Data on physicochemical properties of active films derived from plantain flour/PCL blends developed under reactive extrusion conditions.
Ontology highlight
ABSTRACT:
SUBMITTER: Gutierrez TJ
PROVIDER: S-EPMC5645474 | biostudies-literature | 2017 Dec
REPOSITORIES: biostudies-literature
Publications
Data on physicochemical properties of active films derived from plantain flour/PCL blends developed under reactive extrusion conditions.
Gutiérrez Tomy J TJ Alvarez Vera A VA
Data in brief 20170930
The data given below relates to the research paper entitled: "Eco-friendly films prepared from plantain flour/PCL blends under reactive extrusion conditions using zirconium octanoate as a catalyst", recently published by our research group [1]. This article provides information concerning the physicochemical properties of the above-mentioned film systems: thickness, density, opacity, moisture content and surface moisture. ...[more]
Similar Datasets
Project description:The objective was to modify functional properties of breadfruit flours using twin-screw extrusion and test the physicochemical properties of the extruded flours. Extruded breadfruit flours were produced with twin-screw extrusion using different last barrel temperature (80 °C or 120 °C) and feed moisture content (17% or 30%). These conditions resulted in four extruded flours with different mechanical (specific mechanical energy, SME) and thermal (melt temperature) energies. At temperatures below the gelatinization of the native starch (<70 °C), swelling power was increased in all extruded treatments. Solubility was dramatically increased in high-SME extruded flours at all tested temperatures. Water holding capacity was dramatically increased in the low-SME extruded flours. A two-fold higher cold peak viscosity was obtained for low SME-high temperature extruded flour compared with the other extruded flours. Low SME-low temperature extruded flour still exhibited a hot peak viscosity, which occurred earlier than in native flour. Setback was decreased in all extruded flours, especially in high-SME treatments. The incorporation of extruded flours into soy protein gels did not affect cooking loss, while hardness and springiness decreased with the addition of extruded flours. Overall, extrusion of breadfruit flour altered functional flour properties, including water holding capacity and pasting properties, and modified the texture of soy protein gels.
| S-EPMC7465982 | biostudies-literature
Project description:Poly(hydroxybutyrate) (PHB) is a biopolymer biologically synthesized by controlled bacterial fermentation from a wide variety of microorganisms. PHB is proposed as a potential green alternative to commonly used plastics in packaging, due to its biodegradability and biocompatibility. However, if PHB is to replace commodities, it has some limitations regarding its thermo-mechanical performance to overcome. Among them are its critically the low toughness values at room temperature and poor thermoforming ability. With the aim of overcoming these weaknesses, in this work, blends of PHB with the addition of a biodegradable thermoplastic elastomer (bio-TPE) were prepared and evaluated. Films of such compounds were made by cast extrusion. In order to enhance the compatibility of both polymers during the extrusion process, three different reactive agents (poly-hexametylene diisocianate, triglycidyl isocyanurate, and Joncryl® ADR-4368) were assessed. The morphology and mechanical- and thermal properties of the films obtained were analyzed. In addition, the thermoforming ability of the produced films was evaluated. The results show that the plasticizers present in the bio-TPE interacted with the reactive agents, making them chemical competitors and altering the outcome of the blends.
| S-EPMC8840646 | biostudies-literature
Project description:The popularity of adding pulse flours to baked goods is growing rapidly due to their recognised health benefits. In this study, increasing amounts (3, 7, 10, and 15%) of white lupin flour (Lupinus albus L.) and of protein concentrate from narrow-leaved lupin (Lupinus angustifolius L.) were used as replacements for durum wheat semolina to prepare bread, and their effects on the physicochemical properties of the flour blends, as well as the technological and sensory qualities of bread, were evaluated. The addition of protein concentrate from narrow-leaved lupin and white lupin flour increased the water binding capacity and the leavening rate compared to pure semolina. A farinograph test indicated that the dough development time had a slight but significant tendency to increase with the addition of lupin flour and protein concentrate of narrow-leaved lupin, while had a negative effect on the stability of dough. The alveograph strength decreased (225, 108, and 76 × 10-4 J for dough made with semolina, 15% of protein concentrate from narrow-leaved lupin, and 15% of white lupin flour, respectively), whereas there was an upward trend in the P/L ratio. Compared to re-milled semolina, the samples with lupin flour and protein concentrate from narrow-leaved lupin had low amylase activity, with falling number values ranging from 439 s to 566 s. The addition of the two different lupin flours lowered the specific volumes of the breads (2.85, 2.39, and 1.93 cm3/g for bread made from semolina, from 15% of protein concentrate from narrow-leaved lupin, and from 15% of white lupin flour, respectively) and increased their hardness values (up to 21.34 N in the bread with 15% of protein concentrate from narrow-leaved lupin). The porosity of the loaves was diminished with the addition of the two lupin flours (range of 5-8). The sensory analysis showed that the addition of white lupin flour or protein concentrate from narrow-leaved lupin did not impart any unpleasant flavours or odours to the bread. To conclude, the use of lupin in breadmaking requires adjustments to strengthen the gluten network but does not require a deflavouring process.
