Dataset Information

Fermentation based carbon nanotube multifunctional bionic composites.

ABSTRACT: The exploitation of the processes used by microorganisms to digest nutrients for their growth can be a viable method for the formation of a wide range of so called biogenic materials that have unique properties that are not produced by abiotic processes. Here we produced living hybrid materials by giving to unicellular organisms the nutrient to grow. Based on bread fermentation, a bionic composite made of carbon nanotubes (CNTs) and a single-cell fungi, the Saccharomyces cerevisiae yeast extract, was prepared by fermentation of such microorganisms at room temperature. Scanning electron microscopy analysis suggests that the CNTs were internalized by the cell after fermentation bridging the cells. Tensile tests on dried composite films have been rationalized in terms of a CNT cell bridging mechanism where the strongly enhanced strength of the composite is governed by the adhesion energy between the bridging carbon nanotubes and the matrix. The addition of CNTs also significantly improved the electrical conductivity along with a higher photoconductive activity. The proposed process could lead to the development of more complex and interactive structures programmed to self-assemble into specific patterns, such as those on strain or light sensors that could sense damage or convert light stimulus in an electrical signal.

SUBMITTER: Valentini L

PROVIDER: S-EPMC4899685 | biostudies-literature | 2016 Jun

REPOSITORIES: biostudies-literature

ACCESS DATA

Publications

Fermentation based carbon nanotube multifunctional bionic composites.

Valentini Luca L Bon Silvia Bittolo SB Signetti Stefano S Tripathi Manoj M Iacob Erica E Pugno Nicola M NM

Scientific reports 20160609

The exploitation of the processes used by microorganisms to digest nutrients for their growth can be a viable method for the formation of a wide range of so called biogenic materials that have unique properties that are not produced by abiotic processes. Here we produced living hybrid materials by giving to unicellular organisms the nutrient to grow. Based on bread fermentation, a bionic composite made of carbon nanotubes (CNTs) and a single-cell fungi, the Saccharomyces cerevisiae yeast extract ...[more]

PMID: 27279425

Similar Datasets

Project description:This work aimed to monitor, through the changes in electrical resistance, the evolution of the mechanical properties due to aging caused by water sorption in carbon nanotube-based epoxy composites. The epoxy/CNT nanocomposites were prepared by dispersing the filler in the precursor through the ultra-sonication process and mixing the hardener by mechanical stirring. After an evaluation of the electrical properties, detected through a two-probe electrical measurement method, of nanocomposites at different percentages by weight of the filler (0.025, 0.05, 0.1, 0.3, 0.5, and 1.0), a concentration (0.1% by weight), close to that of the electrical percolation threshold, was chosen to evaluate the resistive response. This specific concentration was selected in order to obtain maximized values of the variation detected for the changes in the electrical resistance resulting from phenomena of structural relaxations/rearrangements due to water absorption. In particular, the electrical conductivity value switched from 8.2 × 10-14 S/m for the unfilled epoxy resin to 6.3 × 10-2 S/m for carbon nanotube-based epoxy composite at 0.1% by weight of the nanofiller. The water sorption caused a reduction in the mechanical properties (storage modulus and tan δ) due to swelling and plasticization phenomena, which caused the structural reorganization of the conductive interparticle contacts in the matrix with a consequent variation in the electrical resistance of the material. The found 'non-Fickian' water diffusion behavior was very similar to the variation in the electrical resistance with time. This last correlation allows the association of the measurement of the electrical resistance with the quantity of absorbed water and, therefore, with the aging of the material to water absorption, through the sensitivity factor (β). The resistive nature of the composite can be used to monitor the amount of water absorption and the changes in the structure of the material subject to water aging.

Project description:We present research progress made in developing copper/carbon nanotube composites (Cu/CNT) to fulfil a growing demand for lighter copper substitutes with superior electrical, thermal and mechanical performances. Lighter alternatives to heavy copper electrical and data wiring are needed in automobiles and aircrafts to enhance fuel efficiencies. In electronics, better interconnects and thermal management components than copper with higher current- and heat-stabilities are required to enable device miniaturization with increased functionality. Our literature survey encouragingly indicates that Cu/CNT performances (electrical, thermal and mechanical) reported so far rival that of Cu, proving the material's viability as a Cu alternative. We identify two grand challenges to be solved for Cu/CNT to replace copper in real-life applications. The first grand challenge is to fabricate Cu/CNT with overall performances exceeding that of copper. To address this challenge, we propose research directions to fabricate Cu/CNT closer to ideal composites theoretically predicted to surpass Cu performances (i.e. those containing uniformly distributed Cu and individually aligned CNTs with beneficial CNT-Cu interactions). The second grand challenge is to industrialize and transfer Cu/CNT from lab bench to real-life use. Toward this, we identify and propose strategies to address market-dependent issues for niche/mainstream applications. The current best Cu/CNT performances already qualify for application in niche electronic device markets as high-end interconnects. However, mainstream Cu/CNT application as copper replacements in conventional electronics and in electrical/data wires are long-term goals, needing inexpensive mass-production by methods aligned with existing industrial practices. Mainstream electronics require cheap CNT template-making and electrodeposition procedures, while data/electrical cables require manufacture protocols based on co-electrodeposition or melt-processing. We note (with examples) that initiatives devoted to Cu/CNT manufacturing for both types of mainstream applications are underway. With sustained research on Cu/CNT and accelerating its real-life application, we expect the successful evolution of highly functional, efficient, and sustainable next-generation electrical and electronics systems.

Dataset Information

Fermentation based carbon nanotube multifunctional bionic composites.

Publications

Fermentation based carbon nanotube multifunctional bionic composites.

Similar Datasets

OmicsDI is part of the ELIXIR infrastructure

Tweets