Fabrication of 3D-printed molds for polydimethylsiloxane-based microfluidic devices using a liquid crystal display-based vat photopolymerization process: printing quality, drug response and 3D invasion cell culture assays
Ontology highlight
ABSTRACT:
SUBMITTER: Poskus M
PROVIDER: S-EPMC10632127 | biostudies-literature | 2023 Jan
REPOSITORIES: biostudies-literature
Similar Datasets
Project description:Vat photopolymerization typically prints highly crosslinked networks. Printing hydrogels, which are also networks but with a high swelling capacity in water and therefore with low crosslinking density, is a challenge for this technique. However, it may be of interest in medicine and in other areas, since it would allow for the preparation of this type of 3D-shaped material. In this work, an approach for printing hydrogels via vat photopolymerization that uses a mixture of stable and hydrolysable crosslinkers has been evaluated so that an initial highly crosslinked network can be printed, although after hydrolysis it becomes a network with low crosslinking. This approach has been studied with PEO/PEG-related formulations, that is, with a PEG-dimethacrylate as a stable crosslinker, a PEO-related derivative carrying β-aminoesters as a degradable crosslinker, and PEG-methyl ether acrylate and hydroxyethyl acrylate as monofunctional monomers. A wide family of formulations has been studied, maintaining the weight percentage of the crosslinkers at 15%. Resins have been studied in terms of viscosity, and the printing process has been evaluated through the generation of Jacobs working curves. It has been shown that this approach allows for the printing of pieces of different shapes and sizes via vat photopolymerization, and that these pieces can re-ajust their water content in a tailored fashion through treatments in different media (PBS or pH 10 buffer).
| S-EPMC10452991 | biostudies-literature
Project description:Vat photopolymerization (VP) is a rapidly growing category of additive manufacturing. As VP methods mature the expectation is that the quality of printed parts will be highly reproducible. At present, detailed characterization of the light engines used in liquid crystal display (LCD)-based VP systems is lacking and so it is unclear if they are built to sufficiently tight tolerances to meet the current and/or future needs of additive manufacturing. Herein, we map the irradiance, spectral characteristics, and optical divergence of a nominally 405 nm LCD-based VP light engine. We find that there is notable variation in all of these properties as a function of position on the light engine that cause changes in extent of polymerization and surface texture. We further demonstrate through a derived photon absorption figure of merit and through printed test parts that the spatial heterogeneity observed in the light engine is significant enough to affect part fidelity. These findings help to explain several possible causes of variable part quality and also highlight the need for improved optical performance on LCD-based VP printers.
| S-EPMC9890382 | biostudies-literature
Project description:The current printing mechanism of the bottom-up vat photopolymerization 3D printing technique places a high demand on the fluidity of the UV-curable resin. Viscous high-performance acrylate oligomers are compounded with reactive diluents accordingly to prepare 3D printable UV-curable resins (up to 5000 cps of viscosity), yet original mechanical properties of the oligomers are sacrificed. In this work, an elaborated designed linear scan-based vat photopolymerization system is developed, allowing the adoption of printable UV-curable resins with high viscosity (> 600,000 cps). Briefly, this is realized by the employment of four rollers to create an isolated printing area on the resin tank, which enables the simultaneous curing of the resin and the detachment of cured part from the resin tank. To verify the applicability of this strategy, oligomer dominated UV-curable resin with great mechanical properties, but high viscosity is prepared and applied to the developed system. It is inspiring to find that high stress and strain elastomers and toughened materials could be facilely obtained. This developed vat photopolymerization system is expected to unblock the bottleneck of 3D printed material properties, and to build a better platform for researchers to prepare various materials with diversiform properties developed with 3D printing.
