Browse
Submit Data
Databases
API
Help

Dataset Information

10 Views

0 Connections

0 Citations

0 Reanalyses

0 Downloads

Omics score: 0

Sustainable Recycling of Insoluble Rust Waste for the Synthesis of Iron-Containing Perovskite-Type Catalysts.

ABSTRACT: Insoluble rust waste from the scraping of rusted iron-containing materials represents a cheap, eco-friendly, and available source of iron. LaFeO₃ perovskite-type powders were successfully prepared by solution combustion synthesis using rust waste from an electricity transmission tower manufacturer. Solution combustion synthesis enabled introduction of this insoluble iron precursor directly into the final product, bypassing complex extraction procedures. Catalytic activity in the propylene oxidation of the waste-derived LaFeO₃ with stoichiometric Fe/La ratio was almost identical to the commercial iron nitrate-derived LaFeO₃, thus demonstrating the viability of this recycling solution. The amount of waste iron precursor was varied and its effect on the powder properties was investigated. A lesser stoichiometric amount of precursor produced a LaFeO₃-La₂O₃ binary system, whereas a higher stoichiometric amount led to a LaFeO₃-Fe₂O₃ binary system. Catalytic activity of iron-rich compositions in the propylene oxidation was only slightly lower than the stoichiometric one, whereas iron-poor compositions were much less active. This eco-friendly methodology can be easily extended to other iron perovskites with different chemical compositions and to other iron-containing compounds.

SUBMITTER: Deganello F

PROVIDER: S-EPMC6647980 | biostudies-literature |

REPOSITORIES: biostudies-literature

ACCESS DATA

Json Xml

Similar Datasets

Recycling Waste Cotton Cloths for the Isolation of Cellulose Nanocrystals: A Sustainable Approach.

Project description:There is an interest in the sustainable utilization of waste cotton cloths because of their enormous volume of generation and high cellulose content. Waste cotton cloths generated are disposed of in a landfill, which causes environmental pollution and leads to the waste of useful resources. In the present study, cellulose nanocrystals (CNCs) were isolated from waste cotton cloths collected from a landfill. The waste cotton cloths collected from the landfill were sterilized and cleaned using supercritical CO2 (scCO2) technology. The cellulose was extracted from scCO2-treated waste cotton cloths using alkaline pulping and bleaching processes. Subsequently, the CNCs were isolated using the H2SO4 hydrolysis of cellulose. The isolated CNCs were analyzed to determine the morphological, chemical, thermal, and physical properties with various analytical methods, including attenuated total reflection-Fourier transform-infrared spectroscopy (ATR-FTIR), field-emission scanning electron microscopy (FE-SEM), energy-filtered transmission electron microscopy (EF-TEM), X-ray diffraction (XRD), thermogravimetric analysis (TGA), and differential scanning calorimetry (DSC). The results showed that the isolated CNCs had a needle-like structure with a length and diameter of 10-30 and 2-6 nm, respectively, and an aspect ratio of 5-15, respectively. Additionally, the isolated CNCs had a high crystallinity index with a good thermal stability. The findings of the present study revealed the potential of recycling waste cotton cloths to produce a value-added product.

| S-EPMC7922772 | biostudies-literature

Borate esters: Simple catalysts for the sustainable synthesis of complex amides.

Project description:Chemical reactions for the formation of amide bonds are among the most commonly used transformations in organic chemistry, yet they are often highly inefficient. A novel protocol for amidation using a simple borate ester catalyst is reported. The process presents significant improvements over other catalytic amidation methods in terms of efficiency and safety, with an unprecedented substrate scope including functionalized heterocycles and even unprotected amino acids. The method was used to access a wide range of functionalized amide derivatives, including pharmaceutically relevant targets, important synthetic intermediates, a catalyst, and a natural product.

| S-EPMC5609808 | biostudies-other

Co-transesterification of waste cooking oil, algal oil and dimethyl carbonate over sustainable nanoparticle catalysts.

