Dataset Information

Different cadences and resistances in sub-maximal synchronous handcycling in able-bodied men: Effects on efficiency and force application.

ABSTRACT: With the introduction of an add-on handcycle, a crank system that can be placed in front of a wheelchair, handcycling was made widely available for daily life. With it, people go into town more easily, e.g. to do groceries; meet up with friends, etc. They have more independency and can be socially active. Our aim is to explore some settings of the handcycle, so that it can be optimally used as a transportation device. Therefore, the effects of cadence and added resistance on gross mechanical efficiency and force application during sub-maximal synchronous handcycling were investigated. We hypothesized that a cadence of 52 rpm with a higher resistance (35 W) would lead to a higher gross mechanical efficiency and a more tangential force application than a higher cadence of 70 rpm and no extra resistance (15 W).Twelve able-bodied men rode in an instrumented add-on handcycle on a motorized level treadmill at 1.94 m/s. They performed three sessions of three four-minute blocks of steady state exercise. Gear (70, 60 and 52 rpm) was changed in-between the blocks and resistance (rolling resistance +0 W, +10 W, +20 W) was changed across sessions, both in a counterbalanced order. 3D force production, oxygen uptake and heart rate were measured continuously. Gross mechanical efficiency (ME) and fraction of effective force (FEF) were calculated as main outcomes. The effects of cadence and resistance were analyzed using a repeated measures ANOVA (P<0.05) with Bonferroni-corrected post-hoc pairwise comparisons.With a decrease in cadence a slight increase in ME (70 rpm: 5.5 (0.2)%, 60 rpm: 5.7 (0.2)%, 52 rpm: 5.8 (0.2)%, P = 0.008, ?2p = 0.38), while an increase in FEF (70 rpm: 58.0 (3.2)%, 60 rpm: 66.0 (2.8)%, 52 rpm: 71.3 (2.3)%, P<0.001, ?2p = 0.79) is seen simultaneously. Also with an increase in resistance an increase in ME (+0 W: 4.0 (0.2)%, +10 W: 6.0 (0.3)%, +20 W: 7.0 (0.2)%, P<0.001, ?2p = 0.92) and FEF (+0 W: 59.0 (2.9)%, +10 W: 66.1 (3.4)%, +20 W: 70.2 (2.4)%, P<0.001, ?2p = 0.56) was found.A cadence of 52 rpm against a higher resistance of about 35 W leads to a more optimal direction of forces and is more mechanically efficient than propelling at a higher cadence or lower resistance. Therefore, changing gears on a handcycle is important, and it is advised to keep the linear hand velocity relatively low for locomotion purposes.

SUBMITTER: Kraaijenbrink C

PROVIDER: S-EPMC5571929 | biostudies-literature | 2017

REPOSITORIES: biostudies-literature

ACCESS DATA

Publications

Different cadences and resistances in sub-maximal synchronous handcycling in able-bodied men: Effects on efficiency and force application.

Kraaijenbrink Cassandra C Vegter Riemer J K RJK Hensen Alexander H R AHR Wagner Heiko H van der Woude Lucas H V LHV

PloS one 20170825 8

<h4>Background</h4>With the introduction of an add-on handcycle, a crank system that can be placed in front of a wheelchair, handcycling was made widely available for daily life. With it, people go into town more easily, e.g. to do groceries; meet up with friends, etc. They have more independency and can be socially active. Our aim is to explore some settings of the handcycle, so that it can be optimally used as a transportation device. Therefore, the effects of cadence and added resistance on g ...[more]

