Browse
Submit Data
Databases
API
Help

Dataset Information

25 Views

0 Connections

0 Citations

0 Reanalyses

0 Downloads

Omics score: 0

Study on the NO removal efficiency of the lignite pyrolysis coke catalyst by selective catalytic oxidation method.

ABSTRACT: Selective catalytic oxidation (SCO) method is commonly used in wet denitration technology; NO after the catalytic oxidation can be removed with SO2 together by wet method. Among the SCO denitration catalysts, pyrolysis coke is favored by the advantages of low cost and high catalytic activity. In this paper, SCO method combined with pyrolysis coke catalyst was used to remove NO from flue gas. The effects of different SCO operating conditions and different pyrolysis coke catalyst made under different process conditions were studied. Besides, the specific surface area of the catalyst and functional groups were analyzed with surface area analyzer and Beohm titration. The results are: (1) The optimum operating conditions of SCO is as follows: the reaction temperature is 150°C and the oxygen content is 6%. (2) The optimum pyrolysis coke catalyst preparation processes are as follows: the pyrolysis final temperature is 750°C, and the heating rate is 44°C / min. (3) The characterization analysis can be obtained: In the denitration reaction, the basic functional groups and the phenolic hydroxyl groups of the catalyst play a major role while the specific surface area not.

SUBMITTER: Zhang L

PROVIDER: S-EPMC5549953 | biostudies-literature |

REPOSITORIES: biostudies-literature

ACCESS DATA

Json Xml

Similar Datasets

Synergistic Effects of Catalyst Mixtures on Biomass Catalytic Pyrolysis.

Project description:This paper studied the synergistic effects of catalyst mixtures on biomass catalytic pyrolysis in comparison with the single catalyst in a microwave reactor and a TGA. In general, positive synergistic effects were identified based on increased mass loss rate, reduced activation energy, and improved bio-oil quality compared to the case with a single catalyst at higher catalyst loads. 10KP/10Bento (a mixture of 10% K3PO4 and 10% bentonite) increased the mass loss rate by 85 and 45% at heating rates of 100 and 25°C/min, respectively, compared to switchgrass without catalyst. The activation energy for 10KP/10Bento and 10KP/10Clino (a mixture of 10% K3PO4 and 10% clinoptilolite) was slightly lower or similar to other catalysts at 30 wt.% load. The reduction in the activation energy by the catalyst mixture was higher at 100°C/min than 25°C/min due to the improved catalytic activity at higher heating rates. Synergistic effects are also reflected in the improved properties of bio-oil, as acids, aldehydes, and anhydrosugars were significantly decreased, whereas phenol and aromatic compounds were substantially increased. 30KP (30% K3PO4) and 10KP/10Bento increased the content of alkylated phenols by 341 and 207%, respectively, in comparison with switchgrass without catalyst. Finally, the use of catalyst mixtures improved the catalytic performance markedly, which shows the potential to reduce the production cost of bio-oil and biochar from microwave catalytic pyrolysis.

| S-EPMC7767908 | biostudies-literature

Dynamic Adsorption of Sulfamethoxazole from Aqueous Solution by Lignite Activated Coke.

Project description:In this paper, lignite activated coke was used as adsorbent for dynamic column adsorption experiments to remove sulfamethoxazole from aqueous solution. The effects of column height, flow rate, initial concentration, pH and humic acids concentration on the dynamic adsorption penetration curve and mass transfer zone length were investigated. Results showed penetration time would be prolonged significantly by increasing column height, while inhibited by the increasement of initial concentration and flow rate. Thomas and Yoon-Nelson model and the Adams-Bohart model were used to elucidate the adsorption mechanism, high coefficients of R2 > 0.95 were obtained in Thomas model for most of the adsorption entries, which revealed that the adsorption rate could probably be dominated by mass transfer at the interface. The average change rates of mass transfer zone length to the changes of each parameters, such as initial concentration, the column height, the flow rate and pH, were 0.0003, 0.6474, 0.0076, 0.0073 and 0.0191 respectively, revealed that column height may play a vital role in dynamic column adsorption efficiency. These findings suggested that lignite activated coke can effectively remove sulfamethoxazole contaminants from wastewater in practice.

| S-EPMC7179028 | biostudies-literature

Catalytic selective ethane dehydrogenation at low-temperature with low coke formation.

