Browse
Submit Data
Databases
API
Help

Dataset Information

16 Views

0 Connections

0 Citations

0 Reanalyses

0 Downloads

Omics score: 0

Stress dependence of indentation modulus for carbon fiber in polymer composite.

ABSTRACT: Elastic modulus measured through atomic force microscopy (AFM)-based indentation on single carbon fiber (CF) is found with dependence on lateral applied stress. An in situ indentation experiment inside a high-resolution transmission electron microscope was performed to quantitatively understand this phenomenon by observing microstructure change in the indented area. Change of graphitic basal plane misalignment angle during indentation was linked to a continuous change of modulus with the help of finite element simulation. The established relationship between modulus and indentation force was further used to calculate residual stress distribution in CF imbedded in a CF reinforced polymer composite using the AFM indentation technique. The stress-induced formation of nanoscale defects in the CF and their transformation into fracture were directly characterized.

SUBMITTER: Wang H

PROVIDER: S-EPMC6493271 | biostudies-literature |

REPOSITORIES: biostudies-literature

ACCESS DATA

Json Xml

Similar Datasets

Stress mapping reveals extrinsic toughening of brittle carbon fiber in polymer matrix.

Project description:We conducted an in situ study on CFRP fracturing process using atomic-force-microscopy-based stress-sensitive indentation. Tensile stress distribution during fracture initiation and propagation was directly observed quantitatively. It led to a discovery that previously believed catastrophic fracture of individual carbon fiber develops in a controllable manner in the polymer matrix, exhibiting 10 times increase of fracture toughness. Plastic deformation in crack-bridging polymer matrix was accounted for the toughening mechanism. The model was applied to explain low temperature strength weakening of CFRP bulk material when matrix plasticity was intentionally 'shut down' by cryogenic cooling.

| S-EPMC7269064 | biostudies-literature

Mitigation of Galvanic Corrosion in Bolted Joint of AZ31B and Carbon Fiber-Reinforced Composite Using Polymer Insulation.

Project description:The use of polymer insulation to mitigate galvanic corrosion was examined for bolted joints of AZ31B Mg alloy and carbon fiber-reinforced composite. To assess the corrosion behaviors of bolted joints with and without polymer insulation, solution immersion and salt spray exposure (ASTM B117) tests were conducted, and the corrosion depths and volumes were determined for the joint specimens after the tests. The polymer-insulated bolted joints exhibited much lower corrosion depths and volumes, highlighting the effective mitigation of galvanic corrosion. The reductions of joint strength in the post-corrosion joint specimens were relatively small (up to ~10%) in the polymer-insulated group but greater (up to 90%) in the group with no insulation. Cross-sectional characterization of post-corrosion joints with polymer insulation revealed local pits developed on AZ31B under galvanic influence, indicating that limited galvanic attack (that did not decrease the joining integrity significantly) could still occur during a long salt spray exposure (~1264 h) owing to the permeation of an aqueous corrosive medium.

| S-EPMC8036256 | biostudies-literature

Shape-morphing carbon fiber composite using electrochemical actuation.

Project description:Structures that are capable of changing shape can increase efficiency in many applications, but are often heavy and maintenance intensive. To reduce the mass and mechanical complexity solid-state morphing materials are desirable but are typically nonstructural and problematic to control. Here we present an electrically controlled solid-state morphing composite material that is lightweight and has a stiffness higher than aluminum. It is capable of producing large deformations and holding them with no additional power, albeit at low rates. The material is manufactured from commercial carbon fibers and a structural battery electrolyte, and uses lithium-ion insertion to produce shape changes at low voltages. A proof-of-concept material in a cantilever setup is used to show morphing, and analytical modeling shows good correlation with experimental observations. The concept presented shows considerable promise and paves the way for stiff, solid-state morphing materials.

| S-EPMC7149449 | biostudies-literature

Effects of gel thickness on microscopic indentation measurements of gel modulus.

