Browse
Submit Data
Databases
API
Help

Dataset Information

0 Views

0 Connections

0 Citations

0 Reanalyses

0 Downloads

Omics score: 0

Al6061 surface roughness and optical reflectance when machined by single point diamond turning at a low feed rate.

ABSTRACT: Ultra-precision face turning of Al6061 mirrors using single point diamond turning (SPDT) was undertaken to investigate the correlation between the surface roughness and reflectance. By reducing the feed rate, the optimal feed rate when the chip formation became unstable was studied. Most importantly, the impact on the roughness and reflectance was examined when the chip formation ceased to be continuous. It was determined that for a feed rate below 3 mm/min, the surface roughness always improved as the feed rate decreased, at the cost of a reduction of the normalized reflectance. The reduction of reflectance was determined to be the result of the lower material removal rates that led to a discontinuous chip formation.

SUBMITTER: Li LH

PROVIDER: S-EPMC5880365 | biostudies-literature | 2018

REPOSITORIES: biostudies-literature

ACCESS DATA

Json Xml

Publications

Al6061 surface roughness and optical reflectance when machined by single point diamond turning at a low feed rate.

Li L H LH Yu N H NH Chan C Y CY Lee W B WB

PloS one 20180402 4

Ultra-precision face turning of Al6061 mirrors using single point diamond turning (SPDT) was undertaken to investigate the correlation between the surface roughness and reflectance. By reducing the feed rate, the optimal feed rate when the chip formation became unstable was studied. Most importantly, the impact on the roughness and reflectance was examined when the chip formation ceased to be continuous. It was determined that for a feed rate below 3 mm/min, the surface roughness always improved ...[more]

PMID: 29608580

Similar Datasets

Swept Mechanism of Micro-Milling Tool Geometry Effect on Machined Oxygen Free High Conductivity Copper (OFHC) Surface Roughness.

Project description:Cutting tool geometry should be very much considered in micro-cutting because it has a significant effect on the topography and accuracy of the machined surface, particularly considering the uncut chip thickness is comparable to the cutting edge radius. The objective of this paper was to clarify the influence of the mechanism of the cutting tool geometry on the surface topography in the micro-milling process. Four different cutting tools including two two-fluted end milling tools with different helix angles of 15° and 30° cutting tools, as well as two three-fluted end milling tools with different helix angles of 15° and 30° were investigated by combining theoretical modeling analysis with experimental research. The tool geometry was mathematically modeled through coordinate translation and transformation to make all three cutting edges at the cutting tool tip into the same coordinate system. Swept mechanisms, minimum uncut chip thickness, and cutting tool run-out were considered on modeling surface roughness parameters (the height of surface roughness Rz and average surface roughness Ra) based on the established mathematical model. A set of cutting experiments was carried out using four different shaped cutting tools. It was found that the sweeping volume of the cutting tool increases with the decrease of both the cutting tool helix angle and the flute number. Great coarse machined surface roughness and more non-uniform surface topography are generated when the sweeping volume increases. The outcome of this research should bring about new methodologies for micro-end milling tool design and manufacturing. The machined surface roughness can be improved by appropriately selecting the tool geometrical parameters.

| S-EPMC5459116 | biostudies-other

A Polycrystalline Pd Surface Studied by Two-Dimensional Surface Optical Reflectance during CO Oxidation: Bridging the Materials Gap.

