Dataset Information

Visualization method for stress-field evolution during rapid crack propagation using 3D printing and photoelastic testing techniques.

ABSTRACT: Quantitative visualization and characterization of stress-field evolution during fracture rapid growth is critical for understanding the mechanisms that govern the deformation and failure of solids in various engineering applications. However, the direct capture and accurate characterization of a rapidly-changing stress field during crack propagation remains a challenge. We report an experimental method to quantitatively visualize and characterize rapid evolution of the stress-field during crack propagation in a transparent disc model containing a penetrating fusiform crack. Three-dimensional (3D) printing technology and a stress-sensitive photopolymer resin were adopted to produce the disc model and to alleviate the residual processing stress that usually blurs the dynamic stress field due to overlap. A photoelastic testing system that synchronized a high-speed digital camera and a pulsed laser with a nanosecond full width at half maximum (FWHM) was used to capture the rapid evolution of the stress field in the vicinity of crack tips. The results show that the proposed method is suitable to directly visualize and quantitatively characterize the stress-field evolution during crack rapid propagation. It is proved that the crack propagation velocity is strongly governed by the stress field around the crack tips.

SUBMITTER: Ju Y

PROVIDER: S-EPMC5847554 | biostudies-literature | 2018 Mar

REPOSITORIES: biostudies-literature

ACCESS DATA

Publications

Visualization method for stress-field evolution during rapid crack propagation using 3D printing and photoelastic testing techniques.

Ju Yang Y Xie Heping H Zhao Xi X Mao Lingtao L Ren Zhangyu Z Zheng Jiangtao J Chiang Fu-Pen FP Wang Yongliang Y Gao Feng F

Scientific reports 20180312 1

Quantitative visualization and characterization of stress-field evolution during fracture rapid growth is critical for understanding the mechanisms that govern the deformation and failure of solids in various engineering applications. However, the direct capture and accurate characterization of a rapidly-changing stress field during crack propagation remains a challenge. We report an experimental method to quantitatively visualize and characterize rapid evolution of the stress-field during crack ...[more]

PMID: 29531306

Similar Datasets

Project description:BackgroundIt is known that a number of parameters can influence the post-printing properties of bone tissue scaffolds. Previous research has primarily focused on the effect of parameters associated with scaffold design (e.g., scaffold porosity) and specific scaffold printing processes (e.g., printing pressure). To our knowledge, no studies have investigated variations in post-printing properties attributed to the techniques used to synthesize the materials for printing (e.g., melt-blending, powder blending, liquid solvent, and solid solvent).MethodsFour material preparation techniques were investigated to determine their influence on scaffold properties. Polycaprolactone/nano-hydroxyapatite 30% (wt.) materials were synthesized through melt-blending, powder blending, liquid solvent, and solid solvent techniques. The material printability and the properties of printed scaffolds, in terms of swelling/degradation, mechanical strength, morphology, and thermal properties, were examined and compared to one another using Kruskal-Wallis nonparametric statistical analysis.ResultsMaterial prepared through the liquid solvent technique was found to have limited printability, while melt-blended material demonstrated the highest degree of uniformity and lowest extent of swelling and degradation. Scaffolds prepared with powder-blended material demonstrated the highest Young's modulus, yield strength, and modulus of resilience; however, they also demonstrated the highest degree of variability. The higher degree of inhomogeneity in the material was further supported by thermal gravimetric analysis. While scaffolds printed from melt-blended, powder-blended, and solid solvent materials demonstrated a high degree of micro-porosity, the liquid solvent material preparation technique resulted in minimal micro-porosity.ConclusionsStudy results indicate that specific techniques used to prepare materials influence the printing process and post-printing scaffold properties. Among the four techniques examined, melt-blended materials were found to be the most favorable, specifically when considering the combination of printability, consistent mechanical properties, and efficient preparation. Techniques determined to be favourable based on the properties investigated should undergo further studies related to biological properties and time-dependent properties beyond 21-days.

Project description:OBJECTIVE:To explore the application of 3D visualization and 3D printing in individualized precision surgical treatment of Bismuth-Corlette type ? and ? hilar cholangiocarcinoma. METHODS:We retrospectively analyzed the data of 10 patients with hilar cholangiocarcinoma undergoing surgeries under the guidance of 3D visualization and 3D printing in the Department of Hepatobiliary Surgery, Zhujiang Hospital from May 2016 to March 2019. Thin-section CT data of the patients were collected for 3D reconstruction and 3D printing, and the 3D printed models were used for observing the 3D relationship of tumor with the intrahepatic bile duct, hepatic artery, portal vein and hepatic vein system and for performing preoperative simulated surgery and surgical planning. The 3D printed models were subsequently used for real-time intraoperative navigation to guide surgeries in the operating room. RESULTS:3D visualization models were successfully reconstructed for all the 10 patients and printed into 3D models. The 3D visualization types in Bismuth-Corlette classification included type ?a (4 cases), type ?b (4 cases), and type ? (2 cases); 4 patients showed portal vein variation, 3 had hepatic artery variation, and 2 had both portal vein and hepatic artery variations. Two patients were found to have trifurcation type of portal vein variation, one had "I-shaped" variation, and one showed the absence of the right anterior branch of the portal vein; 3 patients had hepatic artery variations with the left hepatic artery originating from the left gastric artery (1 case) and the right hepatic artery originating from the superior mesenteric artery (2 cases). Four patients with type ?b underwent left hepatectomy; 4 with type ?a received right hepatectomy; 1 patient with of type ? received peripheral hepatic resection and another underwent left hepatectomy. The results of preoperative 3D reconstruction, 3D printed model and preoperative planning were consistent with the intraoperative findings. The operative time was 452±75.12 min with a mean intraoperative blood loss of 356±62.35 mL and a mean hospital stay of 15 ± 4.61 days in these cases. One patient had bile leakage and 3 patients had pleural effusion postoperatively, and they were discharged after drainage and medications. No liver failure or death occurred in these cases perioperatively. CONCLUSIONS:3D visualization and 3D printing can facilitate accurate preoperative assessment, surgical planning and surgical procedure optimization for Bismuth-Corlette type ? and ? hilar cholangiocarcinoma to improve surgical safety and reduce surgical risks especially in cases of intrahepatic vascular variations.

Dataset Information

Visualization method for stress-field evolution during rapid crack propagation using 3D printing and photoelastic testing techniques.

Publications

Visualization method for stress-field evolution during rapid crack propagation using 3D printing and photoelastic testing techniques.

Similar Datasets

OmicsDI is part of the ELIXIR infrastructure

Tweets