Magnetic field effects in dye-sensitized solar cells controlled by different cell architecture.
Ontology highlight
ABSTRACT:
SUBMITTER: Klein M
PROVIDER: S-EPMC4954973 | biostudies-literature |
REPOSITORIES: biostudies-literature
Similar Datasets
Project description:Over the past few decades, the field of p-type dye-sensitized solar cell (p-DSSC) devices has undergone tremendous advances, in which Cu-based delafossite nanocrystal is of prime interest. This paper presents an augment of about 87% improvement in photocurrent observed in a particular configuration of organic dye P1 sensitized CuCrO2 delafossite nanocrystal electrode coupled with organic redox shuttle, 1-methy-1H- tetrazole-5-thiolate and its disulfide dimer when Au nanoparticles (NPs, with diameter of about 20 nm) is added into the photocathode, achieving a power convert efficiency of 0.31% (measured under standard AM 1.5 G test conditions). Detailed investigation shows that the local electrical-magnetic field effect, induced by Au NPs among the mesoporous CuCrO2 film, can improve the charge injection efficiency at dye/semiconductor interface, which is responsible for the bulk of the gain in photocurrent.
| S-EPMC3912483 | biostudies-literature
Project description:A new class of dye-sensitized solar cells (DSSCs) using the hemicage cobalt-based mediator [Co(ttb)]2+/3+ with the highly preorganized hexadentate ligand 5,5'',5''''-((2,4,6-triethyl benzene-1,3,5-triyl)tris(ethane-2,1-diyl))tri-2,2'-bipyridine (ttb) has been fully investigated. The performances of DSSCs sensitized with organic D-π-A dyes utilizing either [Co(ttb)]2+/3+ or the conventional [Co(bpy)3 ]2+/3+ (bpy=2,2'-bipyridine) redox mediator are comparable under 1000 W m-2 AM 1.5 G illumination. However, the hemicage complexes exhibit exceptional stability under thermal and light stress. In particular, a 120-hour continuous light illumination stability test for DSSCs using [Co(ttb)]2+/3+ resulted in a 10 % increase in the performance, whereas a 40 % decrease in performance was found for [Co(bpy)3 ]2+/3+ electrolyte-based DSSCs under the same conditions. These results demonstrate the great promise of [Co(ttb)]2+/3+ complexes as redox mediators for efficient, cost-effective, large-scale DSSC devices.
| S-EPMC5305181 | biostudies-literature
Project description:Using density functional theory (DFT) and time-dependent density functional theory (TDDFT) methods, three porphyrin dyes with different acceptors, such as carboxylic acid, cyanoacrylic acid, and 2-cyano-N-hydroxyacrylamide, have been designed. Compared to the best sensitizer (YD2-o-C8) so far, these designed dyes have small highest occupied orbital to lowest unoccupied orbital (HOMO-LUMO) band gaps, and wide absorptions with large oscillator strength at porphyrin Q bands. And the designed Dye1 is similar to YD2-o-C8 in electronic coupling with TiO2, while improved Dye2 and Dye3 are better than YD2-o-C8, thus, Dye2 and Dye3 will be much faster for electron injection in dye-sensitized solar cell systems based on their long-term stable and efficient anchor groups. All these features show that our designed dyes, especially Dye2 and Dye3, have better absorption performance and faster electron injection. In addition, our results point out that 2-cyano-N-hydroxyacrylamide is a new promising acceptor. This study is expected to assist the molecular design of new efficient dyes for the advancement of dye-sensitized solar cells.
| S-EPMC9080764 | biostudies-literature
Project description:In this paper, an in-situ microfluidic control unit (MCU) was designed and applied in a hydrothermal synthesis process, which provides an easy way to localize liquid-phase reaction and realize selective synthesis and direct growth of nanostructures as well as their morphology, all in a low-temperature and atmospheric environment. The morphology was controlled through controlling the amount of additivities using the MCU. This achieved a facile fabrication of Al doped ZnO (AZO) nanoflakes vertically grown on flexible polymer substrates with enhanced light scattering and dye loading capabilities. Flexible DSSCs with a significant enhancement (410% compare to ZnO NRs based devices) in power conversion efficiency were obtained using AZO nanoflake photoanodes of 6 ?m thick, due to the enhancement in electron mobility and reduction in recombination. This hydrothermal synthesis using the in-situ MCU provides an efficient and scalable technique to synthesize controllable nanostructures with characteristics of easy set-up, low energy consumption and low cost.
| S-EPMC4668546 | biostudies-literature
Project description:Dye-sensitized solar cells (DSSCs) belong to the group of thin-film solar cells which have been under extensive research for more than two decades due to their low cost, simple preparation methodology, low toxicity and ease of production. Still, there is lot of scope for the replacement of current DSSC materials due to their high cost, less abundance, and long-term stability. The efficiency of existing DSSCs reaches up to 12%, using Ru(II) dyes by optimizing material and structural properties which is still less than the efficiency offered by first- and second-generation solar cells, i.e., other thin-film solar cells and Si-based solar cells which offer ~?20-30% efficiency. This article provides an in-depth review on DSSC construction, operating principle, key problems (low efficiency, low scalability, and low stability), prospective efficient materials, and finally a brief insight to commercialization.
