Browse
Submit Data
Databases
API
Help

Dataset Information

35 Views

0 Connections

0 Citations

0 Reanalyses

0 Downloads

Omics score: 0

A 3D-printed hand-powered centrifuge for molecular biology.

ABSTRACT: The centrifuge is an essential tool for many aspects of research and medical diagnostics. However, conventional centrifuges are often inaccessible outside of standard laboratory settings, such as remote field sites, because they require a constant external power source and can be prohibitively costly in resource-limited settings and Science, technology, engineering, and mathematics (STEM)-focused programs. Here we present the 3D-Fuge, a 3D-printed hand-powered centrifuge, as a novel alternative to standard benchtop centrifuges. Based on the design principles of a paper-based centrifuge, this 3D-printed instrument increases the volume capacity to 2 mL and can reach hand-powered centrifugation speeds up to 6,000 rpm. The 3D-Fuge devices presented here are capable of centrifugation of a wide variety of different solutions such as spinning down samples for biomarker applications and performing nucleotide extractions as part of a portable molecular lab setup. We introduce the design and proof-of-principle trials that demonstrate the utility of low-cost 3D-printed centrifuges for use in remote field biology and educational settings.

SUBMITTER: Byagathvalli G

PROVIDER: S-EPMC6528969 | biostudies-literature |

REPOSITORIES: biostudies-literature

ACCESS DATA

Json Xml

Similar Datasets

Hand-Powered Inertial Microfluidic Syringe-Tip Centrifuge.

Project description:Conventional sample preparation techniques require bulky and expensive instruments and are not compatible with next-generation point-of-care diagnostic testing. Here, we report a manually operated syringe-tip inertial microfluidic centrifuge (named i-centrifuge) for high-flow-rate (up to 16 mL/min) cell concentration and experimentally demonstrate its working mechanism and performance. Low-cost polymer films and double-sided tape were used through a rapid nonclean-room process of laser cutting and lamination bonding to construct the key components of the i-centrifuge, which consists of a syringe-tip flow stabilizer and a four-channel paralleled inertial microfluidic concentrator. The unstable liquid flow generated by the manual syringe was regulated and stabilized with the flow stabilizer to power inertial focusing in a four-channel paralleled concentrator. Finally, we successfully used our i-centrifuge for manually operated cell concentration. This i-centrifuge offers the advantages of low device cost, simple hand-powered operation, high-flow-rate processing, and portable device volume. Therefore, it holds potential as a low-cost, portable sample preparation tool for point-of-care diagnostic testing.

| S-EPMC8774109 | biostudies-literature

Design and Application of Portable Centrifuge Inspired by a Hand-Powered Spinning Top.

Project description:Traditional centrifuges, extensively employed in biology, chemistry, medicine, and other domains for tasks such as blood separation and pathogen extraction, have certain limitations. Their high cost, substantial size, and reliance on electricity restrict their range of application. Contemporary centrifuges, inspired by everyday items like paper trays and egg beaters, boast characteristics such as ease of operation, independence from electricity, and portability. These features offer unique advantages in specific situations, such as electricity shortages, inadequate infrastructure, and challenging medical conditions. Consequently, we designed a hand-powered portable centrifuge driven by pulling a rope. Our experiments revealed significant performance factors, including load capacity, rope length, and frequency of rope pulling. The results demonstrated that the revolutions per minute (RPM) of a hand-powered portable centrifuge were directly proportional to the length of the rope and the frequency of pulling, up to a certain limit, while inversely proportional to the load. When used for separating and washing polystyrene microspheres, the portable centrifuge's performance equaled that of traditional centrifuges. According to relevant calculations, this centrifuge could be capable of meeting the application of blood separation. Therefore, we believe this portable centrifuge will find meaningful applications in similar areas, particularly in resource-poor settings.

| S-EPMC10609382 | biostudies-literature

3D-printed supercapacitor-powered electrochemiluminescent protein immunoarray.

