Dataset Information

Estimating mass properties of dinosaurs using laser imaging and 3D computer modelling.

ABSTRACT: Body mass reconstructions of extinct vertebrates are most robust when complete to near-complete skeletons allow the reconstruction of either physical or digital models. Digital models are most efficient in terms of time and cost, and provide the facility to infinitely modify model properties non-destructively, such that sensitivity analyses can be conducted to quantify the effect of the many unknown parameters involved in reconstructions of extinct animals. In this study we use laser scanning (LiDAR) and computer modelling methods to create a range of 3D mass models of five specimens of non-avian dinosaur; two near-complete specimens of Tyrannosaurus rex, the most complete specimens of Acrocanthosaurus atokensis and Strutiomimum sedens, and a near-complete skeleton of a sub-adult Edmontosaurus annectens. LiDAR scanning allows a full mounted skeleton to be imaged resulting in a detailed 3D model in which each bone retains its spatial position and articulation. This provides a high resolution skeletal framework around which the body cavity and internal organs such as lungs and air sacs can be reconstructed. This has allowed calculation of body segment masses, centres of mass and moments or inertia for each animal. However, any soft tissue reconstruction of an extinct taxon inevitably represents a best estimate model with an unknown level of accuracy. We have therefore conducted an extensive sensitivity analysis in which the volumes of body segments and respiratory organs were varied in an attempt to constrain the likely maximum plausible range of mass parameters for each animal. Our results provide wide ranges in actual mass and inertial values, emphasizing the high level of uncertainty inevitable in such reconstructions. However, our sensitivity analysis consistently places the centre of mass well below and in front of hip joint in each animal, regardless of the chosen combination of body and respiratory structure volumes. These results emphasize that future biomechanical assessments of extinct taxa should be preceded by a detailed investigation of the plausible range of mass properties, in which sensitivity analyses are used to identify a suite of possible values to be tested as inputs in analytical models.

SUBMITTER: Bates KT

PROVIDER: S-EPMC2639725 | biostudies-literature | 2009

REPOSITORIES: biostudies-literature

ACCESS DATA

Publications

Estimating mass properties of dinosaurs using laser imaging and 3D computer modelling.

Bates Karl T KT Manning Phillip L PL Hodgetts David D Sellers William I WI

PloS one 20090219 2

Body mass reconstructions of extinct vertebrates are most robust when complete to near-complete skeletons allow the reconstruction of either physical or digital models. Digital models are most efficient in terms of time and cost, and provide the facility to infinitely modify model properties non-destructively, such that sensitivity analyses can be conducted to quantify the effect of the many unknown parameters involved in reconstructions of extinct animals. In this study we use laser scanning (L ...[more]

PMID: 19225569

Similar Datasets

Project description:In vivo and ex vivo sensors have the potential to aid tracking and anti-poaching endeavours and provide new insights into rhinoceros physiology and environment. However, the propagation of electromagnetic signals in rhinoceros tissue is currently not known. We present simulation and agar models of the rhinoceros that allow the investigation of electromagnetic propagation by in vivo and ex vivo devices without the need for surgery. Since the dielectric properties of rhinoceros tissue have not been documented, the conductivity and permittivity of the skin, fat, muscle, blood and other organs are first approximated by means of a meta-analysis that includes animals with similar physical properties. Subsequently, we develop anatomical models that include dermal layers, internal organs and a skeleton. We also develop a flank model that serves as an approximation of the anatomical model in certain situations. These models are used to determine the viability of communication between an in vivo device and an ex vivo device attached to the hind leg of the animal. Two types of antenna (microstrip-fed planar elliptical monopole antenna and printed inverted-F antenna) and three feasible implant locations (back, neck and chest) are considered. In addition to the computer models, phantom recipes using salt, sugar and agar are developed to match the dielectric properties of each tissue type at the industrial, scientific and medical (ISM) frequencies of 403MHz, 910MHz and 2.4GHz. The average error between the measured and theoretically predicted dielectric values was 6.22% over all recipes and 4.49% for the 2.4 GHz recipe specifically. When considering the predicted efficiency of the transmitting and receiving antennas, an agreement of 67.38% was demonstrated between the computer simulations and laboratory measurements using the agar rhinoceros flank models. Computer simulations using the anatomical model of the rhinoceros indicate that the chest is the optimal implant location and that best signal propagation is achieved using the planar inverted-F antenna (PIFA). Using this configuration, the simulations indicate that communication between the implant and an ex vivo device attached to the hind leg is challenging but possible. Furthermore, we find that the inclusion of factors such as the density and temperature of the phantom materials were found to be critical to the achievement of good agreement between practice and simulation.

Project description:Mass spectrometry imaging (MSI) is becoming an increasingly popular analytical technique to investigate microbial systems. However, differences in the ionization efficiencies of distinct MSI methods lead to biases in terms of what types and classes of molecules can be detected. Here, we sought to increase the molecular coverage of microbial colonies by employing metal-assisted laser desorption/ionization (MetA-LDI) MSI, and we compared our results to more commonly utilized matrix-assisted laser desorption/ionization MALDI MSI. We found substantial (∼67%) overlap in the molecules detected in our analysis of Bacillus subtilis colony biofilms using both methods, but each ionization technique did lead to the identification of a unique subset of molecular species. MetA-LDI MSI tended to identify more small molecules and neutral lipids, whereas MALDI MSI more readily detected other lipids and surfactin species. Putative annotations were made using METASPACE, Metlin, and the BsubCyc database. These annotations were then confirmed from analyses of replicate bacterial colonies using liquid extraction surface analysis tandem mass spectrometry. Additionally, we analyzed B. subtilis biofilms in a polymer-based emulated soil micromodel using MetA-LDI MSI to better understand bacterial processes and metabolism in a native, soil-like environment. We were able to detect different molecular signatures within the micropore regions of the micromodel. We also show that MetA-LDI MSI can be used to analyze microbial biofilms from electrically insulating material. Overall, this study expands the molecular universe of microbial metabolism that can be visualized by MSI. IMPORTANCE Matrix-assisted laser desorption/ionization mass spectrometry imaging is becoming an important technique to investigate molecular processes within microbial colonies and microbiomes under different environmental conditions. However, this method is limited in terms of the types and classes of molecules that can be detected. In this study, we utilized metal-assisted laser desorption/ionization mass spectrometry imaging, which expanded the range of molecules that could be imaged from microbial samples. One advantage of this technique is that the addition of a metal helps facilitate ionization from electrically nonconductive substrates, which allows for the investigation of biofilms grown in polymer-based devices, like soil-emulating micromodels.

Dataset Information

Estimating mass properties of dinosaurs using laser imaging and 3D computer modelling.

Publications

Estimating mass properties of dinosaurs using laser imaging and 3D computer modelling.

Similar Datasets

OmicsDI is part of the ELIXIR infrastructure

Tweets