Browse
Submit Data
Databases
API
Help

Dataset Information

26 Views

0 Connections

0 Citations

0 Reanalyses

0 Downloads

Omics score: 0

A flexible and biocompatible triboelectric nanogenerator with tunable internal resistance for powering wearable devices.

ABSTRACT: Recently, triboelectric energy nanogenerators (TENGs) have been paid the most attention by many researchers to convert mechanical energy into electrical energy. TENGs usually have a simple structure and a high output voltage. However, their high internal resistance results in low output power. In this work, we propose a flexible triboelectric energy nanogenerator with the double-side tribological layers of polydimethlysiloxane (PDMS) and PDMS/multiwall carbon nanotube (MWCNT). MWCNTs with different concentrations have been doped into PDMS to tune the internal resistance of triboelectric nanogenerator and optimize its output power. The dimension of the fabricated prototype is ~3.6 cm(3). Three-axial force sensor is used to monitor the applied vertical forces on the device under vertical contact-separation working mode. The Prototype with 10 wt% MWCNT (Prototype I) produces higher output voltage than one with 2 wt% MWCNT (Prototype II) due to its higher dielectric parameter measured by LRC impedance analyzer. The triboelectric output voltages of Prototype I and Prototype II are 30 V and 25 V under the vertical force of 3.0 N, respectively. Their maximum triboelectric output powers are ~130 μW at 6 MΩ and ~120 μW at 8.6 MΩ under vertical forces, respectively.

SUBMITTER: Zhu Y

PROVIDER: S-EPMC4768091 | biostudies-literature |

REPOSITORIES: biostudies-literature

ACCESS DATA

Json Xml

Similar Datasets

Flexible and Wearable PDMS-Based Triboelectric Nanogenerator for Self-Powered Tactile Sensing.

Project description:Flexible electronics devices with tactile perception can sense the mechanical property data of the environment and the human body, and they present a huge potential in the human health system. In particular, the introduction of ultra-flexible and self-powered characteristics to tactile sensors can effectively reduce the problems caused by rigid batteries. Herein, we report a triboelectric nanogenerator (TENG), mainly consisting of an ultra-flexible polydimethylsiloxane (PDMS) film with micro-pyramid-structure and sputtered aluminum electrodes, which achieves highly conformal contact with skin and the self-powered detection of human body motions. The flexible polyethylene terephthalate (PET) film was selected as spacer layer, which made the sensor work in the contact-separation mode and endowed the perfect coupling of triboelectrification and electrostatic induction. Moreover, the controllable and uniform micro-structure PDMS film was fabricated by using the micro-electro-mechanical system (MEMS) manufacturing process, bringing a good sensitivity and high output performance to the device. The developed TENG can directly convert mechanical energy into electric energy and light up 110 green Light-Emitting Diodes (LEDs). Furthermore, the TENG-based sensor displays good sensitivity (2.54 V/kPa), excellent linearity (R2 = 0.99522) and good stability (over 30,000 cycles). By virtue of the compact size, great electrical properties, and great mechanical properties, the developed sensor can be conformally attached to human skin to monitor joint movements, presenting a promising application in wearable tactile devices. We believe that the ultra-flexible and self-powered tactile TENG-based sensor could have tremendous application in wearable electrons.

| S-EPMC6781082 | biostudies-other

Ultrasound-mediated triboelectric nanogenerator for powering on-demand transient electronics.

Project description:On-demand transient electronics, technologies referring subsequent material disintegration under well-defined triggering events and programmed time lines, offer exceptional clinical experiences in diagnosis, treatment, and rehabilitation. Despite potential benefits, such as the elimination of surgical device removal and reduction of long-term inimical effects, their use is limited by the nontransient conventional power supplies. Here, we report an ultrasound-mediated transient triboelectric nanogenerator (TENG) where ultrasound determines energy generation and degradation period. Our findings on finite element method simulation show that porous structures of the poly(3-hydroxybutyrate-co-3-hydroxyvalerate) play an essential role in the triggering transient process of our device under high-intensity ultrasound. Besides, the addition of polyethylene glycol improves triboelectric output performance; the voltage output increased by 58.5%, from 2.625 to 4.160 V. We successfully demonstrate the tunable transient performances by ex vivo experiment using a porcine tissue. This study provides insight into practical use of implantable TENGs based on ultrasound-triggered transient material design.

| S-EPMC8741185 | biostudies-literature

Highly Flexible Triboelectric Nanogenerator Using Porous Carbon Nanotube Composites.