Project description:Herein we report a low cost, sensitive, supercapacitor-powered electrochemiluminescent (ECL) protein immunoarray fabricated by an inexpensive 3-dimensional (3D) printer. The immunosensor detects three cancer biomarker proteins in serum within 35 min. The 3D-printed device employs hand screen printed carbon sensors with gravity flow for sample/reagent delivery and washing. Prostate cancer biomarker proteins, prostate specific antigen (PSA), prostate specific membrane antigen (PSMA) and platelet factor-4 (PF-4) in serum were captured on the antibody-coated carbon sensors followed by delivery of detection-antibody-coated Ru(bpy)3(2+) (RuBPY)-doped silica nanoparticles in a sandwich immunoassay. ECL light was initiated from RuBPY in the silica nanoparticles by electrochemical oxidation with tripropylamine (TPrA) co-reactant using supercapacitor power and ECL was captured with a CCD camera. The supercapacitor was rapidly photo-recharged between assays using an inexpensive solar cell. Detection limits were 300-500f gmL(-1) for the 3 proteins in undiluted calf serum. Assays of 6 prostate cancer patient serum samples gave good correlation with conventional single protein ELISAs. This technology could provide sensitive onsite cancer diagnostic tests in resource-limited settings with the need for only moderate-level training.

| S-EPMC4673015 | biostudies-literature

All 3D Printed Stretchable Piezoelectric Nanogenerator for Self-Powered Sensor Application.

Project description:With the rapid development of wearable electronic systems, the need for stretchable nanogenerators becomes increasingly important for autonomous applications such as the Internet-of-Things. Piezoelectric nanogenerators are of interest for their ability to harvest mechanical energy from the environment with its inherent polarization arising from crystal structures or molecular arrangements of the piezoelectric materials. In this work, 3D printing is used to fabricate a stretchable piezoelectric nanogenerator which can serve as a self-powered sensor based on synthesized oxide-polymer composites.

| S-EPMC7728330 | biostudies-literature

Wirelessly Powered 3D Printed Hierarchical Biohybrid Robots with Multiscale Mechanical Properties.

Project description:The integration of flexible and stretchable electronics into biohybrid soft robotics can spur the development of new approaches to fabricate biohybrid soft machines, thus enabling a wide variety of innovative applications. Inspired by flexible and stretchable wireless-based bioelectronic devices, we have developed untethered biohybrid soft robots that can execute swimming motions, which are remotely controllable by the wireless transmission of electrical power into a cell simulator. To this end, wirelessly-powered, stretchable, and lightweight cell stimulators were designed to be integrated into muscle bodies without impeding the robots' underwater swimming abilities. The cell stimulators function by generating controlled monophasic pulses of up to ∼9 V in biological environments. By differentiating induced pluripotent stem cell-derived cardiomyocytes (iPSC-CMs) directly on the cell stimulators using an accordion-inspired, three-dimensional (3D) printing construct, we have replicated the native myofiber architecture with comparable robustness and enhanced contractibility. Wirelessly modulated electrical frequencies enabled us to control the speed and direction of the biohybrid soft robots. A maximum locomotion speed of ∼580 μm/s was achieved in robots possessing a large body size by adjusting the pacing frequency. This innovative approach will provide a platform for building untethered and biohybrid systems for various biomedical applications.

| S-EPMC9603592 | biostudies-literature

A low-cost and open-source mini benchtop centrifuge for molecular biology labs.

Project description:The aim of this manuscript is to provide all the necessary information to build a simple benchtop mini centrifuge that is able to remove droplets and liquid film from the inner wall of PCR tubes and PCR strips following vortexing. Users can choose between two rotors: one can hold up to six tubes (1.5/2 ml, or 500 µl and 200 µl tubes with adapters) or two PCR strips. The design consists of only three printed parts (optimized to be printed without supports) and cheap off-the-shelf components (80 mm computer fan, switches, food container and power supply). It can be assembled with basic soldering skills, no programming needed. While the total cost of materials is only 20 €, when compared to its commercial counterparts, this DIY benchtop spinner was equally capable to remove droplets. Comparing noise levels this model was quieter than an Eppendorf 5424, BioSan MSC-6000 or Kisker biotech centrifuges. Because it is designed to perform a very generic and common task, it could be useful for a very wide array of laboratories and researchers: molecular biology, genetics, microbiology, student labs, biohacking labs, etc.

| S-EPMC9234221 | biostudies-literature

Field Determination of Phosphate in Environmental Water by Using a Hand-Powered Paper Centrifuge for Preconcentration and Digital Image Colorimetric Sensing.

