Dataset Information

Investigation of a potential HCHO measurement artifact from ISOPOOH.

ABSTRACT: Recent laboratory experiments have shown that a first generation isoprene oxidation product, ISOPOOH, can decompose to methyl vinyl ketone (MVK) and methacrolein (MACR) on instrument surfaces, leading to overestimates of MVK and MACR concentrations. Formaldehyde (HCHO) was suggested as a decomposition co-product, raising concern that in situ HCHO measurements may also be affected by an ISOPOOH interference. The HCHO measurement artifact from ISOPOOH for the NASA In Situ Airborne Formaldehyde instrument (ISAF) was investigated for the two major ISOPOOH isomers, (1,2)-ISOPOOH and (4,3)-ISOPOOH, under dry and humid conditions. The dry conversion of ISOPOOH to HCHO was 3±2% and 6±4% for (1,2)-ISOPOOH and (4,3)-ISOPOOH, respectively. Under humid (RH= 40-60%) conditions, conversion to HCHO was 6±4% for (1,2)-ISOPOOH and 10±5% for (4,3)-ISOPOOH. The measurement artifact caused by conversion of ISOPOOH to HCHO in the ISAF instrument was estimated for data obtained on the 2013 September 6 flight of the Studies of Emissions and Atmospheric Composition, Clouds and Climate Coupling by Regional Surveys (SEAC4RS) campaign. Prompt ISOPOOH conversion to HCHO was the source for <4% of the observed HCHO, including in the high-isoprene boundary layer. Time-delayed conversion, where previous exposure to ISOPOOH affects measured HCHO later in flight, was conservatively estimated to be < 10% of observed HCHO and is significant only when high ISOPOOH sampling periods immediately precede periods of low HCHO.

SUBMITTER: St Clair JM

PROVIDER: S-EPMC5889939 | biostudies-literature | 2016

REPOSITORIES: biostudies-literature

ACCESS DATA

Publications

Investigation of a potential HCHO measurement artifact from ISOPOOH.

St Clair Jason M JM Rivera-Rios Jean C JC Crounse John D JD Praske Eric E Kim Michelle J MJ Wolfe Glenn M GM Keutsch Frank N FN Wennberg Paul O PO Hanisco Thomas F TF

Atmospheric measurement techniques 20160916 9

Recent laboratory experiments have shown that a first generation isoprene oxidation product, ISOPOOH, can decompose to methyl vinyl ketone (MVK) and methacrolein (MACR) on instrument surfaces, leading to overestimates of MVK and MACR concentrations. Formaldehyde (HCHO) was suggested as a decomposition co-product, raising concern that in situ HCHO measurements may also be affected by an ISOPOOH interference. The HCHO measurement artifact from ISOPOOH for the NASA In Situ Airborne Formaldehyde ins ...[more]

PMID: 29636831

Similar Datasets

Project description:BackgroundPostnatal care (PNC) for mothers and newborns is essential to monitor risks of morbidity and adverse conditions following delivery. Current estimates of the coverage of PNC show substantial discordance between mothers and newborns. We investigate the sources of this discordance in Demographic and Health Surveys (DHS).MethodsWe used DHS data from 48 countries collected since 2011, spanning phases 6 and 7 of the survey program with 32 and 16 surveys, respectively, analyzed. We assessed the distribution of the reported timing of PNC and conducted a sensitivity analysis that excludes/includes PNC reported within 0-1 hour or PNC in the day 2. Agreement in PNC reporting considered four groups: (1) Concordance, neither mother nor newborn received PNC; (2) Concordance, mother and newborn pair received PNC; (3) Discordance, mother received PNC and newborn did not; of (4) Discordance, mother did not receive PNC but the newborn did. We carried out logistic regressions to understand correlates of PNC discordance. All analyses distinguished phase 6 surveys from phase 7.ResultsWe found substantial differences in the PNC coverage estimated between phase 6 and phase 7 surveys. The phase 7 PNC questions for newborns were improved to increase the understanding of the questions by respondent which probably led to reducing the large PNC gap between mothers and newborns observed in phase 6 surveys. With phase 6 surveys, PNC coverage for mother was estimated on average at 62% compared to only 31% for newborns. No such gap was observed for phase 7 surveys, where for both mothers and newborns, the PNC coverage estimate was similar, at 56%. For both phases, over half of the reported PNC for mothers and newborns occurred during 0-1 hour following delivery, leading to substantial overestimation of PNC coverage, due to confusion between intrapartum care and PNC. There were 37% discordant cases between mother and newborn, largely in favor of the mother in phase 6 surveys, compared to 16% in phase 7 surveys. In phase 6 surveys, discordant PNC cases were observed largely among facility deliveries vs non-facility deliveries (44% compared to 19%).ConclusionsCurrent estimates of coverage of PNC from DHS phase 6 surveys appears to include substantial level of measurement noises that could explain substantial part of the mother-newborn discordance in PNC. The PNC estimates appear to capture a substantial number of intrapartum care. Current measurement approaches warrant further validation to ensure accurate monitoring of the PNC programs.