Project description:Catalytic ethane dehydrogenation (EDH) was investigated to improve the efficient production of ethylene, an extremely important chemical feedstock. The perovskite oxide YCrO3 was found to be more suitable than earlier reported catalysts because it exhibits greater activity and C2H4 selectivity (94.3%) in the presence of steam at 973 K. This catalyst shows the highest activity than ever under kinetic conditions, and shows very high ethane conversion under integral reaction conditions. Comparison with EDH performance under conditions without steam revealed that steam plays an important role in stabilizing the high activity. Raman spectra of spent catalysts indicated that steam prevents coke formation, which is responsible for deactivating YCrO3. Transmission IR and XPS measurements also revealed a mechanism by which H2O forms surface oxygen species on YCrO3, consequently removing C2H6-derived coke precursors rapidly and inhibiting coke accumulation.

| S-EPMC9425839 | biostudies-literature

Catalytic depolymerization of a typical lignite for improving tar yield by Co and Zn catalyst.

Project description:A novel process for improving tar yield through catalytic depolymerization of a typical lignite was put forward. The catalytic depolymerization of the lignite over CoCl2 and ZnCl2 catalyst in different concentrations were investigated by a Gray-King apparatus. The optimal catalyst concentrations of CoCl2 and ZnCl2 catalyst that could obtain the highest tar yield was achieved, by which the tar yield increased about 20.3% and 6.6% compared with that of the raw coal, respectively. Different with the traditional catalytic pyrolysis process for which the tar yield decreased, more tar was produced by the catalytic depolymerization method. The GC × GC-MS analysis showed that the components of alkanes and two-ring aromatics in tar increased dramatically with the addition of the optimal CoCl2 and ZnCl2 catalyst. The Raman measurement revealed that more large aromatic ring systems ( > 6 rings) were formed in the char from depolymerization with catalyst and the elemental analysis showed that the hydrogen content decreased slightly. The gas products analysis reflected the contents of methane showed an obvious decrease. All of this reflects that more fragments and small free radicals cracked were enhanced by catalysis in the catalytic depolymerization process, thereby leading to an enhancement of the tar formation possibilities.

| S-EPMC5663918 | biostudies-literature

Effect of catalytic pyrolysis conditions using pulse current heating method on pyrolysis products of wood biomass.

Project description:The influence of catalysts on the compositions of char and pyrolysis oil obtained by pyrolysis of wood biomass with pulse current heating was studied. The effects of catalysts on product compositions were analyzed using GC-MS and TEM. The compositions of some aromatic compounds changed noticeably when using a metal oxide species as the catalyst. The coexistence or dissolution of amorphous carbon and iron oxide was observed in char pyrolyzed at 800 °C with Fe3O4. Pyrolysis oil compositions changed remarkably when formed in the presence of a catalyst compared to that obtained from the uncatalyzed pyrolysis of wood meal. We observed a tendency toward an increase in the ratio of polyaromatic hydrocarbons in the pyrolysis oil composition after catalytic pyrolysis at 800 °C. Pyrolysis of biomass using pulse current heating and an adequate amount of catalyst is expected to yield a higher content of specific polyaromatic compounds.

| S-EPMC4294310 | biostudies-other

Catalytic Pyrolysis of Lignocellulosic Biomass: The Influence of the Catalyst Regeneration Sequence on the Composition of Upgraded Pyrolysis Oils over a H-ZSM-5/Al-MCM-41 Catalyst Mixture.

Project description:Catalyst regeneration is economically attractive, and it saves resources. Thus, it is important to determine the influence of catalyst regeneration on the chemical composition of upgraded oil. The catalyst was regenerated several times, and the regenerated catalyst was reloaded in the reactor to proceed with the next run. The composition of the derived upgraded pyrolysis oils in relation to catalyst regeneration was determined. The results revealed that the catalyst cracking abilities decreased with an increased number of reaction cycles. The opposite trends of the organic fraction and water yields indicated that the deoxygenation process occurred via H2O production. A decrease in the CO and CO2 yields revealed that the deoxygenation in catalytic pyrolysis with a catalyst mixture occurred via decarbonylation, decarboxylation, and dehydration mechanisms. The chemical formula of bio-oil changed from CH0.17O0.91 for a noncatalytic experiment to CH0.14O0.66 for a catalytic pyrolysis experiment after five reaction cycles, which indicated that the oxygen in the bio-oil decreased at the expense of hydrogen. The high heating value (HHV) of bio-oils decreased as the number of reaction cycles increased, albeit the minimum value of 22.41 wt % in the 6th reaction cycle was still higher than the value for the noncatalytic experiment. Compared to the HHVs of diesel fuel and gasoline petrol, the values of the produced bio-oil with catalyst mixtures were still low. The catalyst regained 94% of the surface area for the fresh catalyst, which indicated that the regeneration procedure was effective.

| S-EPMC7675534 | biostudies-literature

As(iii) removal through catalytic oxidation and Fe(iii) precipitation.