Project description:The rapid development of portable and wearable electronic devices has led researchers to actively study triboelectric nanogenerators (TENGs) that can provide self-powering capabilities. In this study, we propose a highly flexible and stretchable sponge-type TENG, named flexible conductive sponge triboelectric nanogenerator (FCS-TENG), which consists of a porous structure manufactured by inserting carbon nanotubes (CNTs) into silicon rubber using sugar particles. Nanocomposite fabrication processes, such as template-directed CVD and ice freeze casting methods for fabricating porous structures, are very complex and costly. However, the nanocomposite manufacturing process of flexible conductive sponge triboelectric nanogenerators is simple and inexpensive. In the tribo-negative CNT/silicone rubber nanocomposite, the CNTs act as electrodes, increasing the contact area between the two triboelectric materials, increasing the charge density, and improving charge transfer between the two phases. Measurements of the performance of flexible conductive sponge triboelectric nanogenerators using an oscilloscope and a linear motor, under a driving force of 2-7 N, show that it generates an output voltage of up to 1120 V and a current of 25.6 µA. In addition, by using different weight percentages of carbon nanotubes (CNTs), it is shown that the output power increases with the weight percentage of carbon nanotubes (CNTs). The flexible conductive sponge triboelectric nanogenerator not only exhibits good performance and mechanical robustness but can also be directly used in light-emitting diodes connected in series. Furthermore, its output remains extremely stable even after 1000 bending cycles in an ambient environment. In sum, the results demonstrate that flexible conductive sponge triboelectric nanogenerators can effectively power small electronics and contribute to large-scale energy harvesting.

| S-EPMC10006981 | biostudies-literature

Smart Wearable Sensors Based on Triboelectric Nanogenerator for Personal Healthcare Monitoring.

Project description:Accurate monitoring of motion and sleep states is critical for human health assessment, especially for a healthy life, early diagnosis of diseases, and medical care. In this work, a smart wearable sensor (SWS) based on a dual-channel triboelectric nanogenerator was presented for a real-time health monitoring system. The SWS can be worn on wrists, ankles, shoes, or other parts of the body and cloth, converting mechanical triggers into electrical output. By analyzing these signals, the SWS can precisely and constantly monitor and distinguish various motion states, including stepping, walking, running, and jumping. Based on the SWS, a fall-down alarm system and a sleep quality assessment system were constructed to provide personal healthcare monitoring and alert family members or doctors via communication devices. It is important for the healthy growth of the young and special patient groups, as well as for the health monitoring and medical care of the elderly and recovered patients. This work aimed to broaden the paths for remote biological movement status analysis and provide diversified perspectives for true-time and long-term health monitoring, simultaneously.

| S-EPMC8064435 | biostudies-literature

Flexible Layered-Graphene Charge Modulation for Highly Stable Triboelectric Nanogenerator.

Project description:The continuous quest to enhance the output performance of triboelectric nanogenerators (TENGs) based on the surface charge density of the tribolayer has motivated researchers to harvest mechanical energy efficiently. Most of the previous work focused on the enhancement of negative triboelectric charges. The enhancement of charge density over positive tribolayer has been less investigated. In this work, we developed a layer-by-layer assembled multilayer graphene-based TENG to enhance the charge density by creatively introducing a charge trapping layer (CTL) Al2O3 in between the positive triboelectric layer and conducting electrode to construct an attractive flexible TENG. Based on the experimental results, the optimized three layers of graphene TENG (3L-Gr-TENG) with CTL showed a 30-fold enhancement in output power compared to its counterpart, 3L-Gr-TENG without CTL. This remarkably enhanced performance can be ascribed to the synergistic effect between the optimized graphene layers with high dielectric CTL. Moreover, the device exhibited outstanding stability after continuous operation of >2000 cycles. Additionally, the device was capable of powering 20 green LEDs and sufficient to power an electronic timer with rectifying circuits. This research provides a new insight to improve the charge density of Gr-TENGs as energy harvesters for next-generation flexible electronics.

| S-EPMC8471573 | biostudies-literature

Chicken skin based Milli Watt range biocompatible triboelectric nanogenerator for biomechanical energy harvesting.

Project description:This work reports a high-performance, low-cost, biocompatible triboelectric nanogenerator (TENG) using chicken skin (CS). The device is suitable to power wearable devices, which is critical to adapt electronics in monitoring, predicting, and treating people. It also supports sustainability by providing a cost-effective way to reduce the poultry industry's waste. It has been shown here that CS-derived biowaste is an effective means of generating tribopositive material for TENGs. The CS contains amino acid functional groups based on (Glycine, Proline, and Hydroxyproline), which are essential to demonstrate the electron-donating ability of collagen. The skin was cut into 3 × 3 cm2 and used as the raw material for fabricating the TENG device with a stacking sequence of Al/Kapton/spacing/CS/Al. The chicken skin-based TENG (CS-TENG) is characterized at different frequencies (4-14 HZ) using a damping system. The CS-TENG produces an open-circuit voltage of 123 V, short-circuit current of 20 µA and 0.2 mW/cm2 of a power density at 20 MΩ. The biocompatible CS-TENG presents ultra-robust and stable endurance performance with more than 52,000 cycles. The CS-TENG is impressively capable of scavenging energy to light up to 55 commercial light-emitting diodes (LEDs), a calculator, and to measure the physiological motions of the human body. CS-TENG is a step toward sustainable, battery-less devices or augmented energy sources, especially when using traditional power sources, such as in wearable devices, remote locations, or mobile applications is not practical or cost-effective.

| S-EPMC10287749 | biostudies-literature

Wearable Triboelectric Nanogenerator with Ground-Coupled Electrode for Biomechanical Energy Harvesting and Sensing.

