Browse
Submit Data
Databases
API
Help

Dataset Information

36 Views

0 Connections

0 Citations

0 Reanalyses

0 Downloads

Omics score: 0

Fabrication of sharp silicon hollow microneedles by deep-reactive ion etching towards minimally invasive diagnostics.

ABSTRACT: Microneedle technologies have the potential for expanding the capabilities of wearable health monitoring from physiology to biochemistry. This paper presents the fabrication of silicon hollow microneedles by a deep-reactive ion etching (DRIE) process, with the aim of exploring the feasibility of microneedle-based in-vivo monitoring of biomarkers in skin fluid. Such devices shall have the ability to allow the sensing elements to be integrated either within the needle borehole or on the backside of the device, relying on capillary filling of the borehole with dermal interstitial fluid (ISF) for transporting clinically relevant biomarkers to the sensor sites. The modified DRIE process was utilized for the anisotropic etching of circular holes with diameters as small as 30 μm to a depth of >300 μm by enhancing ion bombardment to efficiently remove the fluorocarbon passivation polymer. Afterward, isotropic wet and/or dry etching was utilized to sharpen the needle due to faster etching at the pillar top, achieving tip radii as small as 5 μm. Such sharp microneedles have been demonstrated to be sufficiently robust to penetrate porcine skin without needing any aids such as an impact-insertion applicator, with the needles remaining mechanically intact after repetitive penetrations. The capillary filling of DRIE-etched through-wafer holes with water has also been demonstrated, showing the feasibility of use to transport the analyte to the target sites.

SUBMITTER: Li Y

PROVIDER: S-EPMC6799813 | biostudies-literature |

REPOSITORIES: biostudies-literature

ACCESS DATA

Json Xml

Similar Datasets

Fabrication of sharp silicon arrays to wound Caenorhabditis elegans.

Project description:Understanding how animals respond to injury and how wounds heal remains a challenge. These questions can be addressed using genetically tractable animals, including the nematode Caenorhabditis elegans. Given its small size, the current methods for inflicting wounds in a controlled manner are demanding. To facilitate and accelerate the procedure, we fabricated regular arrays of pyramidal features ("pins") sharp enough to pierce the tough nematode cuticle. The pyramids were made from monocrystalline silicon wafers that were micro-structured using optical lithography and alkaline wet etching. The fabrication protocol and the geometry of the pins, determined by electron microscopy, are described in detail. We also used electron microscopy to characterize the different types of injury caused by these pins. Upon wounding, C. elegans expresses genes encoding antimicrobial peptides. A comparison of the induction of antimicrobial peptide gene expression using traditional needles and the pin arrays demonstrates the utility of this new method.

| S-EPMC7046703 | biostudies-literature

Reactive ion etching for fabrication of biofunctional titanium nanostructures.

Project description:One of the major problems with the bone implant surfaces after surgery is the competition of host and bacterial cells to adhere to the implant surfaces. To keep the implants safe against implant-associated infections, the implant surface may be decorated with bactericidal nanostructures. Therefore, fabrication of nanostructures on biomaterials is of growing interest. Here, we systematically studied the effects of different processing parameters of inductively coupled plasma reactive ion etching (ICP RIE) on the Ti nanostructures. The resultant Ti surfaces were characterized by using scanning electron microscopy and contact angle measurements. The specimens etched using different chamber pressures were chosen for measurement of the mechanical properties using nanoindentation. The etched surfaces revealed various morphologies, from flat porous structures to relatively rough surfaces consisting of nanopillars with diameters between 26.4?±?7.0 nm and 76.0?±?24.4 nm and lengths between 0.5?±?0.1 ?m and 5.2?±?0.3 ?m. The wettability of the surfaces widely varied in the entire range of hydrophilicity. The structures obtained at higher chamber pressure showed enhanced mechanical properties. The bactericidal behavior of selected surfaces was assessed against Staphylococcus aureus and Escherichia coli bacteria while their cytocompatibility was evaluated with murine preosteoblasts. The findings indicated the potential of such ICP RIE Ti structures to incorporate both bactericidal and osteogenic activity, and pointed out that optimization of the process conditions is essential to maximize these biofunctionalities.

| S-EPMC6906493 | biostudies-literature

Fabrication of porous silicon by metal-assisted etching using highly ordered gold nanoparticle arrays.

