Browse
Submit Data
Databases
API
Help

Dataset Information

11 Views

0 Connections

0 Citations

0 Reanalyses

0 Downloads

Omics score: 0

Preparation of Monolithic Capillary Chromatographic Columns Using Supercritical Fluid as a Porogen Solvent.

ABSTRACT: Monolithic polymeric beds were synthesized in fused silica capillaries using either trimethylolpropane trimethacrylate (TRIM) or a mixture of butyl methacrylate (BMA) with ethylene glycol dimethacrylate (EDMA) as monomers. Carbon dioxide at temperature and pressure conditions above its critical values was used as a porogen solvent. The purpose of using the supercritical carbon dioxide was to have the possibility of changing the solvation power (and thus the porosity of the resulting monolith) of the porogen by pressure and temperature changes instead of changing the porogen composition. The experiments were performed using a special setup consisting of a stainless steel high-pressure reactor to which the fused silica capillary was connected. The synthesized monoliths underwent liquid chromatographic evaluation. The polyTRIM capillary monoliths were characterized by different permeability, which depended on the pressure of the synthesis. BMA/EDMA columns were applied for separation of alkylbenzenes and a model mixture of proteins.

SUBMITTER: Szumski M

PROVIDER: S-EPMC4111859 | biostudies-literature |

REPOSITORIES: biostudies-literature

ACCESS DATA

Json Xml

Similar Datasets

Improvement of the liquid-chromatographic analysis of protein tryptic digests by the use of long-capillary monolithic columns with UV and MS detection.

Project description:Optimisation of peak capacity is an important strategy in gradient liquid chromatography (LC). This can be achieved by using either long columns or columns packed with small particles. Monolithic columns allow the use of long columns at relatively low back-pressure. The gain in peak capacity using long columns was evaluated by the separation of a tryptic bovine serum albumin digest with an LC-UV-mass spectrometry (MS) system and monolithic columns of different length (150 and 750 mm). Peak capacities were determined from UV chromatograms and MS/MS data were used for Mascot database searching. Analyses with a similar gradient slope for the two columns produced ratios of the peak capacities that were close to the expected value of the square root of the column length ratio. Peak capacities of the short column were 12.6 and 25.0 with 3 and 15 min gradients, respectively, and 29.7 and 41.0 for the long column with 15 and 75 min gradients, respectively. Protein identification scores were also higher for the long column, 641 and 750 for the 3- and 15-min gradients with the short column and 1,376 and 993 for the 15- and 75-min gradients with the long column. Thus, the use of long monolithic columns provides improved peptide separation and increased reliability of protein identification.

| S-EPMC1914286 | biostudies-other

Improved Sensitivity of Ultralow Flow LC-MS-Based Proteomic Profiling of Limited Samples Using Monolithic Capillary Columns and FAIMS Technology.

Project description:In this work, we pioneered a combination of ultralow flow (ULF) high-efficiency ultranarrow bore monolithic LC columns coupled to MS via a high-field asymmetric waveform ion mobility spectrometry (FAIMS) interface to evaluate the potential applicability for high sensitivity, robust, and reproducible proteomic profiling of low nanogram-level complex biological samples. As a result, ULF LC-FAIMS-MS brought unprecedented sensitivity levels and high reproducibility in bottom-up proteomic profiling. In addition, FAIMS improved the dynamic range, signal-to-noise ratios, and detection limits in ULF LC-MS-based measurements by significantly reducing chemical noise in comparison to the conventional nanoESI interface used with the same ULF LC-MS setup. Two, three, or four compensation voltages separated by at least 15 V were tested within a single LC-MS run using the FAIMS interface. The optimized ULF LC-ESI-FAIMS-MS/MS conditions resulted in identification of 2,348 ± 42 protein groups, 10,062 ± 285 peptide groups, and 15,734 ± 350 peptide-spectrum matches for 1 ng of a HeLa digest, using a 1 h gradient at the flow rate of 12 nL/min, which represents an increase by 38%, 91%, and 131% in respective identifications, as compared to the control experiment (without FAIMS). To evaluate the practical utility of the ULF LC-ESI-FAIMS-MS platform in proteomic profiling of limited samples, approximately 100, 1,000, and 10,000 U937 myeloid leukemia cells were processed, and a one-tenth of each sample was analyzed. Using the optimized conditions, we were able to reliably identify 251 ± 54, 1,135 ± 80, and 2,234 ± 25 protein groups from injected aliquots corresponding to ?10, 100, and 1,000 processed cells.

| S-EPMC7934643 | biostudies-literature

Surfactant-bound monolithic columns for CEC.

