Modulating the Optoelectronic Properties of Silver Nanowires Films: Effect of Capping Agent and Deposition Technique.
Ontology highlight
ABSTRACT:
SUBMITTER: Lopez-Diaz D
PROVIDER: S-EPMC5458922 | biostudies-literature |
REPOSITORIES: biostudies-literature
Similar Datasets
Project description:Silver nanowires (AgNWs) show promise for fabricating flexible transparent conductors owing to their excellent conductivity, high transparency, and good mechanical properties. Here, we present the fabrication of transparent films composed of AgNWs with diameters of 20-30 nm and lengths of 25-30 μm on polyethylene terephthalate substrates and glass slides substrates using the Meyer rod method. We systematically investigated the films' optoelectronic and electrothermal properties. The morphology remained intact when heated at 25-150 °C and the AgNWs film showed high conductivity (17.6-14.3 Ω∙sq-1), excellent transmittance (93.9-91.8%) and low surface roughness values (11.2-14.7 nm). When used as a heater, the transparent AgNW conductive film showed rapid heating at low input voltages owing to a uniform heat distribution across the whole substrate surface. Additionally, the conductivity of the film decreased with increasing bending cycle numbers; however, the film still exhibited a good conductivity and heating performances after repeated bending.
| S-EPMC6631837 | biostudies-other
Project description:Robust, high-strength and environmentally friendly antibacterial composite films were prepared by simply blending konjac glucomannan (KGM) and silver nanowires (Ag NWs) in an aqueous system. The samples were then characterized using scanning electron microscopy (SEM), X-ray diffraction (XRD), thermal gravimetric analysis, mechanical property tests, Fourier transform infrared spectra (FT-IR), X-ray photoelectron spectroscopy (XPS) and antimicrobial tests. The results showed that there was a high ratio of Ag NWs uniformly distributed in the composite films, which was vital for mechanical reinforcement and stable antibacterial properties. The enhanced thermal stability and mechanical intensity increased, while the elongation at break was reduced with an increase in the amount of Ag NWs found in the composite films. When the percentage of Ag NWs in the composite films reached 5%, the tensile strength was 148.21 MPa, Young's modulus was 13.79 GPa and the ultimate strain was 25.28%. Antibacterial tests showed that the KGM films had no antibacterial effect. After the addition of Ag NWs, the composite films had an obvious inhibitory effect on bacteria, with the uniform dispersion of Ag NWs promoting the antibacterial effect to a certain degree. These results indicated that these composite films would have a potential application in the fields of environmentally friendly packaging or medicine.
| S-EPMC5459029 | biostudies-other
Project description:Gallium oxide is a wide-bandgap compound semiconductor material renowned for its diverse applications spanning gas sensors, liquid crystal displays, transparent electrodes, and ultraviolet detectors. This paper details the aerosol assisted chemical vapor deposition synthesis of tin doped gallium oxide thin films using gallium acetylacetonate and monobutyltin trichloride dissolved in methanol. It was observed that Sn doping resulted in a reduction in the transmittance of Ga2O3 films within the visible spectrum, while preserving the wide bandgap characteristics of 4.8 eV. Furthermore, Hall effect testing revealed a substantial decrease in the resistivity of Sn-doped Ga2O3 films, reducing it from 4.2 × 106 Ω cm to 2 × 105 Ω cm for the 2.5 at. % Sn:Ga2O3 compared to the nominally undoped Ga2O3.
| S-EPMC11360363 | biostudies-literature
Project description:Silver nanowires are used in many applications, ranging from transparent conductive layers to Raman substrates and sensors. Their performance often relies on their unique optical properties that emerge from localized surface plasmon resonances in the ultraviolet. To tailor the nanowire geometry for a specific application, a correct understanding of the relationship between the wire's structure and its optical properties is therefore necessary. However, while the colloidal synthesis of silver nanowires typically leads to structures with pentagonally twinned geometries, their optical properties are often modeled assuming a cylindrical cross-section. Here we highlight the strengths and limitations of such an approximation by numerically calculating the optical and electrical response of pentagonally twinned silver nanowires and nanowire networks. We find that our accurate modeling is crucial to deduce structural information from experimentally measured extinction spectra of colloidally synthesized nanowire suspensions and to predict the performance of nanowire-based near-field sensors. On the contrary, the cylindrical approximation is fully capable of capturing the optical and electrical performance of nanowire networks used as transparent electrodes. Our results can help assess the quality of nanowire syntheses and guide in the design of optimized silver nanowire-based devices.
