Bamboo-inspired optimal design for functionally graded hollow cylinders.
Ontology highlight
ABSTRACT:
SUBMITTER: Sato M
PROVIDER: S-EPMC5414991 | biostudies-literature | 2017
REPOSITORIES: biostudies-literature
Publications
Bamboo-inspired optimal design for functionally graded hollow cylinders.
Sato Motohiro M Inoue Akio A Shima Hiroyuki H
PloS one 20170503 5
The optimal distribution of the reinforcing fibers for stiffening hollow cylindrical composites is explored using the linear elasticity theory. The spatial distribution of the vascular bundles in wild bamboo, a nature-designed functionally graded material, is the basis for the design. Our results suggest that wild bamboos maximize their flexural rigidity by optimally regulating the radial gradation of their vascular bundle distribution. This fact provides us with a plant-mimetic design principle ...[more]
Similar Datasets
Project description:Synthetic fibrillar adhesives inspired by nature, most commonly by the gecko lizard, have been shown to strongly and repeatedly attach to smooth surfaces. These adhesives, mostly of monolithic construction, perform on par with their natural analogues on smooth surfaces but exhibit far inferior adhesive performance on rough surfaces. In this paper, we report on the adhesive performance of functionally graded microfibrillar adhesives based on a microfibre with a divergent end and a thin soft distal layer on rough surfaces. Monolithic and functionally graded fibre arrays were fabricated from polyurethanes and their adhesive performance on surfaces of varying roughness were quantified from force-distance data obtained using a custom adhesion measurement system. Average pull-off stress declined significantly with increasing roughness for the monolithic fibre array, dropping from 77?kPa on the smoothest (54?nm RMS roughness) to 19?kPa on the roughest (408?nm RMS roughness) testing surface. In comparison, pull-off stresses of 81?kPa and 63?kPa were obtained on the same respective smooth and rough surfaces with a functionally graded fibre array, which represents a more than threefold increase in adhesion to the roughest adhering surface. These results show that functionally graded fibrillar adhesives perform similar on all the testing surfaces unlike monolithic arrays and show potential as repeatable and reusable rough surface adhesives.
| S-EPMC5493905 | biostudies-literature
Project description:This article is concerned with the theoretical analysis of the functionally graded magneto-electro-thermoelastic hollow sphere due to uniform surface heating. We analyze the transient thermoelastic problem for a functionally graded hollow sphere constructed of the spherical isotropic and linear magneto-electro-thermoelastic materials using a laminated composite mode as one of theoretical approximation in the spherically symmetric state. As an illustration, we carry out numerical calculations for a functionally graded hollow sphere constructed of piezoelectric and magnetostrictive materials and examine the behaviors in the transient state. The effects of the nonhomogeneity of material on the stresses, electric potential, and magnetic potential are investigated.
| S-EPMC5448889 | biostudies-other
Project description:The functional gradient is a concept often occurring in nature. This concept can be implemented in the design and fabrication of advanced materials with specific functionalities and properties. Functionally graded materials (FGMs) can effectively eliminate the interface problems in extremely hard-soft connections, and, thus, have numerous and diverse applications in high-tech industries, such as those in biomedical and aerospace fields. Here, using voxel-based multi-material additive manufacturing (AM, = 3D printing) techniques, which works on the basis of material jetting, we studied the fracture behavior of functionally graded soft-hard composites with a pre-existing crack colinear with the gradient direction. We designed, additively manufactured, and mechanically tested the two main types of functionally graded composites, namely, composites with step-wise and continuous gradients. In addition, we changed the length of the transition zone between the hard and soft materials such that it covered 5%, 25%, 50%, or 100% of the width (W) of the specimens. The results showed that except for the fracture strain, the fracture properties of the graded specimens decreased as the length of the transition zone increased. Additionally, it was found that specimens with abrupt hard-soft transitions have significantly better fracture properties than those with continuous gradients. Among the composites with gradients, those with step-wise gradients showed a slightly better fracture resistance compared to those with continuous gradients. In contrast, FGMs with continuous gradients showed higher values of elastic stiffness and fracture energy, which makes each gradient function suitable for different loading scenarios. Moreover, regardless of the gradient function used in the design of the specimens, decreasing the length of the transition zone from 100%W to 5%W increased the fracture resistance of FGMs. We discuss the important underlying fracture mechanisms using data collected from digital image correlation (DIC), digital image microscopy, and scanning electron microscopy (SEM), which were used to analyze the fracture surface.