Project description:A simple method for the fabrication of porous silicon (Si) by metal-assisted etching was developed using gold nanoparticles as catalytic sites. The etching masks were prepared by spin-coating of colloidal gold nanoparticles onto Si. An appropriate functionalization of the gold nanoparticle surface prior to the deposition step enabled the formation of quasi-hexagonally ordered arrays by self-assembly which were translated into an array of pores by subsequent etching in HF solution containing H2O2. The quality of the pattern transfer depended on the chosen preparation conditions for the gold nanoparticle etching mask. The influence of the Si surface properties was investigated by using either hydrophilic or hydrophobic Si substrates resulting from piranha solution or HF treatment, respectively. The polymer-coated gold nanoparticles had to be thermally treated in order to provide a direct contact at the metal/Si interface which is required for the following metal-assisted etching. Plasma treatment as well as flame annealing was successfully applied. The best results were obtained for Si substrates which were flame annealed in order to remove the polymer matrix - independent of the substrate surface properties prior to spin-coating (hydrophilic or hydrophobic). The presented method opens up new resources for the fabrication of porous silicon by metal-assisted etching. Here, a vast variety of metal nanoparticles accessible by well-established wet-chemical synthesis can be employed for the fabrication of the etching masks.

| S-EPMC3463426 | biostudies-literature

Integration of sharp silicon nitride tips into high-speed SU8 cantilevers in a batch fabrication process.

Project description:Employing polymer cantilevers has shown to outperform using their silicon or silicon nitride analogues concerning the imaging speed of atomic force microscopy (AFM) in tapping mode (intermittent contact mode with amplitude modulation) by up to one order of magnitude. However, tips of the cantilever made out of a polymer material do not meet the requirements for tip sharpness and durability. Combining the high imaging bandwidth of polymer cantilevers with making sharp and wear-resistant tips is essential for a future adoption of polymer cantilevers in routine AFM use. In this work, we have developed a batch fabrication process to integrate silicon nitride tips with an average tip radius of 9 ± 2 nm into high-speed SU8 cantilevers. Key aspects of the process are the mechanical anchoring of a moulded silicon nitride tip and a two-step release process. The fabrication recipe can be adjusted to any photo-processable polymer cantilever.

| S-EPMC6902782 | biostudies-literature

Molecular Dynamics Simulation of Silicon Dioxide Etching by Hydrogen Fluoride Using the Reactive Force Field.

Project description:In this study, we develop a reactive force field (ReaxFF) for a Si/O/H/F system to perform etching simulations of SiO2 with an HF etchant. Quantum mechanical (QM) training sets from density functional theory calculations, which contain structures of reactant/product and energies with bond dissociation, valence angle distortions, and reactions between SiO2 clusters and SiO2 slab with HF gases, are used to optimize the ReaxFF parameters. Structures and energies calculated using the ReaxFF match well with the QM training sets. Using the optimized ReaxFF, we conduct molecular dynamics simulations of the etching process of SiO2 substrates with active HF molecules. The etching yield and number of reaction products with different incident energies of the HF etchant are investigated. These simulations show that the developed ReaxFF offers insights into the atomistic surface reaction of the SiO2 etching process.

| S-EPMC8223409 | biostudies-literature

Deep Etching of Silicon Based on Metal-Assisted Chemical Etching.

Project description:A deep etching method for silicon "micro"structures was successfully developed. This wet etching process is based on metal-assisted chemical etching (MACE), which was previously mainly utilized to etch the features that have lateral dimensions of "nanometers." In this novel MACE, the critical improvement was to promote the "out-of-plane" mass transfer at the metal/Si interface with an ultrathin metal film. This enabled us to etch micrometer-wide holes, which was previously challenging due to the mass transport limitation. In addition, it was found that when ethanol was used as a solvent instead of water, the formation of porous defects was suppressed. Under the optimized etch conditions, deep (>200 μm) and vertical (>88°) holes could be carved out at a fast etch rate (>0.4 μm/min). This novel deep MACE will find utility in applications such as microelectromechanical systems (MEMS) devices or biosensors.

| S-EPMC9118418 | biostudies-literature

Wafer-Scale Fabrication of Silicon Nanocones via Controlling Catalyst Evolution in All-Wet Metal-Assisted Chemical Etching.

Project description:All-wet metal-assisted chemical etching (MACE) is a simple and low-cost method to fabricate one-dimensional Si nanostructures. However, it remains a challenge to fabricate Si nanocones (SiNCs) with this method. Here, we achieved wafer-scale fabrication of SiNC arrays through an all-wet MACE process. The key to fabricate SiNCs is to control the catalyst evolution from deposition to etching stages. Different from conventional MACE processes, large-size Ag particles by solution deposition are obtained through increasing AgNO3 concentration or extending the reaction time in the seed solution. Then, the large-size Ag particles are simultaneously etched during the Si etching process in an etching solution with a high H2O2 concentration due to the accelerated cathode process and inhibited anode process in Ag/Si microscopic galvanic cells. The successive decrease of Ag particle sizes causes the proportionate increase of diameters of the etched Si nanostructures, forming SiNC arrays. The SiNC arrays exhibit a stronger light-trapping ability and better photoelectrochemical performance compared with Si nanowire arrays. SiNCs were fabricated by using n-type 1-10 Ω cm Si(100) wafers in this work. Though the specific experimental conditions for preparing SiNCs may differ when using different Si wafers, the summarized diagram will still provide valuable guidance for morphology control of Si nanostructures in MACE processes.

| S-EPMC8772306 | biostudies-literature

Fabrication of Solid State Nanopore in Thin Silicon Membrane Using Low Cost Multistep Chemical Etching.