| S-EPMC10353997 | biostudies-literature
Project description:Polydimethylsiloxane (PDMS) or silicone elastomers have garnered considerable attention in the field of medical device applications due to their superior thermal stability. However, conventional manufacturing techniques for silicone elastomers suffer from drawbacks such as cost, lengthy production time, and inherent difficulties in fabricating complex structures. To address these limitations, photosensitive polydimethylsiloxane urethane methacrylate (PDMSUMA) oligomers were synthesized, and their curing behaviors were specifically investigated for vat photopolymerization 3D printing applications. The study focused on exploring the impact of weight ratios between poly(ethylene glycol) dimethacrylate (PEGDMA) and 2-hydroxyethyl methacrylate (HEMA) in the PDMSUMA resin formulation. The addition of PEGDMA as a reactive diluent was found to enhance the printability of the PDMSUMA resin and decrease its viscosity. Thermal, mechanical, and shape memory properties of the 3D-printed specimens were examined. Our findings demonstrate the potential of PDMSUMA resins for developing customizable shape memory materials with tailored properties.
| S-EPMC10795029 | biostudies-literature
Project description:Medical 3D printing is a complex, highly interdisciplinary, and revolutionary technology that is positively transforming the care of patients. The technology is being increasingly adopted at the Point of Care (PoC) as a consequence of the strong value offered to medical practitioners. One of the key technologies within the medical 3D printing portfolio enabling this transition is desktop inverted Vat Photopolymerization (VP) owing to its accessibility, high quality, and versatility of materials. Several reports in the peer-reviewed literature have detailed the medical impact of 3D printing technologies as a whole. This review focuses on the multitude of clinical applications of desktop inverted VP 3D printing which have grown substantially in the last decade. The principles, advantages, and challenges of this technology are reviewed from a medical standpoint. This review serves as a primer for the continually growing exciting applications of desktop-inverted VP 3D printing in healthcare.
| S-EPMC10376892 | biostudies-literature
Project description:Ultraviolet (UV) exposure overdose can cause health issues such as skin burns or other skin damage. In this work, a UV and temperature sensor smartwatch is developed, utilizing a multimaterial 3D printing approach via a vat photopolymerization-digital light processing technique. Photochromic (PC) pigments with different UV sensitivities, UVA (315-400 nm) and UVB (315-280 nm), were utilized to cover a wider range of UV exposure and were mixed in transparent resin, whereas the smartwatch was printed with controlled thickness gradients. A multifunctional sensor was next fabricated by adding a thermochromic (TC) material to PC, which is capable of sensing UV and temperature change. Colorimetric measurements assisted by a smartphone-based application provided instantaneous as well as cumulative UV exposure from sunlight. The mechanical properties of the device were also measured to determine its durability. The prototype of the wearable watch was prepared by fixing the 3D-printed dial to a commercially available silicon wristband suitable for all age groups. The 3D-printed watch is water-resistant and easily removable, allowing for its utilization in multiple outdoor activities. Thus, the developed wearable UV sensor alerts the user to the extent of their UV exposure, which can help protect them against overexposure.
| S-EPMC10993352 | biostudies-literature
Project description:As an energy-efficient additive manufacturing process, vat photopolymerization 3D-printing has become a convenient technology to fabricate functional devices with high resolution and freedom in design. However, due to their permanently crosslinked network structure, photopolymers are not easily reprocessed or repaired. To improve the environmental footprint of 3D-printed objects, herein, we combine the dynamic nature of hydroxyl ester links, undergoing a catalyzed transesterification at elevated temperature, with an acrylate monomer derived from renewable resources. As a sustainable building block, we synthesized an acrylated linseed oil and mixed it with selected thiol crosslinkers. By careful selection of the transesterification catalyst, we obtained dynamic thiol-acrylate resins with a high cure rate and decent storage stability, which enabled the digital light processing (DLP) 3D-printing of objects with a structure size of 550 µm. Owing to their dynamic covalent bonds, the thiol-acrylate networks were able to relax 63% of their initial stress within 22 min at 180 °C and showed enhanced toughness after thermal annealing. We exploited the thermo-activated reflow of the dynamic networks to heal and re-shape the 3D-printed objects. The dynamic thiol-acrylate photopolymers also demonstrated promising healing, shape memory, and re-shaping properties, thus offering great potential for various industrial fields such as soft robotics and electronics.