Project description:In vitro, animal cells are mostly cultured on a gel substrate. It was recently shown that substrate stiffness affects cellular behaviors in a significant way, including adhesion, differentiation, and migration. Therefore, an accurate method is needed to characterize the modulus of the substrate. In situ microscopic measurements of the gel substrate modulus are based on Hertz contact mechanics, where Young's modulus is derived from the indentation force and displacement measurements. In Hertz theory, the substrate is modeled as a linear elastic half-space with an infinite depth, whereas in practice, the thickness of the substrate, h, can be comparable to the contact radius and other relevant dimensions such as the radius of the indenter or steel ball, R. As a result, measurements based on Hertz theory overestimate the Young's modulus. In this work, we discuss the limitations of Hertz theory and then modify it, taking into consideration the nonlinearity of the material and large deformation using a finite-element method. We present our results in a simple correction factor, ?, the ratio of the corrected Young's modulus and the Hertz modulus in the parameter regime of ?/h ? min (0.6, R/h) and 0.3 ?R/h ? 12.7. The ? factor depends on two dimensionless parameters, R/h and ?/h (where ? is the indentation depth), both of which are easily accessible to experiments. This correction factor agrees with experimental observations obtained with the use of polyacrylamide gel and a microsphere indentation method in the parameter range of 0.1 ??/h ? 0.4 and 0.3 ?R/h ? 6.2. The effect of adhesion on the use of Hertz theory for small indentation depth is also discussed.

| S-EPMC3145280 | biostudies-literature

Mesoporous Piezoelectric Polymer Composite Films with Tunable Mechanical Modulus for Harvesting Energy from Liquid Pressure Fluctuation.

Project description:Harvesting mechanical energy from biological systems possesses great potential for in vivo powering implantable electronic devices. In this paper, a development of flexible piezoelectric nanogenerator (NG) is reported based on mesoporous poly(vinylidene fluoride) (PVDF) films. Monolithic mesoporous PVDF is fabricated by a template-free sol-gel-based approach at room temperature. By filling the pores of PVDF network with poly(dimethylsiloxane) (PDMS) elastomer, the composite's modulus is effectively tuned over a wide range down to the same level of biological systems. A close match of the modulus between NG and the surrounding biological component is critical to achieve practical integration. Upon deformation, the composite NG exhibits appreciable piezoelectric output that is comparable to or higher than other PVDF-based NGs. An artificial artery system is fabricated using PDMS with the composite NG integrated inside. Effective energy harvesting from liquid pressure fluctuation (simulating blood pressure fluctuation) is successfully demonstrated. The simple and effective approach for fabricating mesoporous PVDF with tunable mechanical properties provides a promising route toward the development of self-powered implantable devices.

| S-EPMC5462116 | biostudies-literature

Experimental Investigation on the Creep Property of Carbon Fiber Reinforced Polymer Tendons under High Stress Levels.

Project description:Carbon fiber reinforced polymer (CFRP) tendons are generally used as prestressing members to take full advantage of their high strength. Their creep property is one of the key factors influencing the reliability and safety of the structures, especially under sustained high stress. In this study, using a new wedge-type anchorage system, experimental research was carried out on the creep behavior of CFRP tendons under high stress levels from 0.69 to 0.85 fu. All the tests lasted for a duration of 1000 h. It was found that the creep coefficient tends to increase with the stress level. Compared to their static properties, the residual strength of CFRP tendons after creep tests is 4.54% lower while the after-creep elastic modulus is 6.99% higher. Through data analysis, a semi-logarithm linear relationship between the creep coefficient and time was established, and the creep coefficients at 1 million hours were extrapolated.

| S-EPMC6266062 | biostudies-literature

Mussel-Inspired Design of a Carbon Fiber-Cellulosic Polymer Interface toward Engineered Biobased Carbon Fiber-Reinforced Composites.

Project description:Tuning interactions at the interfaces in carbon fiber (CF)-reinforced polymer composites necessitates the implementation of CF surface modification strategies that often require destructive environmentally unfriendly chemistries. In this study, interfacial interactions in cellulose-based composites are tailored by means of a mussel-inspired adhesive polydopamine (PDA) coating, being inherently benign for the environment and for the structure of CFs. The step-by-step growth of PDA was followed by increasing treatment time leading to a hydrophilic PDA-coated surface, presumably via surface-based polymerization mechanisms attributed to strong π-π stacking interactions. Although PDA deposition led to an initial increase in the interfacial shear strength (IFSS) (5 h), it decreased at a longer reaction time (24 h), the formation of weakly attached PDA particles on the coated surface can possibly lie behind the latter phenomenon. Nevertheless, the mechanical properties of the prepared short CF-reinforced composite were improved (tensile strength increased ∼12% compared to the unmodified surface) with decreasing IFSS owing to the particular morphological design, resulting in longer fiber segments. Our study underlines the importance of the morphological design at the interface and considers PDA as a promising bioinspired material to tailor interfacial interactions.

| S-EPMC7594004 | biostudies-literature

Surface Structured Polymer Blend Fibers and Their Application in Fiber Reinforced Composite.