| S-EPMC6261913 | biostudies-other
Project description:BackgroundDye-sensitized solar cells (DSSCs) have garnered a lot of attention in recent years. The solar energy to power conversion efficiency of a DSSC is influenced by various components of the cell such as the dye, electrolyte, electrodes and additives among others leading to varying experimental configurations. A large number of metal-based and metal-free dye sensitizers have now been reported and tools using such data to indicate new directions for design and development are on the rise.DescriptionDSSCDB, the first of its kind dye-sensitized solar cell database, aims to provide users with up-to-date information from publications on the molecular structures of the dyes, experimental details and reported measurements (efficiencies and spectral properties) and thereby facilitate a comprehensive and critical evaluation of the data. Currently, the DSSCDB contains over 4000 experimental observations spanning multiple dye classes such as triphenylamines, carbazoles, coumarins, phenothiazines, ruthenium and porphyrins.ConclusionThe DSSCDB offers a web-based, comprehensive source of property data for dye sensitized solar cells. Access to the database is available through the following URL: www.dyedb.com .
| S-EPMC5882482 | biostudies-literature
Project description:At an elevated temperature of 90 °C, a chemical bath deposition using an aqueous solution of Zn(NO3)2·6H2O and (CH2)6N4 resulted in the formation of both nanoflowers and microrods of ZnO on F-doped SnO2 glass with a seed layer. The nanoflowers and microrods were sensitized with dyes for application to the photoelectrodes of dye-sensitized solar cells (DSSCs). By extending the growth time of ZnO, the formation of nanoflowers was reduced and the formation of microrods favored. As the growth time was increased from 4 to 6 and then to 8 h, the open circuit voltage (Voc) values of the DSSCs were increased, whilst the short circuit current (Jsc) values varied only slightly. Changes in the dye-loading amount, dark current, and electrochemical impedance were monitored and they revealed that the increase in Voc was found to be due to a retardation of the charge recombination between photoinjected electrons and I3- ions and resulted from a reduction in the surface area of ZnO microrods. A reduced surface area decreased the dye contents adsorbed on the ZnO microrods, and thereby decreased the light harvesting efficiency (LHE). An increase in the electron collection efficiency attributed to the suppressed charge recombination counteracted the decreased LHE, resulting in comparable Jsc values regardless of the growth time.
| S-EPMC6956303 | biostudies-literature
Project description:Herein we realize an optical design that optimizes the performance of bifacial solar cells without modifying any of the usually employed components. In order to do so, dielectric scatterers of controlled size and shape have been successfully integrated in the working electrodes of dye-sensitized solar cells (DSSCs), resulting in bifacial devices of outstanding performance. Power conversion efficiencies (PCEs) as high as 6.7% and 5.4% have been attained under front and rear illumination, respectively, which represent a 25% and a 33% PCE enhancement with respect to an 8 μm-thick standard solar cell electrode using platinum as the catalytic material. The remarkable bifacial character of our approach is demonstrated by the high rear/front efficiency ratio attained, around 80%, which is among the largest reported for this sort of device. The proposed optimized design is based on a Monte Carlo approach in which the multiple scattering of light within the cell is fully accounted for. We identified that the spherical shape of the scatterers is the key parameter controlling the angular distribution of the scattering, the most efficient devices being those in which the inclusions provide a narrow forward-oriented angular distribution of the scattered light.
| S-EPMC4786952 | biostudies-literature
Project description:The effect of TiO2 nanostructures such as nanoparticles, nanowires, nanotubes on photoanode properties, and dye-sensitized solar cells photovoltaic parameters were studied. The series of dye-sensitized solar cells based on two dyes, that is, commercially N719 and synthesized 3,7'-bis(2-cyano-1-acrylic acid)-10-ethyl-phenothiazine were tested. Additionally, the devices containing a mixture of this sensitizer and chenodeoxycholic acid as co-adsorbent were fabricated. The amount of adsorbed dye molecules to TiO2 was evaluated. The prepared photoanodes with different TiO2 nanostructures were investigated using UV-Vis spectroscopy, optical, atomic force, and scanning electron microscopes. Photovoltaic response of constructed devices was examined based on current-voltage characteristics and electrochemical impedance spectroscopy measurements. It was found that the highest UV-Vis absorption exhibited the photoanode with nanotubes addition. This indicates the highest number of sensitizer molecules anchored to the titanium dioxide photoanode, which was subsequently confirmed by dye-loading tests. The highest power conversion efficiency was (6.97%) for solar cell containing nanotubes and a mixture of the dyes with a co-adsorbent.
| S-EPMC8036646 | biostudies-literature
Project description:Herein we report an experimental analysis of the performance of photonic crystal based dye solar cells (PC-DSCs) as the incident light angle moves away from the normal with respect to the cell surface. Nanoparticle multilayers operating at different wavelength ranges were coupled to the working electrode of a dye solar cell for this study. The interplay between optical and photovoltaic properties with the incident light angle is discussed. We demonstrate that an efficiency enhancement is attained for PC-DSCs at all angles measured, and that rational design of the photonic crystal back mirror leads to a reduction of the photocurrent losses related to the tilt angle of the cell, usually labeled as cosine losses. Angular variations of the cell transparency are also reported and discussed. These angular properties are relevant to the application of these solar devices in building integrated photovoltaics as potential window modules.
| S-EPMC4535183 | biostudies-literature