Stabilization of fault slip by fluid injection in the laboratory and in situ.
Ontology highlight
ABSTRACT:
SUBMITTER: Cappa F
PROVIDER: S-EPMC6415952 | biostudies-literature | 2019 Mar
REPOSITORIES: biostudies-literature
Publications
Stabilization of fault slip by fluid injection in the laboratory and in situ.
Cappa Frédéric F Scuderi Marco Maria MM Collettini Cristiano C Guglielmi Yves Y Avouac Jean-Philippe JP
Science advances 20190313 3
Faults can slip seismically or aseismically depending on their hydromechanical properties, which can be measured in the laboratory. Here, we demonstrate that fault slip induced by fluid injection in a natural fault at the decametric scale is quantitatively consistent with fault slip and frictional properties measured in the laboratory. The increase in fluid pressure first induces accelerating aseismic creep and fault opening. As the fluid pressure increases further, friction becomes mainly rate ...[more]
Similar Datasets
Project description:The effect of normal stress variations on fault frictional strength has been extensively characterized in laboratory experiments and modelling studies based on a rate-and-state-dependent fault friction formalism. However, the role of pore pressure changes during injection-induced fault reactivation and associated frictional phenomena is still not well understood. We apply rate-and-state friction (RSF) theory in finite element models to investigate the effect of fluid pressurization rate on fault (re)activation and on the resulting frictional slip characteristics at the laboratory scale. We consider a stepwise injection scenario where each fluid injection cycle consists of a fluid pressurization phase followed by a constant fluid pressure phase. We first calibrate our model formulation to recently published laboratory results of injection-driven shear slip experiments. In a second stage, we perform a parametric study by varying fluid pressurization rates to cover a higher dimensional parameter space. We demonstrate that, for high permeability laboratory samples, the energy release rate associated with fault reactivation can be effectively controlled by a stepwise fluid injection scheme, i.e. by the applied fluid pressurization rate and the duration of the constant pressure phase between each successive fluid pressurization phase. We observe a gradual transition from fault creep to slow stick-slip as the fluid pressurization rate increases. Furthermore, computed peak velocities for an extended range of fluid pressurization rate scenarios (0.5 MPa/min to 10 MPa/min) indicate a non-linear (power-law) relationship between the imposed fluid pressurization rate and the peak slip velocities, and consequently with the energy release rate, for scenarios with a fluid pressurization rate higher than a critical value of 4 MPa/min. We also observe that higher pressurization rates cause a delay in the stress release by the fault. We therefore argue that by adopting a stepwise fluid injection scheme with lower fluid pressurization rates may provide the operator with a better control over potential induced seismicity. The implications for field-scale applications that we can derive from our study are limited by the high matrix and fault permeability of the selected sample and the direct hydraulic connection between the injection well and the fault, which may not necessarily represent the conditions typical for fracture dominated deep geothermal reservoirs. Nevertheless, our results can serve as a basis for further laboratory experiments and field-scale modelling studies focused on better understanding the impact of stepwise injection protocols on fluid injection-induced seismicity.
| S-EPMC10023684 | biostudies-literature
Project description:A non-contact, wideband method of sensing dynamic fault slip in laboratory geophysical experiments employs an inexpensive magnetoresistive sensor, a small neodymium rare earth magnet, and user built application-specific wideband signal conditioning. The magnetoresistive sensor generates a voltage proportional to the changing angles of magnetic flux lines, generated by differential motion or rotation of the near-by magnet, through the sensor. The performance of an array of these sensors compares favorably to other conventional position sensing methods employed at multiple locations along a 2 m long × 0.4 m deep laboratory strike-slip fault. For these magnetoresistive sensors, the lack of resonance signals commonly encountered with cantilever-type position sensor mounting, the wide band response (DC to ? 100 kHz) that exceeds the capabilities of many traditional position sensors, and the small space required on the sample, make them attractive options for capturing high speed fault slip measurements in these laboratory experiments. An unanticipated observation of this study is the apparent sensitivity of this sensor to high frequency electomagnetic signals associated with fault rupture and (or) rupture propagation, which may offer new insights into the physics of earthquake faulting.
