Dataset Information

Biomechanical evaluation of cervical disc replacement with a novel prosthesis based on the physiological curvature of endplate.

ABSTRACT: Most of the current available cervical disc prostheses present a flat surface instead of an arcuate surface which is most similar to the morphology of cervical endplate. Therefore, we designed a novel prosthesis (Pretic-I, Trauson) based on the physiological curvature of the cervical endplate. Biomechanical evaluation of cervical disc replacement (CDR) with this novel prosthesis was performed and compared with the Prestige LP prosthesis.Three motion segments of 18 cadaveric cervical specimens (C2-C7) were evaluated with a 75 N follower load. Overall, the biomechanics of three models, intact specimen, CDR with the novel prosthesis and CDR with the Prestige LP prosthesis, were studied to gain insight into the effective function of the novel prosthesis. The range of motion (ROM) of all three segments and intradiscal pressure (IDP) on adjacent levels were measured and analysed.Compared to the intact condition, the ROM of all three segments showed no significant difference in the replacement group. Moreover, there was also no significant difference in the ROM between the two prostheses. Besides, the IDP on the cranial adjacent level showed no obvious difference between the two prostheses; nevertheless, the IDP on the caudal adjacent level of the novel prosthesis was significantly less than the Prestige LP prosthesis.In summary, the novel disc prosthesis was effective to maintain the ROM at the target segment and adjacent segments. Besides, CDR with the novel prosthesis could reduce the IDP on the caudal adjacent level to a certain extent, compared with the Prestige LP prosthesis.

SUBMITTER: Lou J

PROVIDER: S-EPMC5828121 | biostudies-literature | 2018 Feb

REPOSITORIES: biostudies-literature

ACCESS DATA

Publications

Biomechanical evaluation of cervical disc replacement with a novel prosthesis based on the physiological curvature of endplate.

Lou Jigang J Li Yuanchao Y Wang Beiyu B Meng Yang Y Gong Quan Q Liu Hao H

Journal of orthopaedic surgery and research 20180227 1

<h4>Background</h4>Most of the current available cervical disc prostheses present a flat surface instead of an arcuate surface which is most similar to the morphology of cervical endplate. Therefore, we designed a novel prosthesis (Pretic-I, Trauson) based on the physiological curvature of the cervical endplate. Biomechanical evaluation of cervical disc replacement (CDR) with this novel prosthesis was performed and compared with the Prestige LP prosthesis.<h4>Methods</h4>Three motion segments of ...[more]

PMID: 29482611

Similar Datasets

Project description:BackgroundWhen surgically treating cervical degenerative disc disease, the most commonly performed procedure is anterior cervical discectomy. This procedure is performed with, or without fusion promoting methods. For both options the rate of fusion is high and there is much debate whether fusion of the treated segment is a contributing factor to accelerated degeneration of adjacent motion segments. In an effort to prevent degeneration of adjacent segments (ASDeg) due to loss of mobility at the operated level, cervical disc arthroplasty (CDA) was introduced. To evaluate the effectiveness of CDA in preventing ASDeg long term studies are necessary. However, prevention of ASDeg is based on the premise that mobile disc prostheses preserve cervical spine motion in a physiological way. In this article the authors describe a short term protocol for a study that aims to investigate whether CDA reaches the intended goal: restoration or preservation of physiological cervical spine motion. To this end, a technique is used to establish the sequence of contributions of cervical motion segments to flexion/extension of the spine.Methods24 subjects between 18 and 55 years old, with radicular symptoms due to a herniated disc between C5 and C7, refractory to conservative therapy are randomized to simple discectomy, or CDA. These groups are preceded by a pilot group of three subjects receiving CDA. Fluoroscopic flexion-extension recordings are acquired preoperatively, and at three and 12 months postoperative. At these same time points, patient reported outcomes are collected, and a neurological examination is performed by and independent physician.DiscussionStudies investigating arthroplasty determine mobility by measuring segmental range of motion (sROM), which gives no information other than presence, and quantity, of mobility. SROM suffer from high variability. The authors therefore chose to use a method previously used in healthy controls, to describe the dynamic process of cervical spine motion in more detail. Determining cervical spine motion patterns has been reported to be more consistent than sROM. If a physiological motion pattern is absent after surgery in the CDA group, prevention of future ASDeg is less likely. Radiological outcomes will be correlated to clinical outcomes.Trial registrationNCT00868335.

Project description:Biological approaches to intervertebral disc (IVD) restoration and/or regeneration have become of increasing interest. However, the IVD comprises a viscoelastic system whose biological replacement remains challenging. The present study sought to design load-sharing two-component model systems of circular, nested, concentric elements reflecting the nucleus pulposus and annulus fibrosus. Specifically, we wanted to investigate the effect of architectural design variations on (1) model system failure loads when testing the individual materials either separately or homogeneously mixed, and (2) also evaluate the potential of modulating other mechanical properties of the model systems. Two sets of softer and harder biomaterials, 0.5% and 5% agarose vs. 0.5% agarose and gelatin, were used for fabrication. Architectural design variations were realized by varying ring geometries and amounts while keeping the material composition across designs comparable. Variations in the architectural design, such as lamellar width, number, and order, combined with choosing specific biomaterial properties, strongly influenced the biomechanical performance of IVD constructs. Biomechanical characterization revealed that the single most important parameter, in which the model systems vastly exceeded those of the individual materials, was failure load. The model system failure loads were 32.21- and 84.11-fold higher than those of the agarose materials and 55.03- and 2.14-fold higher than those of the agarose and gelatin materials used for system fabrication. The compressive strength, dynamic stiffness, and viscoelasticity of the model systems were always in the range of the individual materials. Relevant architecture-promoted biomechanical performance-tuning of tissue-engineered constructs for biological IVD replacement can be realized by slight modifications in the design of constructs while preserving the materials' compositions. Minimal variations in the architectural design can be used to precisely control structure-function relations for IVD constructs rather than choosing different materials. These fundamental findings have important implications for efficient tissue-engineering of IVDs and other load-bearing tissues, as potential implants need to withstand high in situ loads.

Dataset Information

Biomechanical evaluation of cervical disc replacement with a novel prosthesis based on the physiological curvature of endplate.

Publications

Biomechanical evaluation of cervical disc replacement with a novel prosthesis based on the physiological curvature of endplate.

Similar Datasets

OmicsDI is part of the ELIXIR infrastructure

Tweets