Electric Field-Driven Assembly of Sulfonated Polystyrene Microspheres.
Ontology highlight
ABSTRACT:
SUBMITTER: Mikkelsen A
PROVIDER: S-EPMC5507009 | biostudies-literature |
REPOSITORIES: biostudies-literature
Similar Datasets
Project description:Being able to systematically modify the electric properties of nano- and microparticles opens up new possibilities for the bottom-up fabrication of advanced materials such as the fabrication of one-dimensional (1D) colloidal and granular materials. Fabricating 1D structures from individual particles offers plenty of applications ranging from electronic sensors and photovoltaics to artificial flagella for hydrodynamic propulsion. In this work, we demonstrate the assembly of 1D structures composed of individual microparticles with modified electric properties, pulled out of a liquid environment into air. Polystyrene particles were modified by sulfonation for different reaction times and characterized by dielectric spectroscopy and dipolar force measurements. We found that by increasing the sulfonation time, the values of both electrical conductivity and dielectric constant of the particles increase, and that the relaxation frequency of particle electric polarization changes, causing the measured dielectric loss of the particles to shift towards higher frequencies. We attributed these results to water adsorbed at the surface of the particles. With sulfonated polystyrene particles exhibiting a range of electric properties, we showed how the electric properties of individual particles influence the formation of 1D structures. By tuning applied voltage and frequency, we were able to control the formation and dynamics of 1D structures, including chain bending and oscillation.
| S-EPMC5667018 | biostudies-literature
Project description:Topological defects appear in symmetry breaking phase transitions and are ubiquitous throughout Nature. As an ideal testbed for their study, defect configurations in nematic liquid crystals (NLCs) could be exploited in a rich variety of technological applications. Here we report on robust theoretical and experimental investigations in which an external electric field is used to switch between pre-determined stable chargeless disclination patterns in a nematic cell, where the cell is sufficiently thick that the disclinations start and terminate at the same surface. The different defect configurations are stabilised by a master substrate that enforces a lattice of surface defects exhibiting zero total topological charge value. Theoretically, we model disclination configurations using a Landau-de Gennes phenomenological model. Experimentally, we enable diverse defect patterns by implementing an in-house-developed Atomic Force Measurement scribing method, where NLC configurations are monitored via polarised optical microscopy. We show numerically and experimentally that an "alphabet" of up to 18 unique line defect configurations can be stabilised in a 4x4 lattice of alternating s=±1 surface defects, which can be "rewired" multistably using appropriate field manipulation. Our proof-of-concept mechanism may lead to a variety of applications, such as multistable optical displays and rewirable nanowires. Our studies also are of interest from a fundamental perspective. We demonstrate that a chargeless line could simultaneously exhibit defect-antidefect properties. Consequently, a pair of such antiparallel disclinations exhibits an attractive interaction. For a sufficiently closely-spaced pair of substrate-pinned defects, this interaction could trigger rewiring, or annihilation if defects are depinned.
| S-EPMC8051152 | biostudies-literature
Project description:Understanding spatiotemporal organization in bacteria under an external AC electric field is not only very interesting from a perspective of studying assembly and disassembly in a model biofilm but also provides insight into the intricate role of anisotropic interaction with bacterial dynamics that can generate interesting complex structures. In the current study, using confocal microscopy, we demonstrate such complex assemblies of monodisperse tetrad clusters of Micrococcus luteus, an environmental bacterium synthesized under a controlled growth condition. These clusters under the AC field produce a range of interesting structures such as chains, double helix, and bundles, which are instantaneously reversible when the field is switched off. Our studies can provide important insights into the natural organization of the clustered bacterium (with relevance in biofilm-like states) and generate strategies for biomaterial fabrication with a switchable functionality.