| S-EPMC5750787 | biostudies-literature
Project description:Hydraulic stimulation to enhance energy extraction from geothermal and unconventional resources is typically accompanied by seismicity because injection changes pore pressures and temperatures, facilitating slippage of fractures and faults. Induced seismicity carries potential risk if events are large enough to damage infrastructure. The uncertainty invariably associated with the state of stress measurements and subsurface geomechanics parameters affects the analysis of fault slip and seismicity induced resulting from hydraulic fracturing. In this study, a probabilistic approach is used to assess the slip tendency of known faults crossing the compartmentalized Montney Formation of western Alberta and northeastern British Columbia. We first divide the formation into four different stress areas based on pore pressure deviations from hydrostatic. In each stress area, geomechanics parameters are expressed as probability distributions using multivariable datasets from borehole petrophysical data to injection-induced focal mechanisms. Monte Carlo simulations are applied to assess the potential slip tendency of local faults. We display the cumulative distribution function of critical pore pressure to cause slip on each fault by using analyses of the parameters of the Mohr-Coulomb shear failure criterion and local tectonic stress state. The results provide useful input for seismic hazard assessment and risk mitigation for local faults affected by high-rate fluid injection.
| S-EPMC9262911 | biostudies-literature
Project description:Fluid injection into rocks is increasingly used for energy extraction and for fluid wastes disposal, and can trigger/induce small- to medium-scale seismicity. Fluctuations in pore fluid pressure may also be associated with natural seismicity. The energy release in anthropogenically induced seismicity is sensitive to amount and pressure of fluid injected, through the way that seismic moment release is related to slipped area, and is strongly affected by the hydraulic conductance of the faulted rock mass. Bearing in mind the scaling issues that apply, fluid injection-driven fault motion can be studied on laboratory-sized samples. Here, we investigate both stable and unstable induced fault slip on pre-cut planar surfaces in Darley Dale and Pennant sandstones, with or without granular gouge. They display contrasting permeabilities, differing by a factor of 105, but mineralogies are broadly comparable. In permeable Darley Dale sandstone, fluid can access the fault plane through the rock matrix and the effective stress law is followed closely. Pore pressure change shifts the whole Mohr circle laterally. In tight Pennant sandstone, fluid only injects into the fault plane itself; stress state in the rock matrix is unaffected. Sudden access by overpressured fluid to the fault plane via hydrofracture causes seismogenic fault slips.This article is part of the themed issue 'Faulting, friction and weakening: from slow to fast motion'.
| S-EPMC5580445 | biostudies-literature
Project description:Slow earthquakes represent an important conundrum in earthquake physics. While regular earthquakes are catastrophic events with rupture velocities governed by elastic wave speed, the processes that underlie slow fault slip phenomena, including recent discoveries of tremor, slow-slip and low-frequency earthquakes, are less understood. Theoretical models and sparse laboratory observations have provided insights, but the physics of slow fault rupture remain enigmatic. Here we report on laboratory observations that illuminate the mechanics of slow-slip phenomena. We show that a spectrum of slow-slip behaviours arises near the threshold between stable and unstable failure, and is governed by frictional dynamics via the interplay of fault frictional properties, effective normal stress and the elastic stiffness of the surrounding material. This generalizable frictional mechanism may act in concert with other hypothesized processes that damp dynamic ruptures, and is consistent with the broad range of geologic environments where slow earthquakes are observed.
| S-EPMC4821871 | biostudies-other
Project description:Understanding the temporal evolution of foreshocks and their relation to earthquake nucleation is important for earthquake early warning systems, earthquake hazard assessment, and earthquake physics. Laboratory experiments on intact rock and rough fractures have demonstrated that the number and size of acoustic emission (AE) events increase and that the Gutenberg-Richter b-value decreases prior to coseismic failure. However, for lab fault zones of finite width, where shear occurs within gouge, the physical processes that dictate temporal variations in frequency-magnitude (F/M) statistics of lab foreshocks are unclear. Here, we report on a series of laboratory experiments to illuminate the physical processes that govern temporal variations in b-value and AE size. We record AE data continuously for hundreds of lab seismic cycles and report F/M statistics. Our foreshock catalogs include cases where F/M data are not exponentially distributed, but we retain the concept of b-value for comparison with other works. We find that b-value decreases as the fault approaches failure, consistent with previous works. We also find that b-value scales inversely with shear velocity and fault slip rate, suggesting that fault slip acceleration during earthquake nucleation could impact foreshock F/M statistics. We propose that fault zone dilation and grain mobilization have a strong influence on foreshock magnitude. Fault dilation at higher shearing rates increases porosity and results in larger foreshocks and smaller b-values. Our observations suggest that lab earthquakes are preceded by a preparatory nucleation phase with systematic variations in AE and fault zone properties.