Project description:A novel anionic surfactant bound monolithic stationary phase based on 11-acrylaminoundecanoic acid is designed for CEC. The monolith possessing bonded undecanoyl groups (hydrophobic sites) and carboxyl groups (weak cationic ion-exchange sites) were evaluated as a mixed-mode stationary phase in CEC for the separation of neutral and polar solutes. Using a multivariate D-optimal design the composition of the polymerization mixture was modeled and optimized with five alkylbenzenes and seven alkyl phenyl ketones as test solutes. The D-optimal design indicates a strong dependence of electrochromatographic parameters on the concentration of 11-acrylaminoundecanoic acid monomer and porogen (water) in the polymerization mixture. A difference of 6, 8 and 13% RSD between the predicted and the experimental values in terms of efficiency, resolution and retention time, respectively, indeed confirmed that the proposed approach is practical. The physical (i.e. morphology, porosity and permeability) and chromatographic properties of the monolithic columns were thoroughly investigated. With the optimized monolithic column, high efficiency separation of N-methylcarbamates pesticides and positional isomers was successfully achieved. It appears that this type of mixed-mode monolith (containing both chargeable and hydrophobic sites) may have a great potential as a new generation of CEC stationary phase.

| S-EPMC2856648 | biostudies-literature

Preparation of Chitosan-Based Hemostatic Sponges by Supercritical Fluid Technology.

Project description:Using ammonium bicarbonate (AB) particles as a porogen, chitosan (CS)-based hemostatic porous sponges were prepared in supercritical carbon dioxide due to its low viscosity, small surface tension, and good compatibility with organic solvent. Fourier transform infrared spectroscopy (FTIR) spectra demonstrated that the chemical compositions of CS and poly-(methyl vinyl ether-co-maleic anhydride) (PVM/MA) were not altered during the phase inversion process. The morphology and structure of the sponge after the supercritical fluid (SCF) process were observed by scanning electron microscopy (SEM). The resulting hemostatic sponges showed a relatively high porosity (about 80%) with a controllable pore size ranging from 0.1 to 200 µm. The concentration of PVM/MA had no significant influence on the porosity of the sponges. Comparative experiments on biological assessment and hemostatic effect between the resulting sponges and Avitene® were also carried out. With the incorporation of PVM/MA into the CS-based sponges, the water absorption rate of the sponges increased significantly, and the CS-PVM/MA sponges showed a similar water absorption rate (about 90%) to that of Avitene®. The results of the whole blood clotting experiment and animal experiment also demonstrated that the clotting ability of the CS-PVM/MA sponges was similar to that of Avitene®. All these results elementarily verified that the sponges prepared in this study were suitable for hemostasis and demonstrated the feasibility of using SCF-assisted phase inversion technology to produce hemostatic porous sponges.

| S-EPMC5453353 | biostudies-other

Characterization of triacontyl (C-30) liquid chromatographic columns.

Project description:Differences in the characteristics of seventeen commercial C-30 liquid chromatographic columns were studied for the separation of carotenoid isomers. A mixture consisting of nine xanthophyll and hydrocarbon carotenoids were separated under conditions carefully chosen to reveal changes in selectivity. The influence of the mobile phase composition, column temperature, and mobile phase flow rate were evaluated. Shape selectivity was characterized with Standard Reference Material (SRM) 869b Column Selectivity Test Mixture, for correlation with carotenoid retention behavior. Regular changes were observed across a broad spectrum of shape selectivity characteristics as indicated by SRM 869b. Better separations of carotenoid isomers were achieved with C-30 columns than were possible with C-18 columns, even after optimization of separation conditions.

| S-EPMC7500856 | biostudies-literature

Heterogeneously Catalyzed Continuous-Flow Hydrogenation Using Segmented Flow in Capillary Columns.

Project description: Not available

| S-EPMC3149126 | biostudies-literature

Synthesis and Characterisation of a Monolithic Imprinted Column Using a Methacrylic Acid Monomer with Porogen Propanol for Atenolol Analysis.

Project description:A monolithic imprinted atenolol column was constructed by in situ polymerisation using a methacrylic acid monomer and a 1?:?1 (v/v) porogen of propanol: toluene with two template: monomer: crosslinker combinations, namely, MIP 1 (1?:?4?:?20) and MIP 2 (1?:?5?:?20). Physical characterisation of the monolithic columns consisted of permeability testing, Fourier transform infrared (FTIR) testing, surface area analysis (SAA), and scanning electron microscopy (SEM). The permeability value of four monolithic columns was in the good category: MIP 1 (24.01 mD), NIP 1 (56.43 mD), MIP 2 (23.03 mD), and NIP 2 (14.47 mD). The polymerisation process of these four monolithic imprinted columns was carried out perfectly, as shown by the absence of vinyl groups (1000?cm-1 and 900?cm-1) during FTIR testing. Based on SAA testing, the pores of the four polymers were classified as mesopores. The best monolithic column was MIP 1, as seen from the intercolumn and intracolumn reproducibility values and a % RSD <2.0%. The MIP 1 column was selective towards atenolol, as seen from the selectivity factor, imprinting factor (IF), and resolution (Rs) values. The IF values of MIP 1 were atenolol (204.62), metoprolol (3.36), and propranolol (1.27). The Rs value between atenolol and the analogue compounds was 7.23. The MIP 1 column can be used for the analysis of atenolol in blood serum samples with an average percentage recovery rate of 94.88?±?4.43%.

| S-EPMC7064834 | biostudies-literature

Enrichment of glycoproteins using nanoscale chelating concanavalin A monolithic capillary chromatography.