| S-EPMC7098059 | biostudies-literature
Project description:Electroporation is the formation of permeabilizing structures in the cell membrane under the influence of an externally imposed electric field. The resulting increased permeability of the membrane enables a wide range of biological applications, including the delivery of normally excluded substances into cells. While electroporation is used extensively in biology, biotechnology, and medicine, its molecular mechanism is not well understood. This lack of knowledge limits the ability to control and fine-tune the process. In this article we propose a novel molecular mechanism for the electroporation of a lipid bilayer based on energetics analysis. Using molecular dynamics simulations we demonstrate that pore formation is driven by the reorganization of the interfacial water molecules. Our energetics analysis and comparisons of simulations with and without the lipid bilayer show that the process of poration is driven by field-induced reorganization of water dipoles at the water-lipid or water-vacuum interfaces into more energetically favorable configurations, with their molecular dipoles oriented in the external field. Although the contributing role of water in electroporation has been noted previously, here we propose that interfacial water molecules are the main players in the process, its initiators and drivers. The role of the lipid layer, to a first-order approximation, is then reduced to a relatively passive barrier. This new view of electroporation simplifies the study of the problem, and opens up new opportunities in both theoretical modeling of the process and experimental research to better control or to use it in new, innovative ways.
| S-EPMC3623848 | biostudies-literature
Project description:We report a method for rapid, electric field directed assembly of high-density protein-conjugated microbead arrays. Photolithography is used to fabricate an array of micron to sub-micron-scale wells in an epoxy-based photoresist on a silicon wafer coated with a thin gold film, which serves as the primary electrode. A thin gasket is used to form a microfluidic chamber between the wafer and a glass coverslip coated with indium-tin oxide, which serves as the counter electrode. Streptavidin-conjugated microbeads suspended in a low conductance buffer are introduced into the chamber and directed into the wells via electrophoresis by applying a series of low voltage electrical pulses across the electrodes. Hundreds of millions of microbeads can be permanently assembled on these arrays in as little as 30 seconds and the process can be monitored in real time using epifluorescence microscopy. The binding of the microbeads to the gold film is robust and occurs through electrochemically induced gold-protein interactions, which allows excess beads to be washed away or recycled. The well and bead sizes are chosen such that only one bead can be captured in each well. Filling efficiencies greater than 99.9% have been demonstrated across wafer-scale arrays with densities as high as 69 million beads per cm(2). Potential applications for this technology include the assembly of DNA arrays for high-throughput genome sequencing and antibody arrays for proteomic studies. Following array assembly, this device may also be used to enhance the concentration-dependent processes of various assays through the accelerated transport of molecules using electric fields.
| S-EPMC2880398 | biostudies-literature
Project description:A gallium-based liquid metal got high attention recently, due to the excellent material properties that are useful in various research areas. We report here on electric field-induced liquid metal droplet generation and falling direction manipulation. The well-analyzed electro-hydrodynamic method is a selectable way to control the liquid metal, as the liquid metal is conductive. The electric field-induced liquid metal manipulation can be affected by the flow rate (0.05~0.2 mL/min), voltage (0~7 kV), and distance (15 and 30 mm) between electrodes, which changes the volume of the electric field-induced generated liquid metal droplet and the number of the generated droplets. When the electric field intensity increases or the flow rate increases, the generated droplet volume decreases, and the number of droplets increases. With the highest voltage of 7 kV with 15 mm between electrodes at the 0.2 mL/min flow rate, the lowest volume and the largest number of the generated droplets for 10 s were ~10 nL and 541, respectively. Additionally, we controlled the direction of the generated droplet by changing the electric field. The direction of the liquid metal droplet was controlled with the maximum angle of ~12°. Moreover, we exhibited a short circuit demonstration by controlling the volume or falling direction of the generated liquid metal droplet with an applied electric field.
| S-EPMC8471384 | biostudies-literature
Project description:Active colloids are a synthetic analogue of biological microorganisms that consume external energy to swim through viscous fluids. Such motion requires breaking the symmetry of the fluid flow in the vicinity of a particle; however, it is challenging to understand how surface and shape anisotropies of the colloid lead to a particular trajectory. Here, we attempt to deconvolute the effects of particle shape and surface anisotropy on the propulsion of model ellipsoids in alternating current (AC) electric fields. We first introduce a simple process for depositing metal patches of various shapes on the surfaces of ellipsoidal particles. We show that the shape of the metal patch is governed by the assembled structure of the ellipsoids on the substrate used for physical vapor deposition. Under high-frequency AC electric field, ellipsoids dispersed in water show linear, circular, and helical trajectories which depend on the shapes of the surface patches. We demonstrate that features of the helical trajectories such as the pitch and diameter can be tuned by varying the degree of patch asymmetry along the two primary axes of the ellipsoids, namely longitudinal and transverse. Our study reveals the role of patch shape on the trajectory of ellipsoidal particles propelled by induced charge electrophoresis. We develop heuristics based on patch asymmetries that can be used to design patchy particles with specified nonlinear trajectories.