| S-EPMC6747772 | biostudies-literature
Project description:The immunogenicity of biotherapeutics can bottleneck development pipelines and poses a barrier to widespread clinical application. As a result, there is a growing need for improved deimmunization technologies. We have recently described algorithms that simultaneously optimize proteins for both reduced T cell epitope content and high-level function. In silico analysis of this dual objective design space reveals that there is no single global optimum with respect to protein deimmunization. Instead, mutagenic epitope deletion yields a spectrum of designs that exhibit tradeoffs between immunogenic potential and molecular function. The leading edge of this design space is the Pareto frontier, i.e. the undominated variants for which no other single design exhibits better performance in both criteria. Here, the Pareto frontier of a therapeutic enzyme has been designed, constructed, and evaluated experimentally. Various measures of protein performance were found to map a functional sequence space that correlated well with computational predictions. These results represent the first systematic and rigorous assessment of the functional penalty that must be paid for pursuing progressively more deimmunized biotherapeutic candidates. Given this capacity to rapidly assess and design for tradeoffs between protein immunogenicity and functionality, these algorithms may prove useful in augmenting, accelerating, and de-risking experimental deimmunization efforts.
| S-EPMC4288714 | biostudies-literature
Project description:Ceramic prostheses often fail from fracture and wear. We hypothesize that these failures may be substantially mitigated by an appropriate grading of elastic modulus at the ceramic surface. In this study, we elucidate the effect of elastic modulus profile on the flexural damage resistance of functionally graded materials (FGMs), providing theoretical guidelines for designing FGMs with superior load-bearing property. The Young's modulus of the graded structure is assumed to vary in a power-law relation with a scaling exponent n; this is in accordance with experimental observations from our laboratory and elsewhere. Based on the theory for bending of graded beams, we examine the effect of n value and bulk-to-surface modulus ratio (E(b)/E(s)) on stress distribution through the graded layer. Theory predicts that a low exponent (0.15<n<0.5), coupled with a relatively small modulus ratio (3<E(b)/E(s)<6), is most desirable for reducing the maximum stress and transferring it into the interior, while keeping the surface stress low. Experimentally, we demonstrate that elastically graded materials with various n values and E(b)/E(s) ratios can be fabricated by infiltrating alumina and zirconia with a low-modulus glass. Flexural tests show that graded alumina and zirconia with suitable values of these parameters exhibit superior load-bearing capacity, 20-50% higher than their homogeneous counterparts. Improving load-bearing capacity of ceramic materials could have broad impacts on biomedical, civil, structural, and an array of other engineering applications.
| S-EPMC3272119 | biostudies-literature
Project description:Functionally graded materials (FGMs) are compositionally gradient materials. They can achieve the controlled distribution of the desired characteristics within the same bulk material. We describe a functionally graded (FG) metal-phosphor adapting the concept of the FGM; copper (Cu) is selected as a metal and Cu- and Cl-doped ZnS (ZnS:Cu,Cl) is selected as a phosphor and FG [Cu]-[ZnS:Cu,Cl] is fabricated by a very simple powder process. The FG [Cu]-[ZnS:Cu,Cl] reveals a dual-structured functional material composed of dense Cu and porous ZnS:Cu,Cl, which is completely combined through six graded mediating layers. The photoluminescence (PL) of FG [Cu]-[ZnS:Cu,Cl] is insensitive to temperature change. FG [Cu]-[ZnS:Cu,Cl] also exhibits diode characteristics and photo reactivity for 365?nm -UV light. Our FG metal-phosphor concept can pave the way to simplified manufacturing of low-cost and can be applied to various electronic devices.
| S-EPMC4789794 | biostudies-literature
Project description:As a promising actuating material, liquid crystal elastomer (LCE) has been intensively explored in building diverse active structures and devices. Recently, direct ink writing technique has been developed to print LCE structures with various geometries and actuation behaviors. Despite the advancement in printing LCE, it remains challenging to print three-dimensional (3D) LCE structures with graded properties. Here, we report a facile method to tailor both the actuation behavior and mechanical properties of printed LCE filaments by varying printing parameters. On the basis of the comprehensive processing-structure-property relationship, we propose a simple strategy to print functionally graded LCEs, which greatly increases the design space for creating active morphing structures. We further demonstrate mitigation of stress concentration near the interface between an actuatable LCE tube and a rigid glass plate through gradient printing. The strategy developed here will facilitate potential applications of LCEs in different fields.