Project description:Immobilized lectin chromatography can be employed for glycoprotein enrichment, but commonly used columns have limitations of yield and resolution. To improve efficiency and to make the technique applicable to minimal sample material, we have developed a nanoscale chelating Concanavalin A (Con A) monolithic capillary prepared using GMA-EDMA (glycidyl methacrylate-co-ethylene dimethacrylate) as polymeric support. Con A was immobilized on Cu(II)-charged iminodiacetic acid (IDA) regenerable sorbents by forming a IDA:Cu(II):Con A sandwich affinity structure that has high column capacity, as well as stability. When compared with conventional Con A lectin chromatography, the monolithic capillary enabled the better reproducible detection of over double the number of unique N-glycoproteins in human urine samples. Utility for analysis of minimal biological samples was confirmed by the successful elucidation of glycoprotein profiles in mouse urine samples at the microliter scale. The improved efficiency of the nanoscale monolithic capillary will impact the analysis of glycoproteins in complex biological samples, especially where only limited material may be available.

| S-EPMC2759973 | biostudies-literature

Separation of saccharides using fullerene-bonded silica monolithic columns via π interactions in liquid chromatography.

Project description:We report on a potential method to separate sugars by using the specific interaction between fullerenes and saccharides in liquid chromatography (LC). Aromatic rings with high electron density are believed to interact strongly with saccharides due to CH-π and/or OH-π interactions. In this study, the fullerene-bonded columns were used to separate saccharides by LC under aqueous conditions. As a result, 2-aminobenzamide-labeled glucose homopolymer (Glcs) was effectively separated by both C60 and C70 columns in the range of Glc-1 to Glc-20 and high blood glucose level being retained in greater quantity. Furthermore, similar separations were identified by LC-mass spectrometry with non-labeled glucose homopolymers. Theoretical study based on molecular dynamics and DFT calculation demonstrated that a supramolecular complex of saccharide-fullerene was formed through CH-π and/or OH-π interactions, and that the interactions between saccharide and fullerene increase with the increase units of the saccharide. Additionally, the C60 column retained disaccharides containing maltose, trehalose, and sucrose. In this case, it was assumed that the retention rates were determined by the difference of the dipole moment in each saccharide. These results suggest that the dipole-induced dipole interaction was dominant, and that maltose-with the higher dipole moment-was more strongly retained compared to other disaccharides having lower dipole moment.

| S-EPMC7429847 | biostudies-literature

Sequential two-step chromatographic purification of infectious poliovirus using ceramic fluoroapatite and ceramic hydroxyapatite columns.

Project description:Infectious virus purification techniques are important for vaccine development and gene therapy applications. However, the standardized one-step purification technique using ceramic hydroxyapatite (CHAp) has proven unsuitable for poliovirus. Therefore, we designed a sequential two-step chromatographic technique for purification of the infectious Sabin type 2 vaccine strain of poliovirus from the cell culture supernatant. In the first step, we removed protein contaminants from the Sabin type 2 virus fraction by pH gradient elution on a ceramic fluoroapatite column. In the second step, we removed double-stranded DNA derived from host cells by diluting the virus fraction, directly loading it on a CHAp column, and purifying it using a phosphate gradient with 1 M sodium chloride. This process achieved removal rates of more than 99.95% and 99.99% for proteins and double-stranded DNA, respectively, and was highly reproducible and scalable. Furthermore, it is likely that it will be applicable to other virus species.

| S-EPMC6752803 | biostudies-literature

OmicsDI is part of the ELIXIR infrastructure

OmicsDI is an Elixir interoperability service. Learn more ›

Tweets

OmicsDI Databases

PRIDE
PeptideAtlas
MassIVE
JPOST Repository
Physiome Model Repository

EGA
EVA
ENA
LINCS
PAXDB
Cell Collective

MetaboLights
Metabolomics Workbench
MetabolomeExpress
GNPS
BioModels
FAIRDOMHub

ArrayExpress
dbGaP
ExpressionAtlas
GEO
NODE

Information

Databases
Help
API
Contact us
Code on GitHub
Terms of use
Submit Data