Project description:Industrial catalysts are complex materials systems operating in harsh environments. The active parts of the catalysts are nanoparticles that expose different facets with different surface orientations at which the catalytic reactions occur. However, these facets are close to impossible to study in detail under industrially relevant operating conditions. Instead, simpler model systems, such as single crystals with a well-defined surface orientation, have been successfully used to study gas-surface interactions such as adsorption and desorption, surface oxidation, and oxidation/reduction reactions. To more closely mimic the many facets exhibited by nanoparticles and thereby close the so-called materials gap, there has also been a recent move toward using polycrystalline surfaces and curved crystals. However, these studies are limited either by the pressure or spatial resolution at realistic pressures or by the number of surfaces studied simultaneously. In this work, we demonstrate the use of reflectance microscopy to study a vast number of catalytically active surfaces simultaneously under realistic and identical reaction conditions. As a proof of concept, we have conducted an operando experiment to study CO oxidation over a Pd polycrystal, where the polycrystalline surface acts as a collection of many single-crystal surfaces. Finally, we visualized the resulting data by plotting the reflectivity as a function of surface orientation. We think the techniques and visualization methods introduced in this work will be key toward bridging the materials gap in catalysis.

| S-EPMC10788831 | biostudies-literature

Effects of Shape, Roughness and Gloss on the Perceived Reflectance of Colored Surfaces.

Project description:This study examined perceptual differentiation of specular from diffuse shading for the recovery of surface color and gloss. In Experiment 1, we parametrically varied the mesoscale relief height of globally planar surfaces, specular sharpness and the orientation of the surface relative to the light source. We obtained psychophysical matches for perceived color saturation and value (HSV), but also considered whether the main effects could be influenced by color space used when transforming data to perceptually-uniform CIE LCH space. Results revealed strong interactions between perceived color attributes and the lighting conditions, the structure of specular reflections, and surface relief. Declines in saturation were observed with increasing specular roughness (using an HSV color representation), but no similar decline was observed in chroma (using a CIE LCH color representation). Experiment 2 found strong negative correlations between perceived gloss and specular roughness. Perceived gloss also depended on mesoscopic relief height and orientation of the surface relative to the light source. Declines in perceived gloss moderately accounted for the variability in color saturation and value matches obtained in Experiment 1. We found information about perceived specular coverage could further improve the model's accountability of perceived color saturation and lightness (Experiment 3). These findings together suggest that perceived color saturation and color value depends on the visual system's ability to distinguish the underlying diffuse shading from specular highlights in images.

| S-EPMC7101081 | biostudies-literature

Assessment of CVD- and PVD-Coated Carbides and PVD-Coated Cermet Inserts in the Optimization of Surface Roughness in Turning of AISI 1045 Steel.

Project description:In this study, an experimental and statistic investigation approach based on analysis of variance (ANOVA) and response surface methodology (RSM) techniques was performed to find the significant main effects and two-factor interaction effects and to determine how the controllable factors such as cutting speed, feed rate, depth of cut (DOC), tool nose radius, substrate and coating method of cutting tools influence surface quality in turning of AISI 1045 steel. The first optimal or near-optimal conditions for the quality of the generated surface and the second ones, including maximum material removal rate, were established using the proposed regression equations. The group mean roughness of the turned workpieces was lower from using chemical vapor deposition (CVD)-coated carbide inserts than the group means of other types of inserts; however they could not achieve the specific lowest roughness. The physical vapor deposition (PVD)-coated carbide and cermet inserts achieved the best surface quality when the specific combinations within the range interval of controllable factors were used in the experiment, showing that they may be applied to finish turning processes or even to particular high material removal rate conditions associated with the lowest roughness.

| S-EPMC7699436 | biostudies-literature

Silicone Implant Surface Roughness, Friction, and Wear.