| S-EPMC8279480 | biostudies-literature
Project description:Chiral molecules with opposite handedness exhibit distinct physical, chemical, or biological properties. They pose challenges as well as opportunities in understanding the phase behavior of soft matter, designing enantioselective catalysts, and manufacturing single-handed pharmaceuticals. Microscopic particles, arranged in a chiral configuration, could also exhibit unusual optical, electric, or magnetic responses. Here we report a simple method to assemble achiral building blocks, i.e., the asymmetric colloidal dimers, into a family of chiral clusters. Under alternating current electric fields, two to four lying dimers associate closely with a central standing dimer and form both right- and left-handed clusters on a conducting substrate. The cluster configuration is primarily determined by the induced dipolar interactions between constituent dimers. Our theoretical model reveals that in-plane dipolar repulsion between petals in the cluster favors the achiral configuration, whereas out-of-plane attraction between the central dimer and surrounding petals favors a chiral arrangement. It is the competition between these two interactions that dictates the final configuration. The theoretical chirality phase diagram is found to be in excellent agreement with experimental observations. We further demonstrate that the broken symmetry in chiral clusters induces an unbalanced electrohydrodynamic flow surrounding them. As a result, they rotate in opposite directions according to their handedness. Both the assembly and propulsion mechanisms revealed here can be potentially applied to other types of asymmetric particles. Such kinds of chiral colloids will be useful for fabricating metamaterials, making model systems for both chiral molecules and active matter, or building propellers for microscale transport.
| S-EPMC4443365 | biostudies-literature
Project description:Gradient biomaterials are considered as preferable matrices for tissue engineering due to better simulation of native tissues. The introduction of gradient cues usually needs special equipment and complex process but is only effective to limited biomaterials. Incorporation of multiple gradients in the hydrogels remains challenges. Here, beta-sheet rich silk nanofibers (BSNF) were used as building blocks to introduce multiple gradients into different hydrogel systems through the joint action of crosslinking and electric field. The blocks migrated to the anode along the electric field and gradually stagnated due to the solution-hydrogel transition of the systems, finally achieving gradient distribution of the blocks in the formed hydrogels. The gradient distribution of the blocks could be tuned easily through changing different factors such as solution viscosity, which resulted in highly tunable gradient of mechanical cues. The blocks were also aligned under the electric field, endowing orientation gradient simultaneously. Different cargos could be loaded on the blocks and form gradient cues through the same crosslinking-electric field strategy. The building blocks could be introduced to various hydrogels such as Gelatin and NIPAM, indicating the universality. Complex niches with multiple gradient cues could be achieved through the strategy. Silk-based hydrogels with suitable mechanical gradients were fabricated to control the osteogenesis and chondrogenesis. Chondrogenic-osteogenic gradient transition was obtained, which stimulated the ectopic osteochondral tissue regeneration in vivo. The versatility and highly controllability of the strategy as well as multifunction of the building blocks reveal the applicability in complex tissue engineering and various interfacial tissues.
| S-EPMC7093350 | biostudies-literature
Project description:The interplay between shape anisotropy and directed long-range interactions enables the self-assembly of complex colloidal structures. As a recent highlight, ellipsoidal particles polarized in an external electric field were observed to associate into well-defined tubular structures. In this study, we systematically investigate such directed self-assembly using Monte Carlo simulations of a two-point-charge model of polarizable prolate ellipsoids. In spite of its simplicity and computational efficiency, we demonstrate that the model is capable of capturing the complex structures observed in experiments on ellipsoidal colloids at low volume fractions. We show that, at sufficiently high electric field strength, the anisotropy in shape and electrostatic interactions causes a transition from three-dimensional crystal structures observed at low aspect ratios to two-dimensional sheets and tubes at higher aspect ratios. Our work thus illustrates the rich self-assembly behavior accessible when exploiting the interplay between competing long- and short-range anisotropic interactions in colloidal systems.
| S-EPMC5719464 | biostudies-literature