Project description:To remove arsenite (As(iii)) from wastewater effectively, the catalytic oxidation of As(iii) to arsenate (As(v)) and As(v) precipitation with iron ions (Fe(iii)) was investigated. The Pt/SiO2 catalyst functioned as a reaction site for As(iii) with oxygen in the atmosphere. The combination of the Pt/SiO2 catalyst and Fe(iii) precipitant improved the removal of As(iii) in the precipitate; Pt/SiO2 worked as both an As(iii) oxidation site and precipitation site with Fe(iii) precipitant.

| S-EPMC9171746 | biostudies-literature

A Highly Selective Vanadium Catalyst for Benzylic C-H Oxidation.

Project description:Vanadium complexes have been used extensively to catalyze olefin and alcohol oxidation. However, their application in C-H oxidation has not been well-studied. We report herein that commercially available Cp(2)VCl(2) catalyzes benzylic C-H oxidation selectively and effectively, giving no aromatic oxidation products.

| S-EPMC3375726 | biostudies-literature

Preparation of MnOx Supported LiOH Activated Soybean Oil Sludge Catalyst and Its Analysis in Denitration Mechanism of Selective Catalytic Oxidation (SCO).

Project description:Treatment with selective catalytic oxidation (SCO) is an effective technology applied recently for conversion of nitrogen oxides pollution control. In order to solve the problems of high cost and difficulties in practical application of SCO catalyst, it was put forward using the solid waste sludge from soybean oil plant as catalyst carrier to prepare denitration catalyst. The sludge was treated by alkaline activation and then MnOx-based sludge was prepared by impregnation. Finally, MnOx-based sludge was calcined in the muffle furnace. The effects of activation and calcination conditions on catalyst activity were investigated. Fourier transform infrared (FTIR), X-ray photoelectron spectroscopy (XPS), X-ray diffraction (XRD) and scanning electron microscopy (SEM) were used to characterize the activity of the sludge based denitration catalyst, and the structure and activity of the sludge based denitration catalyst were furtherly confirmed. According to the achieved results, (1) after activated by LiOH with a mass concentration of 15% for 4 hours, the surface of the sludge catalyst has more alkali functional groups, making the denitration of sludge catalyst the best; (2) the MnOx-based catalyst calcined in the muffle furnace with calcination temperature of 450 °C for 4 hours has obvious denitration efficiency.

| S-EPMC6690868 | biostudies-literature

UiO-66-supported Fe catalyst: a vapour deposition preparation method and its superior catalytic performance for removal of organic pollutants in water.

Project description:A vapour deposition (VD) method was established for preparation of the UiO-66-supported Fe (Fe/UiO-66) catalyst, which provided the first case of the metal-organic framework (MOF)-supported Fe catalyst prepared by using the vapour-based method. The Fe loading was around 7.0-8.5 wt% under the present preparation conditions. The crystal structure of UiO-66 was not obviously influenced by the Fe loading, while the surface area significantly decreased, implicating most of the Fe components resided in the pores on UiO-66. The results for the methyl orange (MO) removal tests showed that MO in aqueous solution can be removed by UiO-66 by adsorption, and in contrast, it can be oxidized by H2O2 with the catalysis of Fe/UiO-66. Further catalytic tests showed that Fe/UiO-66 was rather effective to catalyse the oxidation of benzene derivatives like aniline in water in terms of chemical oxygen demand (COD) removal efficiency. The catalytic test results for Fe/UiO-66 were compared to those of Fe/Al2O3 with the same Fe loading and to the catalysts reported in the literature. This paper provides a general strategy for VD preparation of MOF-supported Fe catalyst on the one hand, and new catalysts for removing organic pollutants from water, on the other hand.

| S-EPMC6502381 | biostudies-literature

OmicsDI is part of the ELIXIR infrastructure

OmicsDI is an Elixir interoperability service. Learn more ›

Tweets

OmicsDI Databases

PRIDE
PeptideAtlas
MassIVE
JPOST Repository
Physiome Model Repository

EGA
EVA
ENA
LINCS
PAXDB
Cell Collective

MetaboLights
Metabolomics Workbench
MetabolomeExpress
GNPS
BioModels
FAIRDOMHub

ArrayExpress
dbGaP
ExpressionAtlas
GEO
NODE

Information

Databases
Help
API
Contact us
Code on GitHub
Terms of use
Submit Data