Project description:Combined positron emission tomography (PET) and magnetic resonance imaging (MRI) targeting the prostate-specific membrane antigen (PSMA) with a 68Ga-labelled PSMA-analog (68Ga-PSMA-11) is discussed as a promising diagnostic method for patients with suspicion or history of prostate cancer. One potential drawback of this method are severe photopenic (halo-) artifacts surrounding the bladder and the kidneys in the scatter-corrected PET images, which have been reported to occur frequently in clinical practice. The goal of this work was to investigate the occurrence and impact of these artifacts and, secondly, to evaluate variants of the standard scatter correction method with regard to halo-artifact suppression.Experiments using a dedicated pelvis phantom were conducted to investigate whether the halo-artifact is modality-, tracer-, and/or concentration-dependent. Furthermore, 31 patients with history of prostate cancer were selected from an ongoing 68Ga-PSMA-11-PET/MRI study. For each patient, PET raw data were reconstructed employing six different variants of PET scatter correction: absolute scatter scaling, relative scatter scaling, and relative scatter scaling combined with prompt gamma correction, each of which was combined with a maximum scatter fraction (MaxSF) of MaxSF = 75% or MaxSF = 40%. Evaluation of the reconstructed images with regard to halo-artifact suppression was performed both quantitatively using statistical analysis and qualitatively by two independent readers.The phantom experiments did not reveal any modality-dependency (PET/MRI vs. PET/CT) or tracer-dependency (68Ga vs. 18F-FDG). Patient- and phantom-based data indicated that halo-artifacts derive from high organ-to-background activity ratios (OBR) between bladder/kidneys and surrounding soft tissue, with a positive correlation between OBR and halo size. Comparing different variants of scatter correction, reducing the maximum scatter fraction from the default value MaxSF = 75% to MaxSF = 40% was found to efficiently suppress halo-artifacts in both phantom and patient data. In 1 of 31 patients, reducing the maximum scatter fraction provided new PET-based information changing the patient's diagnosis.Halo-artifacts are particularly observed for 68Ga-PSMA-11-PET/MRI due to 1) the biodistribution of the PSMA-11-tracer resulting in large OBRs for bladder and kidneys and 2) inaccurate scatter correction methods currently used in clinical routine, which tend to overestimate the scatter contribution. If not compensated for, 68Ga-PSMA-11 uptake pathologies may be masked by halo-artifacts leading to false-negative diagnoses. Reducing the maximum scatter fraction was found to efficiently suppress halo-artifacts.

Project description:Detector lag, or residual signal, in amorphous silicon (a-Si) flat-panel (FP) detectors can cause significant shading artifacts in cone-beam computed tomography (CBCT) reconstructions. To date, most correction models have assumed a linear, time-invariant (LTI) model and lag is corrected by deconvolution with an impulse response function (IRF). However, there are many ways to determine the IRF. The purpose of this work is to better understand detector lag in the Varian 4030CB FP and to identify the IRF measurement technique that best removes the CBCT shading artifact.We investigated the linearity of lag in a Varian 4030CB a-Si FP operating in dynamic gain mode at 15 frames per second by examining the rising step-response function (RSRF) followed by the falling step-response function (FSRF) at ten incident exposures (0.5%-84% of a-Si FP saturation exposure). We implemented a multiexponential (N = 4) LTI model for lag correction and investigated the effects of various techniques for determining the IRF such as RSRF versus FSRF, exposure intensity, length of exposure, and spatial position. The resulting IRFs were applied to (1) the step-response projection data and (2) CBCT acquisitions of a large pelvic phantom and acrylic head phantom. For projection data, 1st and 50th frame lags were measured pre- and postcorrection. For the CBCT reconstructions, four pairs of ROIs were defined and the maximum and mean errors within each pair were calculated for the different exposures and step-response edge techniques.A nonlinearity greater than 50% was observed in the FSRF data. A model calibrated with RSRF data resulted in overcorrection of FSRF data. Conversely, models calibrated with FSRF data applied to RSRF data resulted in undercorrection of the RSRF. Similar effects were seen when LTI models were applied to data collected at different incident exposures. Some spatial variation in lag was observed in the step-response data. For CBCT reconstructions, an average error range of 3-21 HU was observed when using IRFs from different techniques. For our phantoms and FP, the lowest average error occurred for the FSRF-based techniques at exposures of 1.6 or 3.4% a-Si FP saturation, depending on the phantom used.The choice of step-response edge (RSRF versus FSRF) and exposure intensity for IRF calibration could leave large residual lag in the step-response data. For the CBCT reconstructions, IRFs derived from FSRF data at low exposure intensities (1.6 and 3.4%) best removed the CBCT shading artifact. Which IRF to use for lag correction could be selected based on the object size.

Dataset Information

Investigation of a potential HCHO measurement artifact from ISOPOOH.

Publications

Investigation of a potential HCHO measurement artifact from ISOPOOH.

Similar Datasets

OmicsDI is part of the ELIXIR infrastructure

Tweets