumption of the office with and without the BiPVS. Results showed that the total annual photovoltaic power generation was 133.19 kWh, while the comprehensive building energy savings were 159.65 kWh. Additionally, carbon dioxide emissions were reduced by 83.29 kgCO2 per year. The proposed method can help optimize the design parameters of BiPVS according to specific climate conditions, building types, and orientation, and contribute to the development of high-efficiency BIPV technology and support efforts towards carbon neutrality.
| S-EPMC10405007 | biostudies-literature
Project description:Cloud and aerosol are two important modulators that influence the solar radiation reaching the earth's surface. It is intriguing to find diverse impacts of clouds and aerosols over Southern China (SC) and Northern India (NI) which result in remarkable differences in the plane-of-array irradiance (POAI) that signifies the maximum available solar photovoltaic potential by combining the latest satellite retrieval results and modeling tools. By separating the impacts of cloud and aerosol on the POAI, it is found that clouds are responsible for the most reduction of POAI in the SC, while aerosols and clouds are equally important for the NI region. The frequent occurrences of low and middle level clouds with high optical depth in the SC, as compared with the much lower occurrences of all levels of clouds with lower optical depth in the NI, is regarded as the major reason for the differences in the POAI. The differences in the main compositions of aerosols in the SC (sulfate) and the NI (dust) could be essential to answer the question of why higher aerosol optical depth in the SC whereas leads to weaker reduction in the POAI than that in the NI. The mitigation measures targeting on the controls of different types of aerosols should be considered for different regions.
| S-EPMC9669044 | biostudies-literature
Project description:BackgroundFrom 1999 to 2010, annual disbursements of development assistance for health for vaccinations increased from $0.5 billion to $2.0 billion (all financial values USD 2010). In its 2012 Global Vaccine Action Plan (GVAP), the World Health Assembly recommended establishing a comprehensive vaccination resource tracking system to better understand the source and recipients of these funds, and ultimately their impact on outcomes. This systematic review aims to respond to the GVAP recommendation in reviewing and assessing the state of the data and literature on vaccination resource tracking.MethodsWe scrutinized all relevant vaccination resource tracking systems identified in the literature and by practitioners in the field. We examined schemes used elsewhere in the health sector and by other sectors. Informant interviews were also conducted to determine what data exists and how it might be utilized. With this information, we completed a qualitative assessment of existing approaches to vaccination resources tracking.ResultsTracking systems provide information about some vaccine-related activity in the majority of low- and middle-income countries. Data are generally available for the period of 2006-2010. Levels of granularity vary. Interviewees were concerned about the degree of rigor used to validate the data and the lack of verification. Data are often presented in tabular form, which may be unwieldy for non-technical audiences.ConclusionsThe schemes currently in place to track the resources available for vaccinations were fairly advanced relative to other mechanisms in the health sector. Nonetheless, the coverage, validity, and accessibility of vaccination resource tracking data could be ameliorated. Establishing improved feedback loops and verification mechanisms that connect country-level administrators and the international organizations that support reporting efforts would enhance data quality.
| S-EPMC4263052 | biostudies-literature