PMID: 28841704

Similar Datasets

Project description:BACKGROUND:Originally, the cranks of a handcycle were mounted with a 180° phase shift (asynchronous). However, as handcycling became more popular, the crank mode switched to a parallel mounting (synchronous) over the years. Differences between both modes have been investigated, however, not into great detail for propulsion technique or practice effects. Our aim is to compare both crank modes from a biomechanical and physiological perspective, hence considering force and power production as a cause of physiological outcome measures. This is done within a practice protocol, as it is expected that motor learning takes place in the early stages of handcycling in novices. METHODS:Twelve able-bodied male novices volunteered to take part. The experiment consisted of a pre-test, three practice sessions and a post-test, which was subsequently repeated for both crank modes in a counterbalanced manner. In each session the participants handcycled for 3?×?4 minutes on a leveled motorized treadmill at 1.94?m/s. Inbetween sessions were 2 days of rest. 3D forces, handlebar and crank angle were measured on the left hand side. Kinematic markers were placed on the handcycle to monitor the movement on the treadmill. Lastly, breath-by-breath spirometry combined with heart-rate were continuously measured. The effects of crank mode and practice-based learning were analyzed using a two way repeated measures ANOVA, with synchronous vs asynchronous and pre-test vs post-test as within-subject factors. RESULTS:In the pre-test, asynchronous handcycling was less efficient than synchronous handcycling in terms of physiological strain, force production and timing. At the post-test, the metabolic costs were comparable for both modes. The force production was, also after practice, more efficient in the synchronous mode. External power production, crank rotation velocity and the distance travelled back and forwards on the treadmill suggest that asynchronous handcycling is more constant throughout the cycle. CONCLUSIONS:As the metabolic costs were reduced in the asynchronous mode, we would advise to include a practice period, when comparing both modes in scientific experiments. For handcycle users, we would currently advise a synchronous set-up for daily use, as the force production is more effective in the synchronous mode, even after practice.

Project description:Real-life daily handcycling requires combined propulsion and steering to control the front wheel. Today, the handcycle cranks are mostly mounted synchronously unlike the early handcycle generations. Alternatively, arm cycle ergometers do not require steering and the cranks are mostly positioned asynchronously. The current study aims to evaluate the effects of combining propulsion and steering requirements on synchronous and asynchronous submaximal handcycle ergometry. We hypothesize that asynchronous handcycling with steering results in the mechanically least efficient condition, due to compensation for unwanted rotations that are not seen in synchronous handcycling, regardless of steering. Sixteen able-bodied male novices volunteered in this lab-based experiment. The set-up consisted of a handcycle ergometer with 3D force sensors at each crank that also allows "natural" steering. Four submaximal steady-state (60 rpm, ~35 W) exercise conditions were presented in a counterbalanced order: synchronous with a fixed steering axis, synchronous with steering, asynchronous with a fixed axis and asynchronous with steering. All participants practiced 3 × 4 mins with 30 mins rest in between every condition. Finally, they did handcycle for 4 mins in each of the four conditions, interspaced with 10 mins rest, while metabolic outcomes, kinetics and kinematics of the ergometer were recorded. The additional steering component did not influence velocity, torque and power production during synchronous handcycling and therefore resulted in an equal metabolically efficient handcycling configuration compared to the fixed condition. Contrarily, asynchronous handcycling with steering requirements showed a reduced mechanical efficiency, as velocity around the steering axis increased and torque and power production were less effective. Based on the torque production around the crank and steering axes, neuromuscular compensation strategies seem necessary to prevent steering movements in the asynchronous mode. To practice or test real-life daily synchronous handcycling, a synchronous crank set-up of the ergometer is advised, as exercise performance in terms of mechanical efficiency, metabolic strain, and torque production is independent of steering requirements in that mode. Asynchronous handcycling or arm ergometry demands a different handcycle technique in terms of torque production and results in higher metabolic responses than synchronous handcycling, making it unsuitable for testing.