| S-EPMC9150108 | biostudies-literature
Project description:Silver nanowires have attracted much attention for use in flexible transparent conductive films (TCFs) due to their low sheet resistance and flexibility. However, the haze was too high for replacing indium-tin-oxide in high-quality display devices. Herein, we report flexible TCFs, which were prepared using a scalable bar-coating method, with a low sheet resistance (24.1 ?/sq at 96.4% transmittance) and a haze (1.04%) that is comparable to that of indium-tin-oxide TCFs. To decrease the haze and maintain a low sheet resistance, small diameter silver nanowires (~20 nm) were functionalized with low-temperature surface-sintering silver nanoparticles (~5 nm) using bifunctional cysteamine. The silver nanowire-nanoparticle ink stability was excellent. The sheet resistance of the TCFs was decreased by 29.5% (from 34.2 to 24.1 ?/sq) due to the functionalization at a low curing temperature of 85?°C. The TCFs were highly flexible and maintained their stability for more than 2 months and 10,000 bending cycles after coating with a protective layer.
| S-EPMC4648094 | biostudies-literature
Project description:The inkjet printing process is a promising electronic printing technique for large-scale, printed, flexible and stretchable electronics because of features such as its high manufacturing speed, environmental friendliness, simple process, low cost, accurate positioning, and so on. As the base material of printed conductive patterns, conductive ink is the foundation of the development of printed electronics technology, and directly affects the performance and the quality of electronic products. In this paper, conductive ink with silver nanowires (AgNWs) was prepared, with AgNWs of lengths of 2-5 µm and diameters of 20 nm or so, isopropyl alcohol and ethylene glycol as the mixed solvents, and modified polysilane as the wetting agent. We discussed the relationship between the formula of the AgNWs ink and the surface tension, viscosity, contact angle between ink droplet and poly(ethylene) terephthalate (PET) surface, as well as the film-forming properties of the ink. Further, we analyzed the effects of the number of printed layers and the ink concentration of the AgNWs on the microstructures, photoelectric properties and accuracy of the printed patterns, as well as the change in the sheet resistance of the film during different bending cycles. The experimental results show that flexible transparent conductive patterns with a light transmittance of 550 nm of 83.1-88.4% and a sheet resistance of 34.0 Ω∙sq-1-78.3 nm∙sq-1 can be obtained by using AgNWs ink of 0.38 mg∙mL-1 to 0.57 mg∙mL-1, a poly (ethylene terephthalate) (PET) substrate temperature of 40 °C, a nozzle temperature of 35 °C, and heat treated at 60 °C for 10 min. These performances indicate the excellent potential of the inkjet printing of AgNWs networks for developing flexible transparent conductive film.
| S-EPMC8232118 | biostudies-literature
Project description:Silver nanowire (AgNWs) inks for inkjet printing were prepared and the effects of the solvent system, wetting agent, AgNWs suspension on the viscosity, surface tension, contact angle between ink droplet and poly(ethylene) terephthalate (PET) surface, and pH value of AgNWs ink were discussed. Further, AgNWs flexible transparent conductive films were fabricated by using inkjet printing process on the PET substrate, and the effects of the number printing layer, heat treatment temperature, drop frequency, and number of nozzle on the microstructures and photoelectric properties of AgNWs films were investigated in detail. The experimental results demonstrated that the 14-layer AgNWs printed film heated at 60 °C and 70 °C had an average sheet resistance of 13 Ω∙sq-1 and 23 Ω∙sq-1 and average transparency of 81.9% and 83.1%, respectively, and displayed good photoelectric performance when the inkjet printing parameters were set to the voltage of 20 V, number of nozzles of 16, drop frequency of 7000 Hz, droplet spacing of 15 μm, PET substrate temperatures of 40 °C and nozzles of 35 °C during printing, and heat treatment at 60 °C for 20 min. The accumulation and overflow of AgNWs at the edges of the linear pattern were observed, which resulted in a decrease in printing accuracy. We successfully printed the heart-shaped pattern and then demonstrated that it could work well. This showed that the well-defined pattern with good photoelectric properties can be obtained by using an inkjet printing process with silver nanowires ink as inkjet material.