Project description:Phosphate concentration in natural water has been used as a water quality indicator, as it is one of the major nutrients for aquatic plants. However, the traditional phosphomolybdenum blue (PMB) method has limited sensitivity for visual or camera-based detection, leading to underestimation of the phosphate concentration. We present an ultralow-cost, rapid field preconcentration and digital image colorimetric sensing of low-concentration phosphate method for water analysis. A novel hand-powered paper centrifuge (paperfuge) is used for sample preparation and preconcentration. This paperfuge is made of two circular paper discs and a string. Six centrifuge tubes (CTs) originally used as glue dispensing tips with a sample capacity of ∼230 μL, are loaded on the paperfuge. After sampling, phosphate in the water sample is reacted to form PMB. Then, the reacted sample is drawn into a CT using an autopipette before the CT bottom is sealed by glue. After Oasis® HLB sorbents are added through the top of the CT, the CT top is also sealed with glue. The HLB sorbents adsorb PMB and are accumulated in the CT tip through centrifugation. The CT tips are cut and analyzed with the ImageJ software. It was found that the blue color intensity of sorbents is in a linear relationship to the phosphate concentration, with a linear range of 0-5 μM (r 2 = 0.9921) and limit of detection of 0.19 μM. In addition, this method has been applied to in-field water analysis. The results are in agreement with the standard PMB method.

| S-EPMC8786554 | biostudies-literature

3D-printed epifluidic electronic skin for machine learning-powered multimodal health surveillance.

Project description:The amalgamation of wearable technologies with physiochemical sensing capabilities promises to create powerful interpretive and predictive platforms for real-time health surveillance. However, the construction of such multimodal devices is difficult to be implemented wholly by traditional manufacturing techniques for at-home personalized applications. Here, we present a universal semisolid extrusion-based three-dimensional printing technology to fabricate an epifluidic elastic electronic skin (e3-skin) with high-performance multimodal physiochemical sensing capabilities. We demonstrate that the e3-skin can serve as a sustainable surveillance platform to capture the real-time physiological state of individuals during regular daily activities. We also show that by coupling the information collected from the e3-skin with machine learning, we were able to predict an individual's degree of behavior impairments (i.e., reaction time and inhibitory control) after alcohol consumption. The e3-skin paves the path for future autonomous manufacturing of customizable wearable systems that will enable widespread utility for regular health monitoring and clinical applications.

| S-EPMC10499321 | biostudies-literature

A 3D-printed molecular ferroelectric metamaterial.

Project description:Molecular ferroelectrics combine electromechanical coupling and electric polarizabilities, offering immense promise in stimuli-dependent metamaterials. Despite such promise, current physical realizations of mechanical metamaterials remain hindered by the lack of rapid-prototyping ferroelectric metamaterial structures. Here, we present a continuous rapid printing strategy for the volumetric deposition of water-soluble molecular ferroelectric metamaterials with precise spatial control in virtually any three-dimensional (3D) geometry by means of an electric-field-assisted additive manufacturing. We demonstrate a scaffold-supported ferroelectric crystalline lattice that enables self-healing and a reprogrammable stiffness for dynamic tuning of mechanical metamaterials with a long lifetime and sustainability. A molecular ferroelectric architecture with resonant inclusions then exhibits adaptive mitigation of incident vibroacoustic dynamic loads via an electrically tunable subwavelength-frequency band gap. The findings shown here pave the way for the versatile additive manufacturing of molecular ferroelectric metamaterials.

| S-EPMC7959491 | biostudies-literature

3D printed graphene-based self-powered strain sensors for smart tires in autonomous vehicles.

Project description:The transition of autonomous vehicles into fleets requires an advanced control system design that relies on continuous feedback from the tires. Smart tires enable continuous monitoring of dynamic parameters by combining strain sensing with traditional tire functions. Here, we provide breakthrough in this direction by demonstrating tire-integrated system that combines direct mask-less 3D printed strain gauges, flexible piezoelectric energy harvester for powering the sensors and secure wireless data transfer electronics, and machine learning for predictive data analysis. Ink of graphene based material was designed to directly print strain sensor for measuring tire-road interactions under varying driving speeds, normal load, and tire pressure. A secure wireless data transfer hardware powered by a piezoelectric patch is implemented to demonstrate self-powered sensing and wireless communication capability. Combined, this study significantly advances the design and fabrication of cost-effective smart tires by demonstrating practical self-powered wireless strain sensing capability.

| S-EPMC7588488 | biostudies-literature

OmicsDI is part of the ELIXIR infrastructure

OmicsDI is an Elixir interoperability service. Learn more ›

Tweets

OmicsDI Databases

PRIDE
PeptideAtlas
MassIVE
JPOST Repository
Physiome Model Repository

EGA
EVA
ENA
LINCS
PAXDB
Cell Collective

MetaboLights
Metabolomics Workbench
MetabolomeExpress
GNPS
BioModels
FAIRDOMHub

ArrayExpress
dbGaP
ExpressionAtlas
GEO
NODE

Information

Databases
Help
API
Contact us
Code on GitHub
Terms of use
Submit Data