Dataset Information

The Generation Rate of Respirable Dust from Cutting Fiber Cement Siding Using Different Tools.

ABSTRACT: This article describes the evaluation of the generation rate of respirable dust (GAPS, defined as the mass of respirable dust generated per unit linear length cut) from cutting fiber cement siding using different tools in a laboratory testing system. We used an aerodynamic particle sizer spectrometer (APS) to continuously monitor the real-time size distributions of the dust throughout cutting tests when using a variety of tools, and calculated the generation rate of respirable dust for each testing condition using the size distribution data. The test result verifies that power shears provided an almost dust-free operation with a GAPS of 0.006 g m-1 at the testing condition. For the same power saws, the cuts using saw blades with more teeth generated more respirable dusts. Using the same blade for all four miter saws tested in this study, a positive linear correlation was found between the saws' blade rotating speed and its dust generation rate. In addition, a circular saw running at the highest blade rotating speed of 9068 rpm generated the greatest amount of dust. All the miter saws generated less dust in the 'chopping mode' than in the 'chopping and sliding' mode. For the tested saws, GAPS consistently decreased with the increases of the saw cutting feed rate and the number of board in the stack. All the test results point out that fewer cutting interactions between the saw blade's teeth and the siding board for a unit linear length of cut tend to result in a lower generation rate of respirable dust. These results may help guide optimal operation in practice and future tool development aimed at minimizing dust generation while producing a satisfactory cut.

SUBMITTER: Qi C

PROVIDER: S-EPMC5450797 | biostudies-literature | 2017 Mar

REPOSITORIES: biostudies-literature

ACCESS DATA

Publications

The Generation Rate of Respirable Dust from Cutting Fiber Cement Siding Using Different Tools.

Qi Chaolong C Echt Alan A Gressel Michael G MG

Annals of work exposures and health 20170301 2

This article describes the evaluation of the generation rate of respirable dust (GAPS, defined as the mass of respirable dust generated per unit linear length cut) from cutting fiber cement siding using different tools in a laboratory testing system. We used an aerodynamic particle sizer spectrometer (APS) to continuously monitor the real-time size distributions of the dust throughout cutting tests when using a variety of tools, and calculated the generation rate of respirable dust for each test ...[more]

PMID: 28395343

Similar Datasets

Project description:BackgroundThe characteristics of coal dust (CD) particles affect the inhalation of CD, which causes coal worker's pneumoconiosis (CWP). CD nanoparticles (CD-NPs, < 500 nm) and micron particles (CD-MPs, < 5 μm) are components of the respirable CD. However, the differences in physicochemical properties and pulmonary toxicity between CD-NPs and CD-MPs remain unclear.MethodsCD was analyzed by scanning electron microscopy, Malvern nanoparticle size potentiometer, energy dispersive spectroscopy, infrared spectroscopy, and electron paramagnetic resonance spectroscopy. CCK-8 assay, ELISA, transmission electron microscope, JC-1 staining, reactive oxygen species activity probe, calcium ion fluorescent probe, AO/EB staining, flow cytometry, and western blot were used to determine the differences between CD-NPs and CD-MPs on acute pulmonary toxicity. CCK-8, scratch healing and Transwell assay, hematoxylin-eosin and Masson staining, immunohistochemistry, immunofluorescence, and western blot were applied to examine the effects of CD-NPs and CD-MPs on pneumoconiosis.ResultsAnalysis of the size distribution of CD revealed that the samples had been size segregated. The carbon content of CD-NPs was greater than that of CD-MPs, and the oxygen, aluminum, and silicon contents were less. In in vitro experiments with A549 and BEAS-2B cells, CD-NPs, compared with CD-MPs, had more inflammatory vacuoles, release of pro-inflammatory cytokines (IL-6, IL-1β, TNFα) and profibrotic cytokines (CXCL2, TGFβ1), mitochondrial damage (reactive oxygen species and Ca2+ levels and decreased mitochondrial membrane potential), and cell death (apoptosis, pyroptosis, and necrosis). CD-NPs-induced fibrosis model cells had stronger proliferation, migration, and invasion than did CD-MPs. In in vivo experiments, lung coefficient, alveolar inflammation score, and lung tissue fibrosis score (mean: 1.1%, 1.33, 1.33) of CD-NPs were higher than those of CD-MPs (mean: 1.3%, 2.67, 2.67). CD-NPs accelerated the progression of pulmonary fibrosis by upregulating the expression of pro-fibrotic proteins and promoting epithelial-mesenchymal transition. The regulatory molecules involved were E-cadherin, N-cadherin, COL-1, COL-3, ZO-1, ZEB1, Slug, α-SMA, TGFβ1, and Vimentin.ConclusionsStimulation with CD-NPs resulted in more pronounced acute and chronic lung toxicity than did stimulation with CD-MPs. These effects included acute inflammatory response, mitochondrial damage, pyroptosis, and necrosis, and more pulmonary fibrosis induced by epithelial-mesenchymal transition.

