Dataset Information

Osteoconductive protamine-based polyelectrolyte multilayer functionalized surfaces.

ABSTRACT: The integration of orthopedic implants with host bone presents a major challenge in joint arthroplasty, spinal fusion and tumor reconstruction. The cellular microenvironment can be programmed via implant surface functionalization allowing direct modulation of osteoblast adhesion, proliferation, and differentiation at the implant--bone interface. The development of layer-by-layer assembled polyelectrolyte multilayer (PEM) architectures has greatly expanded our ability to fabricate intricate nanometer to micron scale thin film coatings that conform to complex implant geometries. The in vivo therapeutic efficacy of thin PEM implant coatings for numerous biomedical applications has previously been reported. We have fabricated protamine-based PEM thin films that support the long-term proliferation and differentiation of pre-osteoblast cells on non-cross-linked film-coated surfaces. These hydrophilic PEM functionalized surfaces with nanometer-scale roughness facilitated increased deposition of calcified matrix by osteoblasts in vitro, and thus offer the potential to enhance implant integration with host bone. The coatings can make an immediate impact in the osteogenic culture of stem cells and assessment of the osteogenic potential of new therapeutic factors.

SUBMITTER: Samuel RE

PROVIDER: S-EPMC3218099 | biostudies-literature | 2011 Oct

REPOSITORIES: biostudies-literature

ACCESS DATA

Publications

Osteoconductive protamine-based polyelectrolyte multilayer functionalized surfaces.

Samuel Raymond E RE Shukla Anita A Paik Daniel H DH Wang Mary X MX Fang Jean C JC Schmidt Daniel J DJ Hammond Paula T PT

Biomaterials 20110718 30

The integration of orthopedic implants with host bone presents a major challenge in joint arthroplasty, spinal fusion and tumor reconstruction. The cellular microenvironment can be programmed via implant surface functionalization allowing direct modulation of osteoblast adhesion, proliferation, and differentiation at the implant--bone interface. The development of layer-by-layer assembled polyelectrolyte multilayer (PEM) architectures has greatly expanded our ability to fabricate intricate nanom ...[more]

PMID: 21764442

Similar Datasets

Project description:The field of membranes saw huge developments in the last decades with the introduction of both polyelectrolyte multilayer (PEM)-based membranes and biomimetic membranes. In this work, we combine these two promising systems and demonstrate that proteopolymersomes (PP+) with the incorporated aquaporin protein can be distributed in a controlled fashion using PEMs, even on the inner surface of a hollow fiber membrane. In this way, various proteopolymersome multilayers (PPMs) are fabricated using PP+ as the positively charged species in combination with the polyanions poly(styrene 4-sulfonate) (PSS) and poly(acrylic acid) (PAA). It is shown by reflectometry through alternately adsorbing the polyanions and PP+ that, for both PAA and PSS, a good layer growth is possible. However, when the multilayers are imaged by SEM, the PAA-based PPMs show dewetting, whereas vesicular structures can only be clearly observed in and on the PSS-based PPMs. In addition, membrane permeability decreases upon coating the PPMs to 2.6 L?m-2?h-1?bar-1 for PAA/PP+ and 7.7 L?m-2?h-1?bar-1 for PSS/PP+. Salt retentions show that PAA/PP+ layers are defective (salt retentions <10% and high molecular weight cut-off (MWCO)), in line with the observed dewetting behavior, while PPMs based on PSS show 80% MgSO4 retention in combination with a low MWCO. The PSS/PP+ membranes show a Donnan-exclusion behavior with moderate MgCl2 retention (50%-55%) and high Na2SO4 retention (85%-90%) indicating a high amount of negative charge present within the PPMs. The corresponding PEMs, on the other hand, are predominately positively charged with MgCl2 retention of 97%-98% and Na2SO4 retention of 57%-80%. This means that the charge inside the multilayer and, thus, its separation behavior can be changed when PP+ is used instead of a polycation. When comparing the PPM membranes to the literature, similar performances are observed with other biomimetic membranes that are not based on interfacial polymerization, but these are the only ones prepared using a desired hollow fiber geometry. Combining PEMs and biomimetic approaches can, thus, lead to relevant membranes, especially adding to the versatility of both systems.

Project description:Over the past decade polyelectrolyte multilayer (PEM)-based membranes have gained a lot of interest in the field of nanofiltration (NF) as an alternative to conventional polyamide-based thin film composite membranes. With great variety in fabrication conditions, these membranes can achieve superior properties such as high chemical resistance and excellent filtration performance. Some of the most common polyelectrolytes used to prepare NF membranes are weak, meaning that their charge density depends on pH within the normal window of operation relevant for potential applications (pH 0-14). This might cause a dependency of membrane properties on the pH of filtered solutions, as indicated by other applications of PEMs. In this work, the susceptibility of membrane structure (swelling and surface charge) and performance (permeability, molecular weight cutoff, and salt retention) toward the pH of the filtration solution was studied for four fundamentally different PEM systems: poly(diallyldimethylammonium chloride) (PDADMAC)/poly(sodium-4-styrenesulfonate) (PSS) (strong/strong), poly(allylamine hydrochloric acid) (PAH)/poly(acrylic acid) (PAA) (weak/weak), and PAH/PSS (weak/strong) and PAH/PSS+PAH/PAA (asymmetric). Slight variations in structure and performance of the PDADMAC/PSS-based membranes were observed. On the contrary, structure and performance of PAH/PAA-based membranes are very susceptible to feed solution pH. A continuous change in charge density with variation in pH significantly affects salt retention. An increased swelling at pH 9 translates to variation in permeability and molecular weight cutoff of the membrane. The susceptibility of PAH/PSS-based membranes to pH is less pronounced compared to the PAH/PAA-based membranes since only one of the polyelectrolytes involved is weak. No structural changes were observed, indicating additional specific interactions between the polyelectrolytes other than electrostatic forces that stabilize film structure. A combination of the PAH/PSS and PAH/PAA system (8 + 2 bilayers) also displays a clear dependency of both membrane structure and performance on solution pH, where PAH/PSS is dominating due to a higher bilayer number.

Dataset Information

Osteoconductive protamine-based polyelectrolyte multilayer functionalized surfaces.

Publications

Osteoconductive protamine-based polyelectrolyte multilayer functionalized surfaces.

Similar Datasets

OmicsDI is part of the ELIXIR infrastructure

Tweets