| S-EPMC7518867 | biostudies-literature
Project description:The curved space-time produced by black holes leads to the intriguing trapping effect. So far, metadevices have enabled analogous black holes to trap light or sound in laboratory spacetime. However, trapping heat in a conductive environment is still challenging because diffusive behaviors are directionless. Inspired by black holes, we construct graded heat-conduction metadevices to achieve thermal trapping, resorting to the imitated advection produced by graded thermal conductivities rather than the trivial solution of using insulation materials to confine thermal diffusion. We experimentally demonstrate thermal trapping for guiding hot spots to diffuse towards the center. Graded heat-conduction metadevices have advantages in energy-efficient thermal regulation because the imitated advection has a similar temperature field effect to the realistic advection that is usually driven by external energy sources. These results also provide an insight into correlating transformation thermotics with other disciplines, such as cosmology, for emerging heat control schemes.
| S-EPMC10016200 | biostudies-literature
Project description:Osteochondral tissue repair remains a significant challenge in orthopedic surgery. Tissue engineering of osteochondral tissue has transpired as a potential therapeutic solution as it can effectively regenerate bone, cartilage, and the bone-cartilage interface. While advancements in scaffold fabrication and stem cell engineering have made significant progress towards the engineering of composite tissues, such as osteochondral tissue, new approaches are required to improve the outcome of such strategies. Herein, we discuss the use of a single-unit trilayer scaffold with depth-varying pore architecture and mineral environment to engineer osteochondral tissues in vivo. The trilayer scaffold includes a biomineralized bottom layer mimicking the calcium phosphate (CaP)-rich bone microenvironment, a cryogel middle layer with anisotropic pore architecture, and a hydrogel top layer. The mineralized bottom layer was designed to support bone formation, while the macroporous middle layer and hydrogel top layer were designed to support cartilage tissue formation. The bottom layer was kept acellular and the top two layers were loaded with cells prior to implantation. When implanted in vivo, these trilayer scaffolds resulted in the formation of osteochondral tissue with a lubricin-rich cartilage surface. The osteochondral tissue formation was a result of continuous differentiation of the transplanted cells to form cartilage tissue and recruitment of endogenous cells through the mineralized bottom layer to form bone tissue. Our results suggest that integrating exogenous cell-based cartilage tissue engineering along with scaffold-driven in situ bone tissue engineering could be a powerful approach to engineer analogs of osteochondral tissue. In addition to offering new therapeutic opportunities, such approaches and systems could also advance our fundamental understanding of osteochondral tissue regeneration and repair. STATEMENT OF SIGNIFICANCE:In this work, we describe the use of a single-unit trilayer scaffold with depth-varying pore architecture and mineral environment to engineer osteochondral tissues in vivo. The trilayer scaffold was designed to support continued differentiation of the donor cells to form cartilage tissue while supporting bone formation through recruitment of endogenous cells. When implanted in vivo, these trilayer scaffolds partially loaded with cells resulted in the formation of osteochondral tissue with a lubricin-rich cartilage surface. Approaches such as the one presented here that integrates ex vivo tissue engineering along with endogenous cell-mediated tissue engineering can have a significant impact in tissue engineering composite tissues with diverse cell populations and functionality.
| S-EPMC6309375 | biostudies-literature
Project description:Functionally graded soft materials (FGSMs) with microstructures and mechanical properties exhibiting gradients across a spatial volume to satisfy specific functions have received interests in recent years. How to characterize the mechanical properties of these FGSMs in vivo/in situ and/or in a non-destructive manner is a great challenge. This paper investigates the use of ultrasound elastography in the mechanical characterization of FGSMs. An efficient finite-element model was built to calculate the dispersion relation for surface waves in FGSMs. For FGSMs with large elastic gradients, the measured dispersion relation can be used to identify mechanical parameters. In the case where the elastic gradient is smaller than a certain critical value calculated here, our analysis on transient wave motion in FGSMs shows that the group velocities measured at different depths can infer the local mechanical properties. Experiments have been performed on polyvinyl alcohol (PVA) cryogel to demonstrate the usefulness of the method. Our analysis and the results may not only find broad applications in mechanical characterization of FGSMs but also facilitate the use of shear wave elastography in clinics because many diseases change the local elastic properties of soft tissues and lead to different material gradients. This article is part of the theme issue 'Rivlin's legacy in continuum mechanics and applied mathematics'.
| S-EPMC6452040 | biostudies-literature