Project description:Key challenges for the application of biodiesel include their high acid value, high viscosity, and low ester content. It is essential to develop later-generation biodiesel from unexploited non-food resources for a more sustainable future. Reuse of biowaste is critically important to address these issues of food safety and sustainability. Thus, the co-transesterification of waste cooking oil (WCO), algal oil (AO) and dimethyl carbonate (DMC) for the synthesis of fatty acid methyl esters (FAMEs) was investigated over a series of nanoparticle catalysts containing calcium, magnesium, potassium or nickel under mild reaction conditions. Nanoparticle catalyst samples were prepared from biowaste sources of chicken manure (CM), water hyacinth (WH) and algal bloom (AB), and characterized using XRD, Raman and FESEM techniques for the heterogeneous production of biodiesel. The catalyst was initially prepared by calcination at 850 °C for 4 h in a major presence of CaxMgyCO3, KCl and K2CO3. The WCO and AO co-conversion of 98% and FAMEs co-selectivity of 95% were obtained over CM nanoparticle catalyst under the reaction conditions of 80 °C, 20 mins and DMC to oil molar ratio of 6:1 with 3% catalyst loading and 3% methanol addition. Under the optimum condition, the density, viscosity, and cetane number of the biodiesel were in the range of diesel standards. Nanoparticle catalysts have been proven as a promising sustainable material in the catalytic transesterification of WCO and AO with the major presence of calcium, magnesium and potassium. This study highlights a sustainable approach via biowaste utilization for the enhancement of biodiesel quality with high ester content, low acid value, high cetane number, and low viscosity.

| S-EPMC7494454 | biostudies-literature

Unraveling iron oxides as abiotic catalysts of organic phosphorus recycling in soil and sediment matrices.

Project description:In biogeochemical phosphorus cycling, iron oxide minerals are acknowledged as strong adsorbents of inorganic and organic phosphorus. Dephosphorylation of organic phosphorus is attributed only to biological processes, but iron oxides could also catalyze this reaction. Evidence of this abiotic catalysis has relied on monitoring products in solution, thereby ignoring iron oxides as both catalysts and adsorbents. Here we apply high-resolution mass spectrometry and X-ray absorption spectroscopy to characterize dissolved and particulate phosphorus species, respectively. In soil and sediment samples reacted with ribonucleotides, we uncover the abiotic production of particulate inorganic phosphate associated specifically with iron oxides. Reactions of various organic phosphorus compounds with the different minerals identified in the environmental samples reveal up to ten-fold greater catalytic reactivities with iron oxides than with silicate and aluminosilicate minerals. Importantly, accounting for inorganic phosphate both in solution and mineral-bound, the dephosphorylarion rates of iron oxides were within reported enzymatic rates in soils. Our findings thus imply a missing abiotic axiom for organic phosphorus mineralization in phosphorus cycling.

| S-EPMC11258345 | biostudies-literature

Electrochemical recycling of homogeneous catalysts.

Project description:Homogeneous catalysts have rapid kinetics and keen reaction selectivity. However, their widespread use for industrial catalysis has remained limited because of challenges in reusability. Here, we propose a redox-mediated electrochemical approach for catalyst recycling using metallopolymer-functionalized electrodes for binding and release. The redox platform was investigated for the separation of key platinum and palladium homogeneous catalysts used in organic synthesis and industrial chemical manufacturing. Noble metal catalysts for hydrosilylation, silane etherification, Suzuki cross-coupling, and Wacker oxidation were recycled electrochemically. The redox electrodes demonstrated high sorption uptake for platinum-based catalysts (Qmax up to 200 milligrams of platinum per gram of adsorbent) from product mixtures, with up to 99.5% recovery, while retaining full catalytic activity over multiple cycles. The combination of mechanistic studies and electronic structure calculations indicate that selective interactions with anionic intermediates during the catalytic cycle played a key role in the separations. Last, continuous flow cell studies support the scalability and favorable technoeconomics of electrochemical recycling.

| S-EPMC9581474 | biostudies-literature

Sustainable synthesis of graphene sand composite from waste cooking oil for dye removal.