Project description:Textured silicone breast implants with high average surface roughness ("macrotextured") have been associated with a rare cancer of the immune system, Breast Implant-Associated Anaplastic Large Cell Lymphoma (BIA-ALCL). Silicone elastomer wear debris may lead to chronic inflammation, a key step in the development of this cancer. Here, we model the generation and release of silicone wear debris in the case of a folded implant-implant ("shell-shell") sliding interface for three different types of implants, characterized by their surface roughness. The "smooth" implant shell with the lowest average surface roughness tested (Ra = 2.7 ± 0.6 μm) resulted in average friction coefficients of μavg = 0.46 ± 0.11 across 1,000 mm of sliding distance and generated 1,304 particles with an average particle diameter of Davg = 8.3 ± 13.1 μm. The "microtextured" implant shell (Ra = 32 ± 7.0 μm) exhibited μavg = 1.20 ± 0.10 and generated 2,730 particles with Davg = 4.7 ± 9.1 μm. The "macrotextured" implant shell (Ra = 80 ± 10 μm) exhibited the highest friction coefficients, μavg = 2.82 ± 0.15 and the greatest number of wear debris particles, 11,699, with an average particle size of Davg = 5.3 ± 3.3 μm. Our data may provide guidance for the design of silicone breast implants with lower surface roughness, lower friction, and smaller quantities of wear debris.

| S-EPMC10181813 | biostudies-literature

Turning Point in the Treatment of Mantle Cell Lymphoma.

Project description:Mantle cell lymphoma (MCL) is an incurable type of B-cell lymphoma. It is typically composed of small-to-medium-sized cleaved lymphoid cells with cyclin D1 protein expression due to the chromosomal translocation t(11;14)(q13;q32). Even with the development of rituximab, an anti-CD20 antibody drug, the long-term outcome of patients with MCL has not improved. Recently, new agents have been used in clinical settings, and the outcome of patients with MCL is expected to improve. The treatment of MCL may be at a turning point from intensive chemotherapy to chemotherapy-free treatment. In this study, a recent progress in the diagnosis and treatment of MCL is reviewed.

| S-EPMC6437406 | biostudies-literature

Estimating Nanoscale Surface Roughness of Polyethylene Terephthalate Fibers.

Project description:Quantitation of surface roughness is difficult, if subtle, but significant differences cause an uncommon variance. We used atomic force microscopy to measure the surface roughness of polyethylene terephthalate (PET) fibers before and after a 30 s plasma treatment of 300 W. Samples were measured multiple times at different locations, in four scan sizes. The surface roughness was expressed in terms of nine roughness parameters. Despite the large number of data, simple statistics was not able to detect significant differences in roughness before and after plasma treatment. A factorial analysis of variance (ANOVA) of the normalized data and a sum of ranking differences analysis using four types of data preprocessing and their factorial ANOVA confirmed that (i) the plasma treatment had roughened the PET fiber surface; (ii) the roughness increases with the scanned area in the measured range; and (iii) what the best roughness parameters are in discriminating between surfaces before and after treatment. Although the compared roughness estimators were on different scales, a roughness estimation of the nanoscale surfaces was feasible, where other methods fail. The presented methodology can be applied widely and unambiguously for highly different method comparison tasks.

| S-EPMC7045555 | biostudies-literature

Impact of surface roughness on liquid-liquid transition.

Project description:Liquid-liquid transition (LLT) in single-component liquids is one of the most mysterious phenomena in condensed matter. So far, this problem has attracted attention mainly from the fundamental viewpoint. We report the first experimental study on an impact of surface nanostructuring on LLT by using a surface treatment called rubbing, which is the key technology for the production of liquid crystal displays. We find that this rubbing treatment has a significant impact on the kinetics of LLT of an isotropic molecular liquid, triphenyl phosphite. For a liquid confined between rubbed surfaces, surface-induced barrierless formation of the liquid II phase is observed even in a metastable state, where there should be a barrier for nucleation of the liquid II phase in bulk. Thus, surface rubbing of substrates not only changes the ordering behavior but also significantly accelerates the kinetics. This spatiotemporal pattern modulation of LLT can be explained by a wedge-filling transition and the resulting drastic reduction of the nucleation barrier. However, this effect completely disappears in the unstable (spinodal) regime, indicating the absence of the activation barrier even for bulk LLT. This confirms the presence of nucleation-growth- and spinodal decomposition-type LLT, supporting the conclusion that LLT is truly a first-order transition with criticality. Our finding also opens up a new way to control the kinetics of LLT of a liquid confined in a solid cell by structuring its surface on a mesoscopic length scale, which may contribute to making LLT useful for microfluidics and other industrial applications.

| S-EPMC5315451 | biostudies-literature

Combinatorial Surface Roughness Effects on Osteoclastogenesis and Osteogenesis.