Project description:Melt-spun surface structured fiber could be a large-scale versatile platform for materials with advanced surface function and local properties. Fibers with distinct surface and bulk structures are developed by tailoring the viscosity ratio and blend ratio of polymer component using the melt-spinning method. Spherical bulge and fibril groove structured fibers are obtained in different viscosity ratio and blend ratio systems. The interfacial bonding between fiber and matrix is improved due to the mechanical interlocking between the structured surface and matrix. The low-viscosity second phase stays as a spherical droplet even in high content. The second phase in matched- and high-viscosity ratio cases is deformed into fibril like droplet which causes an in-situ fibration of the second phase in polymer blend fiber with an enhanced mechanical property. This method provides a simple route to developing polymer materials with surface structure and appropriate mechanical properties to apply in textile and polymer fiber-reinforced composite materials.

| S-EPMC7579542 | biostudies-literature

Polymer Modified Carbon Fiber Microelectrodes for Precision Neurotransmitter Metabolite Measurements.

Project description:Carbon fiber-microelectrodes (CFMEs) are considered to be one of the standard electrodes for neurotransmitter detection such as dopamine (DA). DA is physiologically important for many pharmacological and behavioral states, but is readily metabolized on a fast, subsecond timescale. Recently, DA metabolites such as 3-methoxytyramine (3-MT) and 3,4-dihydroxyphenylacetaldehyde (DOPAL) were found to be involved in physiological functions, such as movement control and progressive neuro degeneration. However, there is no current assay to detect and differentiate them from DA. In this study, we demonstrate the co-detection of similarly structured neurochemicals such as DA, 3-MT, and DOPAL. We accomplished this through electrodepositing CFMEs with polyethyleneimine (PEI) and poly(3,4-ethylenedioxythiophene) polystyrene sulfonate (PEDOT:PSS) polymers. This endowed the bare unmodified CFMEs with surface charge, physical, and chemical differences, which resulted in the improved sensitivity and selectivity of neurotransmitter detection. The differentiation and detection of 3-MT, DOPAL, and DA will potentially help further understand the important physiological roles that these dopaminergic metabolites play in vivo.

| S-EPMC8081299 | biostudies-literature

Stretchable, weavable coiled carbon nanotube/MnO2/polymer fiber solid-state supercapacitors.

Project description:Fiber and yarn supercapacitors that are elastomerically deformable without performance loss are sought for such applications as power sources for wearable electronics, micro-devices, and implantable medical devices. Previously reported yarn and fiber supercapacitors are expensive to fabricate, difficult to upscale, or non-stretchable, which limits possible use. The elastomeric electrodes of the present solid-state supercapacitors are made by using giant inserted twist to coil a nylon sewing thread that is helically wrapped with a carbon nanotube sheet, and then electrochemically depositing pseudocapacitive MnO2 nanofibers. These solid-state supercapacitors decrease capacitance by less than 15% when reversibly stretched by 150% in the fiber direction, and largely retain capacitance while being cyclically stretched during charge and discharge. The maximum linear and areal capacitances (based on active materials) and areal energy storage and power densities (based on overall supercapacitor dimensions) are high (5.4 mF/cm, 40.9 mF/cm(2), 2.6 ?Wh/cm(2) and 66.9 ?W/cm(2), respectively), despite the engineered superelasticity of the fiber supercapacitor. Retention of supercapacitor performance during large strain (50%) elastic deformation is demonstrated for supercapacitors incorporated into the wristband of a glove.

| S-EPMC4369743 | biostudies-literature

OmicsDI is part of the ELIXIR infrastructure

OmicsDI is an Elixir interoperability service. Learn more ›

OmicsDI Databases

PRIDE
PeptideAtlas
MassIVE
JPOST Repository
Physiome Model Repository

EGA
EVA
ENA
LINCS
PAXDB
Cell Collective

MetaboLights
Metabolomics Workbench
MetabolomeExpress
GNPS
BioModels
FAIRDOMHub

ArrayExpress
dbGaP
ExpressionAtlas
GEO
NODE

Information

Databases
Help
API
Contact us
Code on GitHub
Terms of use
Submit Data