| S-EPMC9286047 | biostudies-literature
Project description:Data-driven machine-learning for predicting instantaneous and future fault-slip in laboratory experiments has recently progressed markedly, primarily due to large training data sets. In Earth however, earthquake interevent times range from 10's-100's of years and geophysical data typically exist for only a portion of an earthquake cycle. Sparse data presents a serious challenge to training machine learning models for predicting fault slip in Earth. Here we describe a transfer learning approach using numerical simulations to train a convolutional encoder-decoder that predicts fault-slip behavior in laboratory experiments. The model learns a mapping between acoustic emission and fault friction histories from numerical simulations, and generalizes to produce accurate predictions of laboratory fault friction. Notably, the predictions improve by further training the model latent space using only a portion of data from a single laboratory earthquake-cycle. The transfer learning results elucidate the potential of using models trained on numerical simulations and fine-tuned with small geophysical data sets for potential applications to faults in Earth.
| S-EPMC8677738 | biostudies-literature
Project description:Tsunami generation from earthquake-induced seafloor deformations has long been recognized as a major hazard to coastal areas. Strike-slip faulting has generally been considered insufficient for triggering large tsunamis, except through the generation of submarine landslides. Herein, we demonstrate that ground motions due to strike-slip earthquakes can contribute to the generation of large tsunamis (>1 m), under rather generic conditions. To this end, we developed a computational framework that integrates models for earthquake rupture dynamics with models of tsunami generation and propagation. The three-dimensional time-dependent vertical and horizontal ground motions from spontaneous dynamic rupture models are used to drive boundary motions in the tsunami model. Our results suggest that supershear ruptures propagating along strike-slip faults, traversing narrow and shallow bays, are prime candidates for tsunami generation. We show that dynamic focusing and the large horizontal displacements, characteristic of strike-slip earthquakes on long faults, are critical drivers for the tsunami hazard. These findings point to intrinsic mechanisms for sizable tsunami generation by strike-slip faulting, which do not require complex seismic sources, landslides, or complicated bathymetry. Furthermore, our model identifies three distinct phases in the tsunamic motion, an instantaneous dynamic phase, a lagging coseismic phase, and a postseismic phase, each of which may affect coastal areas differently. We conclude that near-source tsunami hazards and risk from strike-slip faulting need to be re-evaluated.
| S-EPMC8126766 | biostudies-literature
Project description:An intraplate earthquake doublet, with 11-min delay between the events, devastated the city of Varzeghan in northwestern Iran on August 11, 2012. The first Mw 6.5 strike-slip earthquake, which occurred after more than 200 years of low seismicity, was followed by an Mw 6.4 oblique thrust event at an epicentral separation of about 6 km. While the first event can be associated with a distinct surface rupture, the absence of a surface fault trace and no clear aftershock signature makes it challenging to identify the fault plane of the second event. We use teleseismic body wave inversion to deduce the slip distribution in the first event. Using both P and SH waves stabilize the inversion and we further constrain the result with the surface rupture extent and the aftershock distribution. The obtained slip pattern shows two distinct slip patches with dissimilar slip directions where aftershocks avoid high-slip areas. Using the estimated slip for the first event, we calculate the induced Coulomb stress change on the nodal planes of the second event and find a preference for higher Coulomb stress on the N-S nodal plane. Assuming a simple slip model for the second event, we estimate the combined Coulomb stress changes from the two events on the focal planes of the largest aftershocks. We find that 90% of the aftershocks show increased Coulomb stress on one of their nodal planes when the N-S plane of the second event is assumed to be the correct fault plane.
| S-EPMC6015626 | biostudies-literature
Project description:A long-lasting question in earthquake physics is why slip on faults occurs as creep or dynamic rupture. We compute passive measurements of the seismic P wave velocity gradient across the San Andreas Fault near Parkfield, where this transition of slip mode occurs at a scale of a few kilometers. Unbiased measurements are obtained through the application of a new Bayesian local earthquake tomographic code that avoids the imposition of any user-defined, initial velocity-contrast across the fault, or any damping scheme that may cause biased amplitude in retrieved seismic velocities. We observe that across-fault velocity gradients correlate with the slip behavior of the fault. The P wave velocity contrast decays from 20% in the fault section that experience dynamic rupture to 4% in the creeping section, suggesting that rapid change of material properties and attitude to sustain supra-hydrostatic fluid pressure are conditions for development of dynamic rupture. Low Vp and high Vp/Vs suggest that fault rheology at shallow depth is conversely controlled by low frictional strength material.
| S-EPMC7374945 | biostudies-literature