Finite element simulation and clinical follow-up of lumbar spine biomechanics with dynamic fixations.
Ontology highlight
ABSTRACT:
SUBMITTER: Mas Y
PROVIDER: S-EPMC5706716 | biostudies-literature |
REPOSITORIES: biostudies-literature
Similar Datasets
Project description:Literature and field data from CIREN database have shown that lumbar spine injuries occur during car crashes. There are multiple hypotheses regarding how they occur; however, there is no biomechanical explanation for these injuries during collisions with road safety barriers (RSBs). Therefore, the objective of this study was to investigate the mechanics of vertebral fractures during car collisions with concrete RSBs. The finite element method was used for the numerical simulations. The global model of the car collision with the concrete RSB was created. The lumbar spine kinematics were extracted from the global simulation and then applied as boundary conditions to the detailed lumbar spine model. The results showed that during the collision, the occupant was elevated, and then dropped during the vehicle landing. This resulted in axial compression forces 2.6 kN with flexion bending moments 34.7 and 37.8 Nm in the L2 and L3 vertebrae. It was shown that the bending moment is the result of the longitudinal force on the eccentricity. The lumbar spine index for the L1-L5 section was 2.80, thus indicating a lumbar spine fracture. The minimum principal strain criterion of 7.4% and damage variable indicated L2 and L3 vertebrae and the inferior part of L1, as those potentially prone to fracture. This study found that lumbar spine fractures could occur as a consequence of vehicle landing during a collision with a concrete RSB mostly affecting the L1-L3 lumbar spine section. The fracture was caused by a combination of axial forces and flexion bending moments.
| S-EPMC8591065 | biostudies-literature
Project description:BackgroundAlthough it is critical to understand the accelerated degeneration of adjacent segments after fusion, the biomechanical properties of the spine have not been thoroughly studied after various fusion techniques. This study investigates whether four Roussouly's sagittal alignment morphotypes have different biomechanical characteristics after different single- or double-level spinal fixations.MethodsThe parametric finite element (FE) models of Roussouly's type (1-4) were developed based on the radiological data of 625 Chinese community population. The four Roussouly's type models were reassembled into four fusion models: single-level L4-5 Coflex fixation model, single-level L4-5 Fusion (pedicle screw fixation) model, double-level Coflex (L4-5) + Fusion (L5-S1) model, and double-level Fusion (L4-5) + Fusion (L4-5) model. A pure moment of 7.5 Nm was applied to simulate the physiological activities of flexion, extension, lateral bending and axial rotation.ResultsBoth single-level and double-level spinal fixation had the greatest effect on lumbar range of motion, disc pressure, and annulus fibrosis stress in flexion, followed by lateral bending, extension, and axial rotation. In all models, the upper adjacent segment was the most influenced by the implantation and bore the most compensation from the fixed segment. For Type 2 lumbar, the L4-L5 Coflex effectively reduced the disc pressure and annulus fibrosis stress in adjacent segments compared to the L4-L5 Fusion. Similarly, the L4-L5 Coflex offered considerable advantages in preserving the biomechanical properties of adjacent segments for Type 1 lumbar. For Type 4 lumbar, the L4-L5 Coflex did not have superiority over the L4-L5 Fusion, resulting in a greater increase in range of motion at adjacent segments in flexion and extension. The difference between the two fixations was not apparent in Type 3 lumbar. Compared to the single-level Fusion, the changes in motion and mechanics of the lumbar increased after both the double-level Coflex + Fusion and Fusion + Fusion fixations, while the differences between two double-level fixation methods on adjacent segments of the four lumbar models were similar to that of the single-level fixation.ConclusionType 3 and Type 4 lumbar have good compensatory ability and therefore allow for a wider range of surgical options, whereas surgical options for small lordotic Type 1 and Type 2 lumbar are more limited and severe.
| S-EPMC10712158 | biostudies-literature
Project description:The lack of a universal simulation method for triboelectric nanogenerator (TENG) makes the device design and optimization difficult before experiment, which protracts the research and development process and hinders the landing of practical TENG applications. The existing electrostatic induction models for TENGs have limitations in simulating TENGs with complex geometries and their dynamic behaviors under practical movements due to the topology change issues. Here, a dynamic finite element method (FEM) model is proposed. The introduction of air buffer layers and the moving mesh method eliminates the topology change issues during practical movement and allows simulation of dynamic and time-varying behaviors of TENGs with complex 2D/3D geometries. Systematic investigations are carried out to optimize the air buffer thickness and mesh densities, and the optimized results show excellent consistency with the experimental data and results based on other existing methods. It also shows that a 3D disk-type rotating TENG can be simulated using the model, clearly demonstrating the capability and superiority of the dynamic FEM model. Moreover, the dynamic FEM model is used to optimize the shape of the tribo-material, which is used as a preliminary example to demonstrate the possibility of designing a TENG-based sensor.
