Dataset Information

Comparison of dust released from sanding conventional and nanoparticle-doped wall and wood coatings.

ABSTRACT: Introduction of engineered nanoparticles (ENPs) into traditional surface coatings (e.g., paints, lacquers, fillers) may result in new exposures to both workers and consumers and possibly also a new risk to their health. During finishing and renovation, such products may also be a substantial source of exposure to ENPs or aggregates thereof. This study investigates the particle size distributions (5.6?nm-19.8??m) and the total number of dust particles generated during sanding of ENP-doped paints, lacquers, and fillers as compared to their conventional counterparts. In all products, the dust emissions from sanding were found to consist of five size modes: three modes under 1??m and two modes around 1 and 2??m. Corrected for the emission from the sanding machine, the sanding dust, was dominated by 100-300?nm size particles, whereas the mass and surface area spectra were dominated by the micrometer modes. Adding ENPs to the studied products only vaguely affected the geometric mean diameters of the particle modes in the sanding dust when compared to their reference products. However, we observed considerable differences in the number concentrations in the different size modes, but still without revealing a clear effect of ENPs on dust emissions from sanding.

SUBMITTER: Koponen IK

PROVIDER: S-EPMC3119175 | biostudies-literature | 2011 Jul-Aug

REPOSITORIES: biostudies-literature

ACCESS DATA

Publications

Comparison of dust released from sanding conventional and nanoparticle-doped wall and wood coatings.

Koponen Ismo Kalevi IK Jensen Keld Alstrup KA Schneider Thomas T

Journal of exposure science & environmental epidemiology 20100519 4

Introduction of engineered nanoparticles (ENPs) into traditional surface coatings (e.g., paints, lacquers, fillers) may result in new exposures to both workers and consumers and possibly also a new risk to their health. During finishing and renovation, such products may also be a substantial source of exposure to ENPs or aggregates thereof. This study investigates the particle size distributions (5.6 nm-19.8 μm) and the total number of dust particles generated during sanding of ENP-doped paints, ...[more]

PMID: 20485339

Similar Datasets

Project description:During production, thermally modified wood is processed using the same machining operations as unmodified wood. Machining wood is always accompanied with the creation of dust particles. The smaller they become, the more hazardous they are. Employees are exposed to a greater health hazard when machining thermally modified wood because a considerable amount of fine dust is produced under the same processing conditions than in the case of unmodified wood. The International Agency for Research on Cancer (IARC) states that wood dust causes cancer of the nasal cavity and paranasal sinuses and of the nasopharynx. Wood dust is also associated with toxic effects, irritation of the eyes, nose and throat, dermatitis, and respiratory system effects which include decreased lung capacity, chronic obstructive pulmonary disease, asthma and allergic reactions. In our research, granular composition of particles resulting from the process of longitudinal milling of heat-treated oak and spruce wood under variable conditions (i.e., the temperature of modification of 160, 180, 200 and 220 °C and feed rate of 6, 10 and 15 m.min-1) are presented in the paper. Sieve analysis was used to determine the granular composition of particles. An increase in fine particle fraction when the temperature of modification rises was confirmed by the research. This can be due to the lower strength of thermally modified wood. Moreover, a different effect of the temperature modification on granularity due to the tree species was observed. In the case of oak wood, changes occurred at a temperature of 160 °C and in the case of spruce wood, changes occurred at the temperatures of 200 and 220 °C. At the temperatures of modification of 200 and 220 °C, the dust fraction (i.e., that occurred in the mesh sieves, particles with the size ? 0.08 mm) ranged from 2.99% (oak wood, feed rate of 10 m.min-1) to 8.07% (spruce wood, feed rate of 6 m.min-1). Such particles might have a harmful effect on employee health in wood-processing facilities.

Dataset Information

Comparison of dust released from sanding conventional and nanoparticle-doped wall and wood coatings.

Publications

Comparison of dust released from sanding conventional and nanoparticle-doped wall and wood coatings.

Similar Datasets

OmicsDI is part of the ELIXIR infrastructure

Tweets