Project description:Introduction: The primary aims of the present study were to assess the relationships of early (0–50 ms) and late (100–200 ms) knee extensor rate of force development (RFD) with maximal voluntary force (MVF) and sit-to-stand (STS) performance in participants with chronic kidney disease (CKD) not requiring dialysis. Methods: Thirteen men with CKD (eGFR = 35.17 ±.5 ml/min per 1.73 m2, age = 70.56 ±.4 years) and 12 non-CKD men (REF) (eGFR = 80.31 ± 4.8 ml/min per 1.73 m2, age = 70.22 ±.9 years) performed maximal voluntary isometric contractions to determine MVF and RFD of the knee extensors. RFD was measured at time intervals 0–50 ms (RFD0–50) and 100–200 ms (RFD100–200). STS was measured as the time to complete five repetitions. Measures of rectus femoris grayscale (RF GSL) and muscle thickness (RF MT) were obtained via ultrasonography in the CKD group only. Standardized mean differences (SMD) were used to examine differences between groups. Bivariate relationships were assessed by Pearson’s product moment correlation. Results: Knee extensor MVF adjusted for body weight (CKD=17.14 ±.1 N·kg0.67, REF=21.55 ±.3 N·kg0.67, SMD = 0.79) and STS time (CKD = 15.93 ±.4 s, REF = 12.23 ±.7 s, SMD = 1.03) were lower in the CKD group than the REF group. Absolute RFD100–200 was significantly directly related to adjusted MVF in CKD (r = 0.56, p = 0.049) and REF (r = 0.70, p = 0.012), respectively. STS time was significantly inversely related to absolute (r = −0.75, p = 0.008) and relative RFD0–50 (r = −0.65, p = 0.030) in CKD but not REF (r = 0.08, p = 0.797; r = 0.004, p = 0.991). Significant inverse relationships between RF GSL adjusted for adipose tissue thickness and absolute RFD100–200 (r =−0.59, p = 0.042) in CKD were observed. Conclusion: The results of the current study highlight the declines in strength and physical function that occur in older men with CKD stages 3b and 4 not requiring dialysis. Moreover, early RFD was associated with STS time in CKD while late RFD was associated MVF in both CKD and REF. Clinical Trial Registration: ClinicalTrials.gov, identifier: NCT03160326 and NCT02277236.

Project description:Constraint-based modeling techniques have become a standard tool for the in silico analysis of metabolic networks. To further improve their accuracy, recent methodological developments focused on integration of thermodynamic information in metabolic models to assess the feasibility of flux distributions by thermodynamic driving forces. Here we present OptMDFpathway, a method that extends the recently proposed framework of Max-min Driving Force (MDF) for thermodynamic pathway analysis. Given a metabolic network model, OptMDFpathway identifies both the optimal MDF for a desired phenotypic behavior as well as the respective pathway itself that supports the optimal driving force. OptMDFpathway is formulated as a mixed-integer linear program and is applicable to genome-scale metabolic networks. As an important theoretical result, we also show that there exists always at least one elementary mode in the network that reaches the maximal MDF. We employed our new approach to systematically identify all substrate-product combinations in Escherichia coli where product synthesis allows for concomitant net CO2 assimilation via thermodynamically feasible pathways. Although biomass synthesis cannot be coupled to net CO2 fixation in E. coli we found that as many as 145 of the 949 cytosolic carbon metabolites contained in the genome-scale model iJO1366 enable net CO2 incorporation along thermodynamically feasible pathways with glycerol as substrate and 34 with glucose. The most promising products in terms of carbon assimilation yield and thermodynamic driving forces are orotate, aspartate and the C4-metabolites of the tricarboxylic acid cycle. We also identified thermodynamic bottlenecks frequently limiting the maximal driving force of the CO2-fixing pathways. Our results indicate that heterotrophic organisms like E. coli hold a possibly underestimated potential for CO2 assimilation which may complement existing biotechnological approaches for capturing CO2. Furthermore, we envision that the developed OptMDFpathway approach can be used for many other applications within the framework of constrained-based modeling and for rational design of metabolic networks.

Dataset Information

Different cadences and resistances in sub-maximal synchronous handcycling in able-bodied men: Effects on efficiency and force application.

Publications

Different cadences and resistances in sub-maximal synchronous handcycling in able-bodied men: Effects on efficiency and force application.

Similar Datasets

OmicsDI is part of the ELIXIR infrastructure

Tweets