| S-EPMC10931101 | biostudies-literature
Project description:Structuring blends on sub-micrometer scales, especially nano-scales, has a higher potential for improving their thermomechanical properties. Here, we propose a design strategy to fabricate compatible nano-blends by manipulating the reactions between two biodegradable polymers, e.g. polybutylene succinate (PBS) and polybutylene adipate terephthalate (PBAT), with extremely low free radical contents through reactive extrusion processing. Observed by transmission electron microscopy (TEM) and atomic force microscopy (AFM), it is found that PBAT is tightly surrounded by large amounts of PBS-PBAT co-polymers and dispersed in a PBS matrix with a particle size of less than 100 nm. We show how impact strength and polymer moduli can be improved simultaneously by decreasing the small amount of dispersed phase into nano-scale (droplet or lamina structures). With 5 wt% PBAT content in the PBS-PBAT blend, the notched impact strength of PBS is increased 1200% and the Young's modulus is increased 15%. Through in situ rheological monitoring and Fourier-transform infrared spectroscopy (FTIR) studies, the reason why nano-blends can be formed in such a low amount of peroxide is illustrated. Our investigation most significantly indicates the transformation of the partially compatible PBS-PBAT micro-blend into a fully compatible PBS-PBAT through nano-structuring. This work addresses the importance of reaction rate and mechanism in favoring the formation of co-polymers rather than homo-polymer crosslinking or self-decomposition in polymer blend modification via reactive extrusion design.
| S-EPMC9060287 | biostudies-literature
Project description:ABS/PA6-compatibilized blends were prepared by in situ reactive extrusion method. The main objective was to evaluate the influences of the morphology and blend composition on the rheological and nonisothermal crystallization properties. The morphology of submicron-sized ABS droplets evenly dispersed in PA6 led to dilatant fluid behavior and a transition from elastic to viscous behavior in the low-frequency region. The crystallization results indicated that reactive blends had elevated crystallization temperatures and crystallization rates, which were due to the heterogeneous nucleation of the submicron-sized ABS particles. In addition, it was observed that the theory by Mo suitably described the nonisothermal crystallization process. The activation energy slightly decreased for ABS contents of 5 and 15 wt % and then increased for a content of 25 wt %, indicating that the ABS promoted the crystallization of the blends at appropriate contents.
| S-EPMC7331037 | biostudies-literature
Project description:Blends of poly (L-lactide) (PLLA) and poly (?-caprolactone) (PCL) with and without paclitaxel were prepared via solution casting. DSC analysis as well as SEM analysis of the PLLA/PCL blend solution cast films showed that these blends are all phase separated.%PLLA crystallinity was found to increase with increasing PCL content (up till 15 wt.%). The PCL phase is found to homogeneously disperse in the PLLA matrix as spherical domains where the pore diameters of the PCL domains significantly increased with increasing PCL content. The degradation profiles matched with the slower degrading component PCL rather than PLLA and also increasing PCL content of the blends increased the degradation rate relatively. The increased crystallinity of the PLLA phase with increasing PCL contents confirmed that the degradation occurred through PCL phase. Cell proliferation on PLLA/PCL blends showed that all these blends were suitable for the support of cellular growth. Apoptosis assay with the paclitaxel-loaded PLLA/PCL blends showed an increase in cell death throughout 7 days of incubation where the cell death was increased with increasing PCL contents. This was attributed to the faster release of paclitaxel which was at least partially affected by the faster degradation rate at increasing PCL contents. The paclitaxel release was shown to be degradation controlled in the initial stages followed by a faster diffusion-controlled release in the later stages. These polymer blends were found to be very suitable paclitaxel release agents for which the paclitaxel release times can be altered with the composition of the blend and the film thickness.