Project description:Nanopore-based analysis is currently an area of great interest in many disciplines with the potential for exceptionally versatile applications in medicine. This work presents a novel step towards fabrication of a single solid-state nanopore (SSSN) in a thin silicon membrane. Silicon nanopores are realized using multistep processes on both sides of n-type silicon-on-insulator (SOI) <100> wafer with resistivity 1-4 Ω·cm. An electrochemical HF etch with low current density (0.47 mA/cm²) is employed to produce SSSN. Blue LED is considered to emit light in a narrow band region which facilitates the etching procedure in a unilateral direction. This helps in production of straight nanopores in n-type Si. Additionally, a variety of pore diameters are demonstrated using different HF concentrations. Atomic force microscopy is used to demonstrate the surface morphology of the fabricated pores in non-contact mode. Pore edges exhibit a pronounced rounded shape and can offer high stability to fluidic artificial lipid bilayer to study membrane proteins. Electrochemically-fabricated SSSN has excellent smoothness and potential applications in diagnostics and pharmaceutical research on transmembrane proteins and label free detection.

| S-EPMC5458877 | biostudies-other

Versatilely tuned vertical silicon nanowire arrays by cryogenic reactive ion etching as a lithium-ion battery anode.

Project description:Production of high-aspect-ratio silicon (Si) nanowire-based anode for lithium ion batteries is challenging particularly in terms of controlling wire property and geometry to improve the battery performance. This report demonstrates tunable optimization of inductively coupled plasma reactive ion etching (ICP-RIE) at cryogenic temperature to fabricate vertically-aligned silicon nanowire array anodes with high verticality, controllable morphology, and good homogeneity. Three different materials [i.e., photoresist, chromium (Cr), and silicon dioxide (SiO2)] were employed as masks during the subsequent photolithography and cryogenic ICP-RIE processes to investigate their effects on the resulting nanowire structures. Silicon nanowire arrays with a high aspect ratio of up to 22 can be achieved by tuning several etching parameters [i.e., temperature, oxygen/sulfur hexafluoride (O2/SF6) gas mixture ratio, chamber pressure, plasma density, and ion energy]. Higher compressive stress was revealed for longer Si wires by means of Raman spectroscopy. Moreover, an anisotropy of lattice stress was found at the top and sidewall of Si nanowire, indicating compressive and tensile stresses, respectively. From electrochemical characterization, half-cell battery integrating ICP-RIE-based silicon nanowire anode exhibits a capacity of 0.25 mAh cm-2 with 16.67% capacity fading until 20 cycles, which has to be improved for application in future energy storage devices.

| S-EPMC8492725 | biostudies-literature

Hydrothermal etching fabrication of TiO2@graphene hollow structures: mutually independent exposed {001} and {101} facets nanocrystals and its synergistic photocaltalytic effects.

Project description:Highly exposed facets TiO2 attracts enormous attention due to its excellent separation effect of photogenerated electron-hole pairs and induced high performance of photocatalytic activity. Herein, a novel hydrothermal etching reaction was used to synthesize graphene-wrapped TiO2 hollow core-shell structures. Different with the reported co-exposed facets TiO2 single crystal nanoparticles, the present TiO2 core layer is composed by the mutually independent exposed {001} and {101} facets nanocrystals. Combined with the reduced graphene oxide shell layer, this graphene-wrapped TiO2 hollow core-shell structures formed a Z-scheme photocatalytic system, which possess simultaneously the high charge-separation efficiency and strong redox ability. Additionally, the as-prepared samples show a higher absorption property for organic molecules and visible light due to the presence of graphene. All of these unique properties ensure the excellent photocatalytic activity for the graphene-wrapped TiO2 hollow structures in the synergistic photo-oxidation of organic molecules and photo-reduced of Cr(VI) process. The TiO2 core composed with mutually independent exposed {001} and {101} facets nanocrystals is propose to play an important role in the fabrication of this Z-scheme photocatalytic system. Fabrication of Z-scheme photocatalytic system based on this unique exposed facets TiO2 nanocrystals will provides a new insight into the design and fabrication of advanced photocatalytic materials.

| S-EPMC5028751 | biostudies-literature

OmicsDI is part of the ELIXIR infrastructure

OmicsDI is an Elixir interoperability service. Learn more ›

Tweets

OmicsDI Databases

PRIDE
PeptideAtlas
MassIVE
JPOST Repository
Physiome Model Repository

EGA
EVA
ENA
LINCS
PAXDB
Cell Collective

MetaboLights
Metabolomics Workbench
MetabolomeExpress
GNPS
BioModels
FAIRDOMHub

ArrayExpress
dbGaP
ExpressionAtlas
GEO
NODE

Information

Databases
Help
API
Contact us
Code on GitHub
Terms of use
Submit Data