Carbon/ZrO2 aerogel composite microtube superfoam† † Electronic supplementary information (ESI) available. See DOI: https://doi.org/10.1039/d4ra00109e
Ontology highlight
ABSTRACT:
SUBMITTER: Han D
PROVIDER: S-EPMC10906140 | biostudies-literature | 2024 Mar
REPOSITORIES: biostudies-literature
Similar Datasets
Project description:Carbon composite is one of the most competitive electrode materials for supercapacitor, and improving its energy density remains a significant challenge. The copper oxide/carbon composites with high specific surface area were prepared from the cellulose aerogel loaded with copper salts. The copper oxide/carbon composite electrode material, deriving from copper sulfate, reached a specific capacitance of 1001 F g-1 at 2 A g-1, with an energy density of 139.0 W h kg-1. After 500 cycles, the capacitance retention rate is 98.06%. An asymmetric supercapacitor was assembled using this material as positive electrode material, activated carbon as negative electrode material, and 3.0 M KOH as electrolyte. It exhibited good reversible capacity and low voltage drop loss within a voltage window of 0-1.2 V, and its specific capacitance and energy density achieved 125 F g-1 and 6.3 W h kg-1 at a current density of 0.1 A g-1, respectively.
| S-EPMC11873543 | biostudies-literature
Project description:Resorcinol-formaldehyde/titanium dioxide composite (RF/TiO2) gel was prepared simultaneously by acid catalysis and then dried to aerogel with supercritical fluid CO2. The carbon/titanium dioxide aerogel was obtained by carbonization and then converted to nanoporous titanium carbide/carbon composite aerogel via 800 °C magnesiothermic catalysis. Meanwhile, the evolution of the samples in different stages was characterized by X-ray diffraction (XRD), an energy-dispersive X-ray (EDX) spectrometer, a scanning electron microscope (SEM), a transmission electron microscope (TEM) and specific surface area analysis (BET). The results showed that the final product was nanoporous TiC/C composite aerogel with a low apparent density of 339.5 mg/cm3 and a high specific surface area of 459.5 m2/g. Comparing to C aerogel, it could also be considered as one type of highly potential material with efficient photothermal conversion. The idea of converting oxide-carbon composite into titanium carbide via the confining template and low-temperature magnesiothermic catalysis may provide new sight to the synthesis of novel nanoscale carbide materials.
| S-EPMC7767110 | biostudies-literature
Project description:Novel carbon-Al2O3 and carbon-ZrO2 composite-supported Co catalysts were prepared using the sol-gel method with polyethylene glycol (PEG) as a carbon source, and the effects of the addition of CeO2 to catalysts on the steam reforming of ethanol were investigated. The reactions were carried out in a fixed bed reactor with H2O/EtOH = 12 (mol/mol) and a temperature range of 300 °C to 600 °C. The catalyst characterization was performed by XRD, nitrogen adsorption and desorption isotherms, TG-DTA, XRF and TEM. Although the carbon-Al2O3 composite-supported Co catalysts exhibited a higher conversion of ethanol than the carbon-ZrO2 composite-supported Co catalysts, the effect of the addition of CeO2 was hardly observed for catalysts with Al2O3. In contrast to the case of catalysts with Al2O3, the effect of the addition of CeO2 to catalysts with ZrO2 on the conversion and the hydrogen yield was observed, and the hydrogen yield at 600 °C exceeded that of catalysts with Al2O3. 16Co42C31.5Ce10.5Zr exhibited the highest hydrogen yield of 89% at 600 °C. Fine Co metal species were observed for the used ZrO2-based catalysts, while Co3O4 peaks were observed for the used Al2O3-based catalysts. The development of the carbon nanotube-like structure with a diameter of 50 nm was observed with particles having diameters of 30 nm to 50 nm, suggesting that the carbon deposition might occur so as not to deactivate the catalyst.