Project description:Implant surface properties are a key factor in bone responses to metallic bone implants. In view of the emerging evidence on the important role of osteoclasts in bone regeneration, we here studied how surface roughness affects osteoclastic differentiation and to what extent these osteoclasts have stimulatory effects on osteogenic differentiation of osteoprogenitor cells. For this, we induced osteoclasts derived from RAW264.7 cell line and primary mouse macrophages on titanium surfaces with different roughness ( Ra 0.02-3.63 μm) and analyzed osteoclast behavior in terms of cell number, morphology, differentiation, and further anabolic effect on osteoblastic cells. Surfaces with different roughness induced the formation of osteoclasts with distinct phenotypes, based on total osteoclast numbers, morphology, size, cytoskeletal organization, nuclearity, and osteoclastic features. Furthermore, these different osteoclast phenotypes displayed differential anabolic effects toward the osteogenic differentiation of osteoblastic cells, for which the clastokine CTHRC1 was identified as a causative factor. Morphologically, osteoclast potency to stimulate osteogenic differentiation of osteoblastic cells was found to logarithmically correlate with the nuclei number per osteoclast. Our results demonstrate the existence of a combinatorial effect of surface roughness, osteoclastogenesis, and osteogenic differentiation. These insights open up a new dimension for designing and producing metallic implants by considering the implant roughness to locally regulate osseointegration through coupling osteoclastogenesis with osteogenesis.

| S-EPMC6213029 | biostudies-literature

Objective quantification of surface roughness parameters affecting superhydrophobicity.

Project description:This study proposes new optical roughness parameters that can be objectively quantified using image processing techniques, and presents an analysis of how these parameters are correlated with the degree of superhydrophobicity. To this end, photolithography and dry etching processes were used to form regular square pillars with different heights and spacings with a length of tens of micro-meters on silicon wafers. Optical roughness parameters of the specimens were obtained using image processing, and surface wettability was characterized using static contact angle and sliding angle measurements for water droplets of volume V D = 3.5 μl or 12 μl. As a result, seven optical roughness parameters were derived to describe the surface roughness topography in a multi-faceted way. Between the Cassie-Baxter state and the Wenzel state, two distinct wetting states intermediate state I, and intermediate state II were observed. Multiple linear regression of optical roughness parameters and superhydrophobicity demonstrated that in the stable Cassie-Baxter state, the contact angle can be increased or sliding angle decreased more effectively by adjusting the spacing between pillars than by just tuning the solid area fraction. However, in the metastable state where the Cassie-Baxter state can be changed to intermediate state I and vice versa by adjusting V D or surface geometry, reducing the solid area fraction is a priority to ensure a stable Cassie-Baxter state. Horizontal-perspective roughness parameters had a great effect on dynamic wettability in the Cassie-Baxter state. The results confirmed that the proposed optical roughness parameters may be useful for quantitative analysis of the complex effects of roughness on superhydrophobic surfaces.

| S-EPMC9056393 | biostudies-literature

OmicsDI is part of the ELIXIR infrastructure

OmicsDI is an Elixir interoperability service. Learn more ›

Tweets

OmicsDI Databases

PRIDE
PeptideAtlas
MassIVE
JPOST Repository
Physiome Model Repository

EGA
EVA
ENA
LINCS
PAXDB
Cell Collective

MetaboLights
Metabolomics Workbench
MetabolomeExpress
GNPS
BioModels
FAIRDOMHub

ArrayExpress
dbGaP
ExpressionAtlas
GEO
NODE

Information

Databases
Help
API
Contact us
Code on GitHub
Terms of use
Submit Data