Photomobile Polymer–Piezoelectric Composite for Enhanced Actuation and Energy Generation
Ontology highlight
ABSTRACT:
SUBMITTER: Sagnelli D
PROVIDER: S-EPMC10616835 | biostudies-literature | 2023 Sep
REPOSITORIES: biostudies-literature
Similar Datasets
Project description:Harvesting mechanical energy from biological systems possesses great potential for in vivo powering implantable electronic devices. In this paper, a development of flexible piezoelectric nanogenerator (NG) is reported based on mesoporous poly(vinylidene fluoride) (PVDF) films. Monolithic mesoporous PVDF is fabricated by a template-free sol-gel-based approach at room temperature. By filling the pores of PVDF network with poly(dimethylsiloxane) (PDMS) elastomer, the composite's modulus is effectively tuned over a wide range down to the same level of biological systems. A close match of the modulus between NG and the surrounding biological component is critical to achieve practical integration. Upon deformation, the composite NG exhibits appreciable piezoelectric output that is comparable to or higher than other PVDF-based NGs. An artificial artery system is fabricated using PDMS with the composite NG integrated inside. Effective energy harvesting from liquid pressure fluctuation (simulating blood pressure fluctuation) is successfully demonstrated. The simple and effective approach for fabricating mesoporous PVDF with tunable mechanical properties provides a promising route toward the development of self-powered implantable devices.
| S-EPMC5462116 | biostudies-literature
Project description:Multilayered, aligned arrays of organic nanowires show unique advantages in their piezoelectric response. Here, the cooperative, electromechanical mechanism at the base of the enhanced response of aligned arrays of piezoelectric nanostructures in mutual contact is unveiled. An enhancement of the piezoelectric voltage by two orders of magnitude compared with individual nanofibers is demonstrated in the arrays.
| S-EPMC4282026 | biostudies-literature
Project description:Lightweight flexible piezoelectric polymers are demanded for various applications. However, the low instinctively piezoelectric coefficient (i.e. d33) and complex poling process greatly resist their applications. Herein, we show that introducing dynamic pressure during fabrication is capable for poling polyvinylidene difluoride/barium titanate (PVDF/BTO) composites with d33 of ~51.20 pC/N at low density of ~0.64 g/cm3. The melt-state dynamic pressure driven energy implantation induces structure evolutions of both PVDF and BTO are demonstrated as reasons for self-poling. Then, the porous material is employed as pressure sensor with a high output of ~20.0 V and sensitivity of ~132.87 mV/kPa. Besides, the energy harvesting experiment suggests power density of ~58.7 mW/m2 can be achieved for 10 N pressure with a long-term durability. In summary, we not only provide a high performance lightweight, flexible piezoelectric polymer composite towards sustainable self-powered sensing and energy harvesting, but also pave an avenue for electrical-free fabrication of piezoelectric polymers.
| S-EPMC10821934 | biostudies-literature
Project description:In this study, we investigated an energy harvesting effect of tensile stress using piezoelectric polymers and flexible electrodes. A chemical-vapor-deposition grown graphene film was transferred onto both sides of the PVDF and P(VDF-TrFE) films simultaneously by means of a conventional wet chemical method. Output voltage induced by sound waves was measured and analyzed when a mechanical tension was applied to the device. Another energy harvester was made with a metallic electrode, where Al and Ag were deposited by using an electron-beam evaporator. When acoustic vibrations (105 dB) were applied to the graphene/PVDF/graphene device, an induced voltage of 7.6 Vpp was measured with a tensile stress of 1.75 MPa, and this was increased up to 9.1 Vpp with a stress of 2.18 MPa for the metal/P(VDF-TrFE)/metal device. The 9 metal/PVDF/metal layers were stacked as an energy harvester, and tension was applied by using springs. Also, we fabricated a full-wave rectifying circuit to store the electrical energy in a 100 μF capacitor, and external vibration generated the electrical charges. As a result, the stored voltage at the capacitor, obtained from the harvester via a bridge diode rectifier, was saturated to ~7.04 V after 180 s charging time.
| S-EPMC5725581 | biostudies-literature
Project description:In this study we fabricated a piezoelectric nanogenerator (PENG) of nanocomposite thin film comprising a conductive nanofiller of reduced graphene oxide (rGO) dispersed in a poly(vinylidene fluoride-co-trifluoroethylene) (P(VDF-TrFE)) matrix that was anticipated to show enhanced energy harvest performance. For the film preparation we employed the Langmuir-Schaefer (LS) technique to provide direct nucleation of the polar β-phase without any traditional polling or annealing process. We prepared five PENGs consisting of the nanocomposite LS films with different rGO contents in the P(VDF-TrFE) matrix and optimized their energy harvest performance. We found that the rGO-0.002 wt% film yielded the highest peak-peak open-circuit voltage (VOC) of 88 V upon bending and releasing at 2.5 Hz frequency, which was more than two times higher than the pristine P(VDF-TrFE) film. This optimized performance was explained by increased β-phase content, crystallinity, and piezoelectric modulus, and improved dielectric properties, based on scanning electron microscopy (SEM), Fourier transform infrared (FT-IR), x-ray diffraction (XRD), piezoelectric modulus, and dielectric property measurement results. This PENG with enhanced energy harvest performance has great potential in practical applications for low energy power supply in microelectronics such as wearable devices.