| S-EPMC8695227 | biostudies-literature
Project description:Solar desalination of seawater is an effective approach to address the scarcity of freshwater resources. For solar steam generation, it is critical to design biodegradable, sustainable, low-cost, and high-evaporation-rate technology. This study aims to develop a novel solar desalination technology by designing and fabricating a nanocomposite material with excellent light absorption and thermal conversion properties. We designed a double-layer aerogel structure, which uses naturally abundant carboxymethyl cellulose (CMC) as the basic skeleton to achieve sustainability and biodegradability, and uses carbon nanotubes as the photothermal material for efficient light absorption to prepare a ferric tannate/carbon nanotube/carboxymethyl cellulose composite aerogel (FT-CNT-CMC aerogel). Experimental results demonstrate that the FT-CNT-CMC aerogel exhibits a high light absorption rate of 96-98% within the spectral range of 250-2400 nm, showcasing remarkable photothermal conversion performance. Under a sun intensity of 1 kW·m-2, the FT-CNT-CMC aerogel achieves a significant evaporation rate of 1.942 kg·m-2·h-1 at room temperature. Moreover, the excellent performance of the FT-CNT-CMC aerogel is validated in practical seawater desalination and organic dye wastewater purification. The FT-CNT-CMC aerogel exhibits a retention rate exceeding 99% for Na+, Mg2+, K+, and Ca2+ ions in simulated seawater, while no characteristic absorption peaks are observed in methylene blue and rhodamine B dye solutions after purification. These findings highlight the promising potential of the FT-CNT-CMC aerogel in the field of novel solar desalination, providing a viable solution to obtain freshwater.
| S-EPMC10488654 | biostudies-literature
Project description:Carbon deposition following thermal methane decomposition under dry and steam reforming conditions has been studied on yttria-stabilized zirconia (YSZ), Y2O3, and ZrO2 by a range of different chemical, structural, and spectroscopic characterization techniques, including aberration-corrected electron microscopy, Raman spectroscopy, electric impedance spectroscopy, and volumetric adsorption techniques. Concordantly, all experimental techniques reveal the formation of a conducting layer of disordered nanocrystalline graphite covering the individual grains of the respective pure oxides after treatment in dry methane at temperatures T ≥ 1000 K. In addition, treatment under moist methane conditions causes additional formation of carbon-nanotube-like architectures by partial detachment of the graphite layers. All experiments show that during carbon growth, no substantial reduction of any of the oxides takes place. Our results, therefore, indicate that these pure oxides can act as efficient nonmetallic substrates for methane-induced growth of different carbon species with potentially important implications regarding their use in solid oxide fuel cells. Moreover, by comparing the three oxides, we could elucidate differences in the methane reactivities of the respective SOFC-relevant purely oxidic surfaces under typical SOFC operation conditions without the presence of metallic constituents.
| S-EPMC3935620 | biostudies-literature
Project description:Heavy metal wastewater is a direct threat to the ecological environment and human health because it is highly toxic at low concentrations. Therefore, it is very important to explore and develop efficient wastewater treatment agents. MnFe2O4-loaded bamboo pulp carbon-based aerogel (MCA) is prepared by directional freeze-drying and carbonization. SEM, TEM, XPS, XRD, BET and FTIR are used to evaluate the physical and chemical properties of MCA. Meanwhile, the adsorption performances of MCA on Pb2+, Cu2+ and Cd2+ are also studied by adsorption kinetics, isothermal curves and thermodynamics. The results show that the adsorption process involves chemical adsorption and physical adsorption, and the adsorption process is a spontaneous endothermic process. The maximum adsorption capacities of MCA for Pb2+, Cu2+ and Cd2+ obtained in the adsorption isotherm experiments were 74.38, 84.21 and 73.63 mg g-1, respectively, showing excellent adsorption performance for Pb2+, Cu2+ and Cd2+. Therefore, the MCA has potential application for wastewater purification of heavy metals containing Pb2+, Cu2+ and Cd2+, meanwhile, this study provides some guidance for the design and application of microspheres for the separation and removal of Pb2+, Cu2+ and Cd2+.
| S-EPMC11659952 | biostudies-literature
Project description:Flexible microwave absorbers with Joule heating performance are urgently desired to meet the demands of extreme service environments. Herein, a type of flexible composite film is constructed by homogeneously dispersing a hierarchical Ni-carbon microtube (Ni/CMT) into a processable polytetrafluoroethylene (PTFE) matrix. The Ni/CMT are interconnected into a 3D conductive network, in which the huge interior cavity of the carbon microtube (CMT) improves impedance matching and provides additional hyper channels for electromagnetic (EM) waves dissipation, and the hierarchical magnetic Ni nanoparticles enhance the synergistic interactions between confined heterogeneous interfaces. Such an ingenious structure endows the composites with excellent electrothermal performance and improves their serviceability for application under extreme environments. Moreover, under a low fill loading of 3 wt.%, the Ni/CMT/PTFE (NCP) can achieve excellent low-frequency microwave absorption (MA) property with a minimum reflection loss of -59.12 dB at 5.92 GHz, which covers almost the entire C-band. Relying on their brilliant MA property, an EM sensor is designed and achieved by the resonance coupling of the patterned NCP. This work opens up a new way for the design of next-generation microwave absorbers that meet the requirements of EM packaging, proofing water and removing ice, fire safety, and health monitoring.
