Dataset Information

Basic study for ultrasound-based navigation for pedicle screw insertion using transmission and backscattered methods.

ABSTRACT: The purpose of this study was to understand the acoustic properties of human vertebral cancellous bone and to study the feasibility of ultrasound-based navigation for posterior pedicle screw fixation in spinal fusion surgery. Fourteen human vertebral specimens were disarticulated from seven un-embalmed cadavers (four males, three females, 73.14 ± 9.87 years, two specimens from each cadaver). Seven specimens were used to measure the transmission, including tests of attenuation and phase velocity, while the other seven specimens were used for backscattered measurements to inspect the depth of penetration and A-Mode signals. Five pairs of unfocused broadband ultrasonic transducers were used for the detection, with center frequencies of 0.5 MHz, 1 MHz, 1.5 MHz, 2.25 MHz, and 3.5 MHz. As a result, good and stable results were documented. With increased frequency, the attenuation increased (P<0.05), stability of the speed of sound improved (P<0.05), and penetration distance decreased (P>0.05). At about 0.6 cm away from the cortical bone, warning signals were easily observed from the backscattered measurements. In conclusion, the ultrasonic system proved to be an effective, moveable, and real-time imaging navigation system. However, how ultrasonic navigation will benefit pedicle screw insertion in spinal surgery needs to be determined. Therefore, ultrasound-guided pedicle screw implantation is theoretically effective and promising.

SUBMITTER: Chen Z

PROVIDER: S-EPMC4393101 | biostudies-literature | 2015

REPOSITORIES: biostudies-literature

ACCESS DATA

Publications

Basic study for ultrasound-based navigation for pedicle screw insertion using transmission and backscattered methods.

Chen Ziqiang Z Wu Bing B Zhai Xiao X Bai Yushu Y Zhu Xiaodong X Luo Beier B Chen Xiao X Li Chao C Yang Mingyuan M Xu Kailiang K Liu Chengcheng C Wang Chuanfeng C Zhao Yingchuan Y Wei Xianzhao X Chen Kai K Yang Wu W Ta Dean D Li Ming M

PloS one 20150410 4

The purpose of this study was to understand the acoustic properties of human vertebral cancellous bone and to study the feasibility of ultrasound-based navigation for posterior pedicle screw fixation in spinal fusion surgery. Fourteen human vertebral specimens were disarticulated from seven un-embalmed cadavers (four males, three females, 73.14 ± 9.87 years, two specimens from each cadaver). Seven specimens were used to measure the transmission, including tests of attenuation and phase velocity, ...[more]

PMID: 25861053

Similar Datasets

Project description:OBJECTIVE:To design and evaluate the accuracy of a novel navigation template suitable for posterior cervical screw placement surgery by using 3D printing technology to improve the existing guiding template design. METHODS:The researchers (including spine surgeons and technicians) used CT to perform thin-slice scanning on 12 cases of normal upper cervical vertebral specimens and defined the screw channels that were completely located in the pedicle without penetrating the cortex as ideal screw channels, then designed the ideal channel of the upper cervical vertebral (atlantoaxial) pedicle screw by computer software which was regarded as the preset values, and recorded the screw entrance point, transverse angle and sagittal angle of the ideal channel. Then, researchers designed the novel navigation templates for placement pedicle screw according to the ideal screw channel preset values and manufactured them with one for every single vertebra by 3D printer. A senior spine surgeon performed the posterior surgery to implant pedicle screw on the specimens by the novel navigation templates, then performed CT thin-slice scanning on the specimens again after removing the screws, and reconstructed the actual screws channel by computer software, recorded the screw entrance point, transverse angle and sagittal angle of the actual channels which were defined as the actual values and evaluated them according to Kawaguchi's pedicle screw evaluation standard finally. The differences between the preoperative preset values of ideal screw channel and the postoperative actual values of actual screw channel were compared by a nonparametric paired rank test. RESULTS:48 screws were placed on 12 cases of upper cervical vertebral specimens in total. It showed that the grade 0, I, II, III channels in this study were 47, 1, 0, 0, respectively. The grade 0 channels accounted for 97.92% of the total number of channels. There was no significant difference with regard to the screw entrance point, the transverse angle, and the sagittal angle between the preoperative preset values of ideal screw channels and the postoperative actual values of actual screw channels. CONCLUSION:To implant pedicle screw assisted with the novel individually navigation template designed by 3D printed in the posterior cervical surgery can improve accuracy of pedicle screw placement and safety of the surgery.

Project description:PurposePedicle screw fixation in the upper cervical spine is a difficult and high-risk procedure. The screw is difficult to place rapidly and accurately, and can lead to serious injury of spinal cord or vertebral artery. The aim of this study was to design an individualized 3D printing navigation template for pedicle screw fixation in the upper cervical spine.MethodsUsing CT thin slices data, we employed computer software to design the navigation template for pedicle screw fixation in the upper cervical spine (atlas and axis). The upper cervical spine models and navigation templates were produced by 3D printer with equal proportion, two sets for each case. In one set (Test group), pedicle screws fixation were guided by the navigation template; in the second set (Control group), the screws were fixed under fluoroscopy. According to the degree of pedicle cortex perforation and whether the screw needed to be refitted, the fixation effects were divided into 3 types: Type I, screw is fully located within the vertebral pedicle; Type II, degree of pedicle cortex perforation is <1 mm, but with good internal fixation stability and no need to renovate; Type III, degree of pedicle cortex perforation is >1 mm or with the poor internal fixation stability and in need of renovation. Type I and Type II were acceptable placements; Type III placements were unacceptable.ResultsA total of 19 upper cervical spine and 19 navigation templates were printed, and 37 pedicle screws were fixed in each group. Type I screw-placements in the test group totaled 32; Type II totaled 3; and Type III totaled 2; with an acceptable rate of 94.60%. Type I screw placements in the control group totaled 23; Type II totaled 3; and Type III totaled 11, with an acceptable rate of 70.27%. The acceptability rate in test group was higher than the rate in control group. The operation time and fluoroscopic frequency for each screw were decreased, compared with control group.ConclusionThe individualized 3D printing navigation template for pedicle screw fixation is easy and safe, with a high success rate in the upper cervical spine surgery.

Dataset Information

Basic study for ultrasound-based navigation for pedicle screw insertion using transmission and backscattered methods.

Publications

Basic study for ultrasound-based navigation for pedicle screw insertion using transmission and backscattered methods.

Similar Datasets

OmicsDI is part of the ELIXIR infrastructure

Tweets