| S-EPMC7506595 | biostudies-literature
Project description:Simulation-based medicine and the development of complex computer models of biological structures is becoming ubiquitous for advancing biomedical engineering and clinical research. Finite element analysis (FEA) has been widely used in the last few decades to understand and predict biomechanical phenomena. Modeling and simulation approaches in biomechanics are highly interdisciplinary, involving novice and skilled developers in all areas of biomedical engineering and biology. While recent advances in model development and simulation platforms offer a wide range of tools to investigators, the decision making process during modeling and simulation has become more opaque. Hence, reliability of such models used for medical decision making and for driving multiscale analysis comes into question. Establishing guidelines for model development and dissemination is a daunting task, particularly with the complex and convoluted models used in FEA. Nonetheless, if better reporting can be established, researchers will have a better understanding of a model's value and the potential for reusability through sharing will be bolstered. Thus, the goal of this document is to identify resources and considerate reporting parameters for FEA studies in biomechanics. These entail various levels of reporting parameters for model identification, model structure, simulation structure, verification, validation, and availability. While we recognize that it may not be possible to provide and detail all of the reporting considerations presented, it is possible to establish a level of confidence with selective use of these parameters. More detailed reporting, however, can establish an explicit outline of the decision-making process in simulation-based analysis for enhanced reproducibility, reusability, and sharing.
| S-EPMC3278509 | biostudies-literature
Project description:PurposeThe purpose of this study was to investigate finite element biomechanical properties of the novel transpedicular transdiscal (TPTD) screw fixation with interbody arthrodesis technique in lumbar spine.MethodsAn L4-L5 finite element model was established and validated. Then, two fixation models, TPTD screw system and bilateral pedicle screw system (BPSS), were established on the validated L4-L5 finite element model. The inferior surface of the L5 vertebra was set immobilised, and moment of 7.5 Nm was applied on the L4 vertebra to test the range of motion (ROM) and stress at flexion, extension, lateral bending and axial rotation.ResultsThe intact model was validated for prediction accuracy by comparing two previously published studies. Both of TPTD and BPSS fixation models displayed decreased motion at L4-L5. The ROMs of six moments of flexion, extension, left lateral bending, right lateral bending, left axial rotation and right axial rotation in TPTD model were 1.92, 2.12, 1.10, 1.11, 0.90 and 0.87°, respectively; in BPSS model, they were 1.48, 0.42, 0.35, 0.38, 0.74 and 0.75°, respectively. The screws' peak stress of above six moments in TPTD model was 182.58, 272.75, 133.01, 137.36, 155.48 and 150.50 MPa, respectively; and in BPSS model, it was 103.16, 129.74, 120.28, 134.62, 180.84 and 169.76 MPa, respectively.ConclusionBoth BPSS and TPTD can provide stable biomechanical properties for lumbar spine. The decreased ROM of flexion, extension and lateral bending was slightly more in BPSS model than in TPTD model, but TPTD model had similar ROM of axial rotation with BPSS model. The screws' peak stress of TPTD screw focused on the L4-L5 intervertebral space region, and more caution should be put at this site for the fatigue breakage.The translational potential of this articleOur finite element study provides the biomechanical properties of novel TPTD screw fixation, and promotes this novel transpedicular transdiscal screw fixation with interbody arthrodesis technique be used clinically.
| S-EPMC6172361 | biostudies-literature
Project description:In the past 15 years, the finite element (FE) method has become a ubiquitous tool in the repertoire of evolutionary biologists. The method is used to estimate and compare biomechanical performance implicated as selective factors in the evolution of morphological structures. A feature common to many comparative studies using 3D FE simulations is small taxonomic sample sizes. The time-consuming nature of FE model construction is considered a main limiting factor in taxonomic breadth of comparative FE analyses. Using a composite FE model dataset, I show that the combination of small taxonomic sample sizes and comparative FE data in analyses of evolutionary associations of biomechanical performance to feeding ecology generates artificially elevated correlations. Such biases introduce false positives into interpretations of clade-level trends. Considering this potential pitfall, recommendations are provided to consider the ways FE analyses are best used to address both taxon-specific and clade-level evolutionary questions.
| S-EPMC8035905 | biostudies-literature
Project description:Internal fixation of bone fractures using plates and screws involves many choices-implant type, material, sizes, and geometric configuration-made by the surgeon. These decisions can be important for providing adequate stability to promote healing and prevent implant mechanical failure. The purpose of this study was to develop mathematical models of the relationships between fracture fixation construct parameters and resulting 3D biomechanics, based on parametric computer simulations. Finite element models of hundreds of different locked plate fixation constructs for midshaft diaphyseal fractures were systematically assembled using custom algorithms, and axial, torsional, and bending loadings were simulated. Multivariate regression was used to fit response surface polynomial equations relating fixation design parameters to outputs including maximum implant stresses, axial and shear strain at the fracture site, and construct stiffness. Surrogate models with as little as three regressors showed good fitting (R 2 = 0.62-0.97). Inner working length was the strongest predictor of maximum plate and screw stresses, and a variety of quadratic and interaction terms influenced resulting biomechanics. The framework presented in this study can be applied to additional types of bone fractures to provide clinicians and implant designers with clinical insight, surgical optimization, and a comprehensive mathematical description of biomechanics.