| S-EPMC3225542 | biostudies-literature
Project description:Ternary-blended, melt-blown films of polylactide (PLA), polycaprolactone (PCL) and cellulose acetate butyrate (CAB) were prepared from preliminary miscibility data using a rapid screening method and optical ternary phase diagram (presented as clear, translucent, and opaque regions) as a guide for the composition selection. The compositions that provided optically clear regions were selected for melt blending. The ternary (PLA/PCL/CAB) blends were first melt-extruded and then melt-blown to form films and characterized for their tensile properties, tensile fractured-surface morphology, miscibility, crystallinity, molecular weight and chemical structure. The results showed that the tensile elongation at the break (%elongation) of the ternary-blended, melt-blown films (85/5/10, 75/10/15, 60/15/25 of PLA/PCL/CAB) was substantially higher (>350%) than pure PLA (ca. 20%). The range of compositions in which a significant increase in %elongation was observed at 55-85% w/w PLA, 5-20% w/w PCL and 10-25% w/w CAB. Films with high %elongation all showed good interfacial interactions between the dispersed phase (PCL and CAB) and matrix (PLA) in FE-SEM and showed improvements in miscibility (higher intermolecular interaction and mixing) and a decrease in the glass transition temperature, when compared to the low %elongation films. The decrease in Mw and Mn and the formation of the new NMR peaks (1H NMR at 3.68-3.73 ppm and 13C NMR at 58.54 ppm) were observed in only the high %elongation films. These are expected to be in situ compatibilizers that are generated during the melt processing, mostly by chain scission. In addition, mathematical modelling was used to study the optimal ratio and cost-effectiveness of blends with optimised mechanical properties. These ternary-blended, melt-blown films have the potential for use in both packaging and medical devices with excellent mechanical performance as well as inherent economic and environmental capabilities.
| S-EPMC9864367 | biostudies-literature
Project description:In this work poly(ε-caprolactone) (PCL) based electrospun mats were prepared by blending PCL with microcrystalline cellulose (MCC) and poly(3-hydroxybutyrate) (PHB). The electrospinning processing parameters were firstly optimized with the aim to obtain scalable PCL-based electrospun mats to be used in the industrial sector. Neat PCL as well as PCL-MCC and PCL-PHB based mats in different proportions (99:1; 95:5; 90:10) were prepared. A complete morphological, thermal and mechanical characterization of the developed materials was carried out. Scanning electron microscopy (SEM) observations showed that the addition of PHB to the PCL matrix considerably reduced the formation of beads. Both the addition of MCC and PHB reduced the thermal stability of PCL, but obtained materials with enough thermal stability for the intended use. The electrospun PCL fibers show greatly reduced flexibility with respect to the PCL bulk material, however when PCL is blended with PHB their stretchability is increased, changing their elongation at break from 35% to 70% when 10 wt% of PHB is blended with PCL. However, the mechanical response of the different blends increases with respect to the neat electrospun PCL, offering the possibility to modulate their properties according to the required industrial applications.
| S-EPMC7504022 | biostudies-literature
Project description:The formulation of new food products with high nutritional quality and functionality is gaining global attention. The physicochemical properties, in vitro digestibility, antioxidant activity and consumer acceptability of biscuits produced from germinated finger millet (GFM) (Eleusine coracana) and Bambara groundnut (GBGN) (Vigna subterranea) flour blends were investigated. As the proportion of GBGN flour increased in the biscuit samples, protein, in vitro protein digestibility (80.52-89.20 %), slowly digestible and resistant starch, total phenolic content and antioxidant activities increased significantly, while rapidly digestible starch, starch hydrolysis index, glycemic index and phytic acid decreased. Addition of GBGN also positively influenced the physical attributes of the biscuits. The blending of 80% GFM with 20 % GBGN resulted in a biscuit with acceptable sensory qualities such as taste, aroma, appearance, crunchiness, and overall acceptability. This study showed that GFM and GBGN flour blends could serve as functional ingredients to produce better products.
| S-EPMC9562233 | biostudies-literature
Project description:: Epoxy/Polycaprolactone (PCL) blends cured with a conventional diamine (4,4'-diaminodiphenylmethane, DDM) and with different amounts of a disulfide containing diamine (4, 4´-dithioaniline, DSS) were prepared through melting. The curing process was studied by FTIR and differential scanning calorimetry (DSC) and the mechanical behavior of the networks was studied by DMA. The shape memory properties and the recyclability of the materials were also analyzed. All blends showed a very high curing degree and temperature activated shape memory effect, related to the glass transition of the epoxy resin. The PCL plasticized the mixture, allowing tailoring of the epoxy glass transition. In addition, in the blends cured with DSS, as a consequence of the disulfide exchange reaction, the permanent shape could be erased and a new shape could be reprogrammed. Using this strategy, reprogrammable permanent shape memory materials were obtained.
| S-EPMC7180467 | biostudies-literature