| S-EPMC8307527 | biostudies-literature
Project description:In this work we demonstrate a new approach towards the electroless deposition of tellurium nanowires in deep eutectic solvents. Unlike most electroless deposition where the substrate is sacrificed to drive the reduction, our process uses immobilised silver epoxy islands on gold films to give localised galvanic displacement of the silver, resulting in an even growth of wires across the entire gold electrode surface. We demonstrate the strong dependence of the nanostructure on the experimental conditions, with changes in bath temperature, tellurium concentration and the halide component of the solvent leading to sizeable alterations in the nanowire geometry. This demonstrates electroless deposition as a promising synthetic route towards low-dimensional tellurium nanostructures.
| S-EPMC9752427 | biostudies-literature
Project description:The potential applications of stretchable strain sensors in wearable electronics have garnered significant attention. However, developing susceptible stretchable strain sensors for practical applications still poses a considerable challenge. The present study introduces a stretchable strain sensor that utilizes silver nanowires (AgNWs) embedded into a polydimethylsiloxane (PDMS) substrate. The AgNWs have high flexibility and electrical conductivity. A stretchable AgNW/Pat-PDMS conductive film was prepared by arranging nanowires on the surface of PDMS using a simple rod coating method. Depending on the orientation angle, the overlap area between nanowires varies, resulting in different levels of separation under a given strain. Due to the separation of the nanowire and the change in current path geometry, the variation in strain resistance of the sensor can be primarily attributed to these factors. Therefore, precision in strain regulation can be adjusted by altering the angle θ (0°, 60°, or 90°) of the nanowire. At the same time, the stability of the AgNW/Pattern-PDMS (AgNW/Pat-PDMS) conductive film application was verified by preparing a sandwich structure PDMS/AgNW/Pat-PDMS stretchable strain sensor. The sensor exhibited high sensitivity within the operating sensing range (gauge factor (GF) of 15 within ~120% strain), superior durability (20,000 bending cycles and 5000 stretching cycles), and excellent response toward bending.
| S-EPMC11355971 | biostudies-literature
Project description:We report on investigating the structural and electronic properties of semiconducting and insulating layers produced in a process resembling percolation in a unique cold plasma fabrication method (plasma-enhanced chemical vapor deposition-PECVD). Amorphous carbon-tin films (Sn-C) produced from tetramethyl tin (TMT) with an acoustic-frequency glow discharge in a three-electrode reactor were investigated. The layers, after air exposure, oxidized to SnO2/Sn-C. Depending on the coupling capacitance applied to the plasma reactor, the films could be obtained in the form of an amorphous semiconductor or an amorphous insulator. We assume that the semiconductor consists of an internal network of channels auto-organized during deposition. The insulator does not demonstrate any internal structure features. An investigation on conductive filaments creating low-dimensional (LD) nanojunctions in the semiconductor and the location of energetic levels in the insulator was performed. The main parameters of the electronic band structure of the insulating film, such as the transport gap EG (5.2 eV), optical gap Eopt (3.1 eV), electron affinity Χ (2.1 eV), and ionization potential J (7.3 eV), were determined. We have demonstrated a simple approach for developing a catalyst candidate consisting of amorphous semiconductor-insulator nanojunctions for (photo)catalytic hydrogen evolution or CO2 reduction.
| S-EPMC10817613 | biostudies-literature