Project description:Waste cooking oil (WCO) appears to be a potential carbonaceous source for synthesizing graphene sand composite (GSC) adsorbent in removing pollutants. This study presents a green synthesis method of GSC using WCO as a sustainable carbon source for the synthesis of GSC through the thermal graphitization method. Characterization analysis conducted on GSCWCO verified the successful coating of WCO onto the sand surface and conversion to graphene, which possessed distinct functional groups and features of graphene materials. GSCWCO adsorbent effectiveness in removing Congo Red dye through batch adsorption was studied under the influence of different initial concentrations (20 to 100 mg/L), and the optimum pH (pH 2 to 10), contact time (5 to 240 min), and temperature (25 to 45 °C) were investigated. The GSCWCO showed removal rates of 91.5% achieved at an initial dye concentration of 20 mg L-1, 1.0 g of adsorbent dosage, a temperature of 25 °C, and 150 min of contact time. The GSCWCO exhibited a maximum capacity of 5.52 mg g-1, was well-fitted to the Freundlich isotherm model with an R2 value of 0.989 and had an adsorption mechanism that followed the pseudo-second-order kinetic model. Negative values of enthalpy (ΔH) and Gibbs free energy (ΔG) revealed that CR adsorption onto GSCWCO was a spontaneous and exothermic process. The presence of functional groups on the surface of GSCWCO with such interactions (π-π attractive forces, hydrophobic forces, and hydrogen bonding) was responsible for the anionic dye removal. Regeneration of GSCWCO adsorbent declined after four cycles, possibly due to the chemisorption of dyes with GSC that resulted in inefficient adsorption. Being a waste-to-wealth product, GSCWCO possessed great potential to be used for water treatment and simultaneously benefited the environment through the effort to reduce the excessive discharge of WCO.

| S-EPMC9894951 | biostudies-literature

Iron-catalysed synthesis and chemical recycling of telechelic 1,3-enchained oligocyclobutanes.

Project description:Closed-loop recycling offers the opportunity to mitigate plastic waste through reversible polymer construction and deconstruction. Although examples of chemical recycling of polymers are known, few have been applied to materials derived from abundant commodity olefinic monomers, which are the building blocks of ubiquitous plastic resins. Here we describe a [2+2] cycloaddition/oligomerization of 1,3-butadiene to yield a previously unrealized telechelic microstructure of (1,n'-divinyl)oligocyclobutane. This material is thermally stable, has stereoregular segments arising from chain-end control, and exhibits high crystallinity even at low molecular weight. Exposure of the oligocyclobutane to vacuum in the presence of the pyridine(diimine) iron precatalyst used to synthesize it resulted in deoligomerization to generate pristine butadiene, demonstrating a rare example of closed-loop chemical recycling of an oligomeric material derived from a commodity hydrocarbon feedstock.

| S-EPMC7875253 | biostudies-literature

Enzymatic lignocellulose hydrolysis: Improved cellulase productivity by insoluble solids recycling.

Project description:UnlabelledBackgroundIt is necessary to develop efficient methods to produce renewable fuels from lignocellulosic biomass. One of the main challenges to the industrialization of lignocellulose conversion processes is the large amount of cellulase enzymes used for the hydrolysis of cellulose. One method for decreasing the amount of enzyme used is to recycle the enzymes. In this study, the recycle of enzymes associated with the insoluble solid fraction after the enzymatic hydrolysis of cellulose was investigated for pretreated corn stover under a variety of recycling conditions.ResultsIt was found that a significant amount of cellulase activity could be recovered by recycling the insoluble biomass fraction, and the enzyme dosage could be decreased by 30% to achieve the same glucose yields under the most favorable conditions. Enzyme productivity (g glucose produced/g enzyme applied) increased between 30 and 50% by the recycling, depending on the reaction conditions. While increasing the amount of solids recycled increased process performance, the methods applicability was limited by its positive correlation with increasing total solids concentrations, reaction volumes, and lignin content of the insoluble residue. However, increasing amounts of lignin rich residue during the recycle did not negatively impact glucose yields.ConclusionsTo take advantage of this effect, the amount of solids recycled should be maximized, based on a given processes ability to deal with higher solids concentrations and volumes. Recycling of enzymes by recycling the insoluble solids fraction was thus shown to be an effective method to decrease enzyme usage, and research should be continued for its industrial application.

| S-EPMC3560254 | biostudies-literature

Roadmap to sustainable plastic waste management: a focused study on recycling PET for triboelectric nanogenerator production in Singapore and India.

