Dataset Information

Fluoride ion adsorption onto palm stone: Optimization through response surface methodology, isotherm, and adsorbent characteristics data.

ABSTRACT: In some part of the world, groundwater source can become unsafe for drinking due to the high concentration of fluoride ions [1]. The low cost and facile-produced adsorbent like palm stone could effectively removed fluoride ions through adsorption process. In this dataset, the influence of fluoride ion concentration, solution pH, adsorbent dosage, and contact time on fluoride ion adsorption by palm stones was tested by central composite design (CCD) under response surface methodology (RSM). The data stone carbonized adsorbent was prepared by a simple and facile method at relatively low temperature of 250 °C during 3 h. The adsorbent had the main functional groups of O-H, -OH, Si-H, C=O, N=O, C-C, C-OR, C-H, and C-Br on its surface. At the optimized conditions obtained by RSM, about 84.78% of fluoride ion was removed using the adsorbent. The Langmuir isotherm was suitable for correlation of equilibrium data (maximum adsorption capacity= 3.95 mg/g). Overall, the data offer a facile adsorbent to water and wastewater works which face to high level of fluoride water/ wastewater content.

SUBMITTER: Ravanipour M

PROVIDER: S-EPMC5423305 | biostudies-literature | 2017 Jun

REPOSITORIES: biostudies-literature

ACCESS DATA

Publications

Fluoride ion adsorption onto palm stone: Optimization through response surface methodology, isotherm, and adsorbent characteristics data.

Ravanipour Masoumeh M Kafaei Raheleh R Keshtkar Mozhgan M Tajalli Soghra S Mirzaei Narjes N Ramavandi Bahman B

Data in brief 20170429

In some part of the world, groundwater source can become unsafe for drinking due to the high concentration of fluoride ions [1]. The low cost and facile-produced adsorbent like palm stone could effectively removed fluoride ions through adsorption process. In this dataset, the influence of fluoride ion concentration, solution pH, adsorbent dosage, and contact time on fluoride ion adsorption by palm stones was tested by central composite design (CCD) under response surface methodology (RSM). The d ...[more]

PMID: 28508026

Similar Datasets

Project description:Oil palm trunk (OPT) represents one of the five main oil palm biomass wastes with high carbon content that can be economically converted to a large surface area, porous activated carbon (AC) adsorbent to treat palm oil mill effluent wastewater in Indonesia and Malaysia. In the first portion of this work, the design of the experiment was used to determine the optimum set of synthesis parameters required to maximize the iodine number of AC [i.e., Brunauer-Emmett-Teller (BET) specific surface area indicator] prepared from OPT via chemical activation route using H3PO4. The iodine numbers of AC and AC yield were probed as the impregnation ratio, the activation time, and the activation temperature were varied in the range of 0.28-3.47, 5.68-69.32 min, and 379-521 °C, respectively. An impregnation ratio of 2.29, an activation time of 6 min, and an activation temperature of 450 °C were identified as the optimum set of synthesis parameters. In the second portion of the work, the AC synthesized using the optimum parameters were then characterized and tested as an adsorbent for tannin. N2 sorption results revealed that the AC exhibits type IV isotherm, that is, contains micropores and mesopores and displays a relatively high BET specific surface area of 1657 m2 g-1. Adsorption equilibria isotherms for tannin adsorption onto the AC were collected at three different pH of 2, 4, and 6 and were nonlinearly fitted using Langmuir and Freundlich isotherm models, where the Langmuir isotherm gave better fitting than Freundlich. The higher adsorption capacity at lower pH can be explained in terms of the absence of electrostatic repulsion interaction between the AC surface and the tannic acid species as suggested by the point of zero charges (pHpzc) of 4.8 and an increasing ionization of tannic acid with pH rise between 4 and 7. Adsorption kinetics data were also obtained at four different pH of 2, 4, 6, and 8 where the nonlinear pseudo-first-order model best fitted the kinetic at pH of 2 and the nonlinear pseudo-second-order model represented the kinetic best at the remaining higher pH, which suggests that tannin adsorption onto AC occurred by physisorption at pH of 2 and by chemisorption at pH of 4, 6, and 8.

Dataset Information

Fluoride ion adsorption onto palm stone: Optimization through response surface methodology, isotherm, and adsorbent characteristics data.

Publications

Fluoride ion adsorption onto palm stone: Optimization through response surface methodology, isotherm, and adsorbent characteristics data.

Similar Datasets

OmicsDI is part of the ELIXIR infrastructure

Tweets