| S-EPMC9784638 | biostudies-literature
Project description:While vat photopolymerization has many advantages over soft lithography in fabricating microfluidic devices, including efficiency and shape complexity, it has difficulty achieving well-controlled micrometer-sized (smaller than 100 μm) channels in the layer building direction. The considerable light penetration depth of transparent resin leads to over-curing that inevitably cures the residual resin inside flow channels, causing clogs. In this paper, a 3D printing process - in-situ transfer vat photopolymerization is reported to solve this critical over-curing issue in fabricating microfluidic devices. We demonstrate microchannels with high Z-resolution (within 10 μm level) and high accuracy (within 2 μm level) using a general method with no requirements on liquid resins such as reduced transparency nor leads to a reduced fabrication speed. Compared with all other vat photopolymerization-based techniques specialized for microfluidic channel fabrication, our universal approach is compatible with commonly used 405 nm light sources and commercial photocurable resins. The process has been verified by multifunctional devices, including 3D serpentine microfluidic channels, microfluidic valves, and particle sorting devices. This work solves a critical barrier in 3D printing microfluidic channels using the high-speed vat photopolymerization process and broadens the material options. It also significantly advances vat photopolymerization's use in applications requiring small gaps with high accuracy in the Z-direction.
| S-EPMC8854570 | biostudies-literature
Project description:3D printing is gaining traction in research and development as a way to quickly, cheaply, and easily manufacture polydimethylsiloxane (PDMS) molds. The most commonly used method is resin printing, which is relatively expensive and requires specialized printers. This study shows that polylactic acid (PLA) filament printing is a cheaper, more readily available alternative to resin printing, that does not inhibit the curing of PDMS. As a proof of concept, a PLA mold for PDMS-based wells was designed, and 3D printed. We introduce an effective method to smooth the printed PLA mold, based on chloroform vapor treatment. After this chemical post-processing step, the smoothened mold was used to cast a ring of PDMS prepolymer. The PDMS ring was attached to a glass coverslip after oxygen plasma treatment. The PDMS-glass well showed no leakage and was well suited to its intended use. When used for cell culturing, monocyte-derived dendritic cells (moDCs) showed no morphological anomalies, as tested by confocal microscopy, nor did they show an increase in cytokines, as tested using ELISA. This underlines the versatility and strength of PLA filament printing and exemplifies how it can be valuable to a researcher's toolset.
| S-EPMC10059908 | biostudies-literature
Project description:Conventional manufacturing techniques to fabricate microfluidic chips, such as soft lithography and hot embossing process, have limitations that include difficulty in preparing multiple-layered structures, cost- and labor-consuming fabrication process, and low productivity. Digital light processing (DLP) technology has recently emerged as a cost-efficient microfabrication approach for the 3D printing of microfluidic chips; however, the fabrication resolution for microchannels is still limited to sub-100 microns at best. Here, we developed an innovative DLP printing strategy for high resolution and scalable microchannel fabrication by dosing- and zoning-controlled vat photopolymerization (DZC-VPP). Specifically, we proposed a modified mathematical model to precisely predict the accumulated UV irradiance for resin photopolymerization, thereby providing guidance for the fabrication of microchannels with enhanced resolution. By fine-tuning the printing parameters, including optical irradiance, exposure time, projection region, and step distance, we can precisely tailor the penetration irradiance stemming from the photopolymerization of the neighboring resin layers, thereby preventing channel blockage due to UV overexposure or compromised bonding stability owing to insufficient resin curing. Remarkably, this strategy can allow the preparation of microchannels with cross-sectional dimensions of 20 μm × 20 μm using a commercial printer with a pixel size of 10 μm × 10 μm; this is significantly higher resolution than previous reports. In addition, this method can enable the scalable and biocompatible fabrication of microfluidic drop-maker units that can be used for cell encapsulation. In general, the current DZC-VPP method can enable major advances in precise and scalable microchannel fabrication and represents a significant step forward for widespread applications of microfluidics-based techniques in biomedical fields.
| S-EPMC10427687 | biostudies-literature