Project description:This study explores the implications of plastic waste and recycling management on recyclates for manufacturing clean-energy harvesting devices. The focus is on a comparative analysis of using recycled polyethylene terephthalate (PET) for triboelectric nanogenerator (TENG) production, in two densely populated Asian countries of large economies, namely Singapore and India. Of the total 930,000 tonnes of plastic waste generated in Singapore in 2019, only 4% were recycled and the rest were incinerated. In comparison, India yielded 8.6 million tonnes of plastic waste and 70% were recycled. Both countries have strict recycling goals and have instituted different waste and recycling management regulations. The findings show that the waste policies and legislations, responsibilities and heterogeneity in collection systems and infrastructure of the respective country are the pivotal attributes to successful recycling. Challenges to recycle plastic include segregation, adulterants and macromolecular structure degradation which could influence the recyclate properties and pose challenges for manufacturing products. A model was developed to evaluate the economic value and mechanical potential of PET recyclate. The model predicted a 30% loss of material performance and a 65% loss of economic value after the first recycling cycle. The economic value depreciates to zero with decreasing mechanical performance of plastic after multiple recycling cycles. For understanding how TENG technology could be incorporated into the circular economy, a model has estimated about 20 million and 7300 billion pieces of aerogel mats can be manufactured from the PET bottles disposed in Singapore and India, respectively which were sufficient to produce small-scale TENG devices for all peoples in both countries.

| S-EPMC9125019 | biostudies-literature

Microwave-Mediated Synthesis of Lead-Free Cesium Titanium Bromide Double Perovskite: A Sustainable Approach.

Project description:Theoretical studies have identified cesium titanium bromide (Cs2TiBr6), a vacancy-ordered double perovskite, as a promising lead-free and earth-abundant candidate to replace Pb-based perovskites in photovoltaics. Our research is focused on overcoming the limitations associated with the current Cs2TiBr6 syntheses, which often involve high-vacuum and high-temperature evaporation techniques, high-energy milling, or intricate multistep solution processes conducted under an inert atmosphere, constraints that hinder industrial scalability. This study presents a straightforward, low-energy, and scalable solution procedure using microwave radiation to induce the formation of highly crystalline Cs2TiBr6 in a polar solvent. This methodology, where the choice of the solvent plays a crucial role, not only reduces the energy costs associated with perovskite production but also imparts exceptional stability to the resulting solid, in comparison with previous reports. This is a critical prerequisite for any technological advancement. The low-defective material demonstrates unprecedented structural stability under various stimuli such as moisture, oxygen, elevated temperatures (over 130 °C), and continuous exposure to white light illumination. In summary, our study represents an important step forward in the efficient and cost-effective synthesis of Cs2TiBr6, offering a compelling solution for the development of eco-friendly, earth-abundant Pb-free perovskite materials.

| S-EPMC10870712 | biostudies-literature

OmicsDI is part of the ELIXIR infrastructure

OmicsDI is an Elixir interoperability service. Learn more ›

Tweets

OmicsDI Databases

PRIDE
PeptideAtlas
MassIVE
JPOST Repository
Physiome Model Repository

EGA
EVA
ENA
LINCS
PAXDB
Cell Collective

MetaboLights
Metabolomics Workbench
MetabolomeExpress
GNPS
BioModels
FAIRDOMHub

ArrayExpress
dbGaP
ExpressionAtlas
GEO
NODE

Information

Databases
Help
API
Contact us
Code on GitHub
Terms of use
Submit Data