Project description:Harvesting biomechanical energy for electricity as well as physiological monitoring is a major development trend for wearable devices. In this article, we report a wearable triboelectric nanogenerator (TENG) with a ground-coupled electrode. It has a considerable output performance for harvesting human biomechanical energy and can also be used as a human motion sensor. The reference electrode of this device achieves a lower potential by coupling with the ground to form a coupling capacitor. Such a design can significantly improve the TENG's outputs. A maximum output voltage up to 946 V and a short-circuit current of 36.3 μA are achieved. The quantity of the charge that transfers during one step of an adult walking reaches 419.6 nC, while it is only 100.8 nC for the separate single-electrode-structured device. In addition, using the human body as a natural conductor to connect the reference electrode allows the device to drive the shoelaces with integrated LEDs. Finally, the wearable TENG is able to perform motion monitoring and sensing, such as human gait recognition, step count and movement speed calculation. These show great application prospects of the presented TENG device in wearable electronics.

| S-EPMC10216270 | biostudies-literature

A Cantilever Beam-Based Triboelectric Nanogenerator as a Drill Pipe Transverse Vibration Energy Harvester Powering Intelligent Exploitation System

Project description:Measurement While Drilling (MWD) is the most commonly used real-time information acquisition technique in offshore intelligent drilling, its power supply has always been a concern. Triboelectric nanogenerators have been shown to harvest low-frequency vibrational energy in the environment and convert it into electricity to power small sensors and electrical devices. This work proposed a cantilever-beam-based triboelectric nanogenerator (CB-TENG) for transverse vibration energy harvesting of a drill pipe. The CB-TENG consists of two vibrators composed of spring steel with PTFE attached and Al electrodes. The structurally optimized CB-TENG can output a peak power of 2.56 mW under the vibration condition of f = 3.0 Hz and A = 50 mm, and the electrical output can be further enhanced with the increased vibration parameters. An array-type vibration energy harvester integrated with eight CB-TENGs is designed to fully adapt to the interior of the drill pipe and improve output performance. The device can realize omnidirectional vibration energy harvesting in the two-dimensional plane with good robustness. Under the typical vibration condition, the short-circuit current and the peak power can reach 49.85 μA and 30.95 mW, respectively. Finally, a series of demonstration experiments have been carried out, indicating the application prospects of the device.

| S-EPMC9185564 | biostudies-literature

Biocompatible Soft Fluidic Strain and Force Sensors for Wearable Devices.

Project description:Fluidic soft sensors have been widely used in wearable devices for human motion capturing. However, thus far, the biocompatibility of the conductive liquid, the linearity of the sensing signal, and the hysteresis between the loading and release processes have limited the sensing quality as well as the applications of these sensors. In this paper, silicone based strain and force sensors composed of a novel biocompatible conductive liquid (potassium iodide and glycerol solution) are introduced. The strain sensors exhibit negligible hysteresis up to 5 Hz, with a gauge factor of 2.2 at 1 Hz. The force sensors feature a novel multi-functional layered structure, with micro-cylinder-filled channels to achieve high linearity, low hysteresis (5.3% hysteresis at 1 Hz), and good sensitivity (100% resistance increase at a 5 N load). The sensors' gauge factors are stable at various temperatures and humidity levels. These bio-compatible, low hysteresis, and high linearity sensors are promising for safe and reliable diagnostic devices, wearable motion capture, and compliant human-computer interfaces.

| S-EPMC6675035 | biostudies-literature

Hydrogels as Soft Ionic Conductors in Flexible and Wearable Triboelectric Nanogenerators.

Project description:Flexible triboelectric nanogenerators (TENGs) have attracted increasing interest since their advent in 2012. In comparison with other flexible electrodes, hydrogels possess transparency, stretchability, biocompatibility, and tunable ionic conductivity, which together provide great potential as current collectors in TENGs for wearable applications. The development of hydrogel-based TENGs (H-TENGs) is currently a burgeoning field but research efforts have lagged behind those of other common flexible TENGs. In order to spur research and development of this important area, a comprehensive review that summarizes recent advances and challenges of H-TENGs will be very useful to researchers and engineers in this emerging field. Herein, the advantages and types of hydrogels as soft ionic conductors in TENGs are presented, followed by detailed descriptions of the advanced functions, enhanced output performance, as well as flexible and wearable applications of H-TENGs. Finally, the challenges and prospects of H-TENGs are discussed.

| S-EPMC9009134 | biostudies-literature

OmicsDI is part of the ELIXIR infrastructure

OmicsDI is an Elixir interoperability service. Learn more ›

Tweets

OmicsDI Databases

PRIDE
PeptideAtlas
MassIVE
JPOST Repository
Physiome Model Repository

EGA
EVA
ENA
LINCS
PAXDB
Cell Collective

MetaboLights
Metabolomics Workbench
MetabolomeExpress
GNPS
BioModels
FAIRDOMHub

ArrayExpress
dbGaP
ExpressionAtlas
GEO
NODE

Information

Databases
Help
API
Contact us
Code on GitHub
Terms of use
Submit Data