| S-EPMC10625052 | biostudies-literature
Project description:Biomass-derived materials have recently received considerable attention as lightweight, low-cost, and green microwave absorbers. On the other hand, sulfide nanostructures due to their narrow band gaps have demonstrated significant microwave characteristics. In this research, carbon microtubes were fabricated using a biowaste and then functionalized by a novel complementary solvothermal and sonochemistry method. The functionalized carbon microtubes (FCMT) were ornamented by CuCo2S4 nanoparticles as a novel spinel sulfide microwave absorber. The prepared structures illustrated narrow energy band gap and deposition of the sulfide structures augmented the polarizability, desirable for dielectric loss and microwave attenuation. Eventually, the architected structures were blended by polyacrylonitrile (PAN) to estimate their microwave absorbing and antibacterial characteristics. The antibacterial properties against Gram-negative Escherichia coli (E. coli) and Gram-positive Staphylococcus aureus (S. aureus) were scrupulously assessed. Noteworthy, the maximum reflection loss (RL) of the CuCo2S4/PAN with a thickness of 1.75 mm was 61.88 dB at 11.60 GHz, while the architected FCMT/PAN composite gained a broadband efficient bandwidth as wide as 7.91 GHz (RL > 10 dB) and 3.25 GHz (RL > 20 dB) with a thickness of 2.00 mm. More significantly, FCMT/CuCo2S4/PAN demonstrated an efficient bandwidth of 2.04 GHz (RL > 20 dB) with only 1.75 mm in thickness. Interestingly, FCMT/CuCo2S4/PAN and CuCo2S4/PAN composites demonstrated an electromagnetic interference shielding efficiency of more than 90 and 97% at the entire x and ku-band frequencies, respectively.
| S-EPMC8184785 | biostudies-literature
Project description:The rapid development of communication technology and high-frequency electronic devices has created a need for more advanced electromagnetic interference (EMI) shielding materials. In response to this demand, a study has been conducted to develop multifunctional carbon nanofibers (CNFs)/polyaniline (PANI) aerogels with excellent electromagnetic interference shielding, flame retardancy, and thermal insulation performance. The process involved freeze-drying of electrospun CNFs and PANI nanoparticles followed by in situ growth PANI to coat the CNFs, creating the core-shell structured CNFs/PANI composite fiber and its hybrid aerogels (CP-3@PANI). The interaction between PANI and aniline (ANI) provides attachment sites, allowing additional ANI adsorption into the aerogel for in situ polymerization. This results in PANI uniformly covering the surface of the CNFs, creating a core-shell composite fiber with a flexible CNF core and PANI shell. This process enhances the utilization rate of the ANI monomer and increases the PANI content loaded onto the aerogel. Additionally, effective connections are established between the CNFs, forming a stable, conductive three-dimensional network structure. The prepared CP-3@PANI aerogels exhibit excellent EMI shielding efficiency (SE) of 85.4 dB and specific EMI SE (SE d-1) of 791.2 dB cm3 g⁻1 in the X-band. Due to the synergistic flame-retardant effect of CNFs, PANI, and the dopant (phytic acid), the CP-3@PANI aerogels demonstrate outstanding flame-retardant and thermal insulation properties, with a peak heat release rate (PHRR) as low as 7.8 W g⁻1 and a total heat release of only 0.58 kJ g⁻1. This study provides an effective strategy for preparing multifunctional integrated EMI shielding materials.
| S-EPMC11609142 | biostudies-literature
Project description:In this study, we conducted research on the preparation of aerogels using cellulose and starch as the primary materials, with the addition of N,N'-methylenebisacrylamide (MBA) as a cross-linking agent. The chemical, morphological and textural characteristics of the aerogels were found to be influenced by the proportions of cellulose, starch, and cross-linking agent that were utilized. An increase in the proportion of cellulose led to stronger adsorption forces within the aerogel structure. The aerogel showed a fine mesh internal structure, but the pores gradually increased with the further increase in cellulose. Notably, when the mass fractions of starch and cellulose were 5 wt% and 1 wt% respectively, the aerogels exhibited the smallest pore size and largest porosity. With an increase in the crosslinking agent, the internal structure of the aerogel first became dense and then loose, and the best internal structure was displayed at the addition of 3 wt%. Through texture analysis and the swelling test, the impact of the proportion of cellulose and MBA on the aerogel structure was significant. Dye adsorption experiments indicated that MBA affected the water absorption and expansion characteristics of the aerogel by improving the pore structure. Lastly, in tests involving the loading of vitamin E, the aerogels exhibited a higher capacity for incorporating vitamin E compared to native starch.
| S-EPMC10648849 | biostudies-literature