Project description:ObjectivesExposures to respirable crystalline silica (RCS) and respirable dust (RD) were investigated during demolition, crushing, and chipping at several Massachusetts construction sites.MethodsPersonal breathing zone samples (n = 51) were collected on operating engineers working at demolition and crushing sites, laborers performing miscellaneous tasks at demolition sites, crushing machine tenders at crushing sites, and chipping workers at substructure bridge repair sites. Area samples (n = 33) were collected at the perimeter of demolition and crushing sites to assess potential bystanders' exposures. Exposures 'with' and 'without' the use of dust suppression methods were compared when possible. RD samples were analyzed for crystalline silica content with Fourier Transform Infrared Spectrophotometry (FT-IR) according to the National Institute for Occupational Safety and Health (NIOSH) Method 7602. Statistical analyses of the exposure data were performed in SAS version 9.4.ResultsChipping workers had the highest exposure levels [the geometric mean (GM) time-weighted average (TWA) for RCS was 527 µg/m3 and the GM for RD was 4750 µg/m3]. The next highest exposures were among crushing machine tenders (RCS GM of 93.3 µg/m3 and RD GM of 737.6 µg/m3), while laborers and operating engineers had the lowest exposures (RCS GM of 17.0 and 6.2 µg/m3, respectively). Personal 8-h TWA RCS exposures were higher than the new OSHA permissible exposure limit (PEL) of 50 µg/m3 for 80% of samples collected on chipping workers (n = 31) and 50% of samples collected on crushing machine tenders (n = 8). Operating engineers (n = 9) and laborers (n = 3) had RCS exposures lower than OSHA PEL. The highest concentrations measured would have exceeded the PEL within 15 min chipping and within 2 h of crushing with no further exposure. Chipping workers' RCS exposures were higher than OSHA PEL even when they were adjusted to account for the assigned protection factor of the half-face N95 cartridge respirators used during chipping. Exposures of crushing tenders were reduced to levels under the OSHA PEL when a water spraying system in crushing machines was utilized, but not when a water cannon machine was used. Area samples at demolition and crushing sites indicate overall lower exposures than the PEL, however, bystander workers at crushing sites could be exposed to higher levels compared to demolition sites. Real-time dust monitoring during demolition indicate very high short-term peak exposures.ConclusionsControlling or reducing crystalline silica exposures to levels under the new OSHA PEL of 50 µg/m3 remains challenging for chipping workers and crushing machine tenders. Even with the use of dust suppression controls, respiratory protection may be required for various tasks.

Project description:In order to help reduce silicosis in miners, the National Institute for Occupational Health and Safety (NIOSH) is developing field-portable methods for measuring airborne respirable crystalline silica (RCS), specifically the polymorph α-quartz, in mine dusts. In this study we demonstrate the feasibility of end-of-shift measurement of α-quartz using a direct-on-filter (DoF) method to analyze coal mine dust samples deposited onto polyvinyl chloride filters. The DoF method is potentially amenable for on-site analyses, but deviates from the current regulatory determination of RCS for coal mines by eliminating two sample preparation steps: ashing the sampling filter and redepositing the ash prior to quantification by Fourier transform infrared (FT-IR) spectrometry. In this study, the FT-IR spectra of 66 coal dust samples from active mines were used, and the RCS was quantified by using: (1) an ordinary least squares (OLS) calibration approach that utilizes standard silica material as done in the Mine Safety and Health Administration's P7 method; and (2) a partial least squares (PLS) regression approach. Both were capable of accounting for kaolinite, which can confound the IR analysis of silica. The OLS method utilized analytical standards for silica calibration and kaolin correction, resulting in a good linear correlation with P7 results and minimal bias but with the accuracy limited by the presence of kaolinite. The PLS approach also produced predictions well-correlated to the P7 method, as well as better accuracy in RCS prediction, and no bias due to variable kaolinite mass. Besides decreased sensitivity to mineral or substrate confounders, PLS has the advantage that the analyst is not required to correct for the presence of kaolinite or background interferences related to the substrate, making the method potentially viable for automated RCS prediction in the field. This study demonstrated the efficacy of FT-IR transmission spectrometry for silica determination in coal mine dusts, using both OLS and PLS analyses, when kaolinite was present.

Dataset Information

The Generation Rate of Respirable Dust from Cutting Fiber Cement Siding Using Different Tools.

Publications

The Generation Rate of Respirable Dust from Cutting Fiber Cement Siding Using Different Tools.

Similar Datasets

OmicsDI is part of the ELIXIR infrastructure

Tweets