| S-EPMC6358019 | biostudies-literature
Project description:BACKGROUND:Previous studies have revealed positive effect of Topping-off technique on upper adjacent segment after fusion surgery, while for the cases with fusion surgery on L5-S1 segment, owning maximal range of motion, and preexisting degenerated upper adjacent disc, it is necessary to clarify the superiority of Topping-ff technique and the effect exerted on the lumbar spine. METHODS:A young healthy male volunteer was selected for thin-slice CT scanning. Then the image information was imported into the computer to establish the whole lumbar spine model as the health model. The medium degeneration model of intervertebral disc was established by changing the material properties of L4-S1 disc on the basis of the health model, and the fusion model and Topping-off model were respectively established on the basis of the degenerated model. The variation trend of ROM of L2-L5 and the stress changes of L4-L5 intervertebral disc, nucleus pulposus and facet joints were calculated respectively. RESULTS:The L4-L5 ROM of fusion model increased significantly but the ROM of L2-L3 and L3-L4 segments did not change significantly. Compared with the degenerated model, L4-L5 activity of the Topping-off model decreased, and ROM of the L2-L3 and L3-L4 increased to some extent in the flexion and extension positions. The stress on the disc, nucleus pulposus and facet joint of the fusion model L4-L5 increased in four positions of flexion, extension, rotation and bending compared with the degenerated model, while the fiber stress on the Topping-off model decreased significantly in all four positions. CONCLUSION:Topping-off technology can decrease the stress and ROM of the adjacent upper degenerated segment, and increase the ROM of other upper segments, thereby protecting the degenerated upper adjacent segments and compensating the lumbar spine mobility.
| S-EPMC7023809 | biostudies-literature
Project description:A finite element analysis was performed to evaluate the stresses around nails and cortical bones in subtrochanteric (ST) fracture models fixed using short cephalomedullary nails (CMNs). A total 96 finite element models (FEMs) were simulated on a transverse ST fracture at eight levels with three different fracture gaps and two different distal locking screw configurations in both normal and osteoporotic bone. All FEMs were fixed using CMNs 200 mm in length. Two distal locking screws showed a wider safe range than 1 distal screw in both normal and osteoporotic bone at fracture gaps ≤ 3 mm. In normal bone FEMs fixed even with two distal locking screws, peak von Mises stresses (PVMSs) in cortical bone and nail constructs reached or exceeded 90% of the yield strength at fracture levels 50 mm and 0 and 50 mm, respectively, at all fracture gaps. In osteoporotic bone FEMs, PVMSs in cortical bone and nail constructs reached or exceeded 90% of the yield strength at fracture levels 50 mm and 0 and 50 mm, respectively, at a 1-mm fracture gap. However, at fracture gaps ≥ 2 mm, PVMSs in cortical bone reached or exceeded 90% of the yield strength at fracture levels ≥ 35 mm. PVMSs in nail showed the same results as 1-mm fracture gaps. PVMSs increased and safe range reduced, as the fracture gap increased. Short CMNs (200 mm in length) with two distal screws may be considered suitable for the fixation of ST transverse fractures at fracture levels 10 to 40 mm below the lesser trochanter in normal bone and 10 to 30 mm in osteoporotic bone, respectively, under the assumptions of anatomical reduction at fracture gap ≤ 3 mm. However, the fracture gap should be shortened to the minimum to reduce the risk of refracture and fixation failure, especially in osteoporotic fractures.
| S-EPMC8248632 | biostudies-literature
Project description:Mathematical models for excitable cells are commonly based on cable theory, which considers a homogenized domain and spatially constant ionic concentrations. Although such models provide valuable insight, the effect of altered ion concentrations or detailed cell morphology on the electrical potentials cannot be captured. In this paper, we discuss an alternative approach to detailed modeling of electrodiffusion in neural tissue. The mathematical model describes the distribution and evolution of ion concentrations in a geometrically-explicit representation of the intra- and extracellular domains. As a combination of the electroneutral Kirchhoff-Nernst-Planck (KNP) model and the Extracellular-Membrane-Intracellular (EMI) framework, we refer to this model as the KNP-EMI model. Here, we introduce and numerically evaluate a new, finite element-based numerical scheme for the KNP-EMI model, capable of efficiently and flexibly handling geometries of arbitrary dimension and arbitrary polynomial degree. Moreover, we compare the electrical potentials predicted by the KNP-EMI and EMI models. Finally, we study ephaptic coupling induced in an unmyelinated axon bundle and demonstrate how the KNP-EMI framework can give new insights in this setting.
| S-EPMC7109287 | biostudies-literature