| S-EPMC10005479 | biostudies-literature
Project description:Radiation pressure and photothermal forces have been previously used to optically actuate micro/nanomechanical structures fabricated from semiconductor piezoelectric materials such as gallium arsenide (GaAs). In these materials, coupling of the photovoltaic and piezoelectric properties has not been fully explored and leads to a new type of optical actuation that we call the photovoltaic-piezoelectric effect (PVPZ). We demonstrate this effect by electrically measuring, via the direct piezoelectric effect, the optically induced strain in a novel torsional resonator. The micron-scale torsional resonator is fabricated from a lattice-matched single-crystal molecular beam epitaxy (MBE)-grown GaAs photodiode heterostructure. We find that the strain depends on the product of the electro-optic responsivity and piezoelectric constant of GaAs. The photovoltaic-piezoelectric effect has important potential applications, such as in the development of configurable optical circuits, which can be used in neuromorphic photonic chips, processing of big data with deep learning and the development of quantum circuits.
| S-EPMC8433330 | biostudies-literature
Project description:The electric power output of a piezoelectric nanogenerator (PENG) depends on the various physical parameters of the constituent materials, including the piezoelectric coefficient, Young's modulus, and dielectric constant. Herein, we report the mechanical and electrical properties of a poly(vinylidene fluoride)⁻BaTiO₃ (PVDF⁻BTO) composite-based PENG. Variation of the BTO nanoparticle (NP) content enabled the systematic tuning of the physical parameters that are related to power generation in the composite. The Young's modulus of the PVDF⁻BTO composite initially increased, and then eventually decreased, with the increasing BTO content, which was probably due to the clustering effect of the high modulus BTO NPs. The dielectric constant of the composite continuously increased as the BaTiO₃ content increased. The piezoelectric outputs were greatly enhanced at 10 wt% of BTO, where the Young's modulus was the highest. These results indicate that the Young's modulus plays an important role in the piezoelectric power generation of the composite-based PENGs.
| S-EPMC6215192 | biostudies-literature
Project description:Triboelectric and piezoelectric energy harvesters can hardly power most microelectronic systems. Rotational electromagnetic harvesters are very promising alternatives, but their performance is highly dependent on the varying mechanical sources. This study presents an innovative approach to significantly increase the performance of rotational harvesters, based on dynamic coil switching strategies for optimization of the coil connection architecture during energy generation. Both analytical and experimental validations of the concept of self-adaptive rotational harvester were carried out. The adaptive harvester was able to provide an average power increase of 63.3% and 79.5% when compared to a non-adaptive 16-coil harvester for harmonic translation and harmonic swaying excitations, respectively, and 83.5% and 87.2% when compared to a non-adaptive 8-coil harvester. The estimated energy conversion efficiency was also enhanced from ~80% to 90%. This study unravels an emerging technological approach to power a wide range of applications that cannot be powered by other vibrationally driven harvesters.
| S-EPMC11291956 | biostudies-literature
Project description:Structures that are capable of changing shape can increase efficiency in many applications, but are often heavy and maintenance intensive. To reduce the mass and mechanical complexity solid-state morphing materials are desirable but are typically nonstructural and problematic to control. Here we present an electrically controlled solid-state morphing composite material that is lightweight and has a stiffness higher than aluminum. It is capable of producing large deformations and holding them with no additional power, albeit at low rates. The material is manufactured from commercial carbon fibers and a structural battery electrolyte, and uses lithium-ion insertion to produce shape changes at low voltages. A proof-of-concept material in a cantilever setup is used to show morphing, and analytical modeling shows good correlation with experimental observations. The concept presented shows considerable promise and paves the way for stiff, solid-state morphing materials.
| S-EPMC7149449 | biostudies-literature
Project description:Conventional composite sol-gel method has been modified to enhance the piezoelectric performance of ceramic thick films. Lead zirconate titanate (PZT) and lead magnesium niobate-lead titanate (PMN-PT) thick films were fabricated using the modified sol-gel method for ultrasonic transducer applications. In this work, piezoresponse force microscopy was employed to evaluate the piezoelectric characteristics of PZT and PMN-PT composite sol-gel thick films. The images of the piezoelectric response and the strain-electric field hysteresis loop behavior were measured. The effective piezoelectric coefficient (d33,eff) of the films was determined from the measured loop data. It was found that the effective local piezoelectric coefficient of both PZT and PMN-PT composite films is comparable to that of their bulk ceramics. The promising results suggest that the modified composite sol-gel method is a promising way to prepare the high-quality, crack-free ceramic thick films.
| S-EPMC3663855 | biostudies-other