Unknown

Dataset Information

0

Influence of the Calcination Technique of Silica on the Properties and Performance of Ni/SiO2 Catalysts for Synthesis of Hydrogen via Methane Cracking Reaction.


ABSTRACT: Deactivation of catalysts due to rapid blocking of active surfaces and pores is a major problem for methane cracking. The removal of the template using different calcination methods contributes to the different characteristics of catalyst support. Therefore, silica supports were prepared with the sol-gel method, where sodium silicate and chitosan are a silica source and a template, respectively. Calcination using a microwave muffle furnace (MWF) was preferred over the conventional electric muffle furnace at the heating rates of 2 and 17 °C/min (CEF2 and CEF17, respectively) in order to remove the chitosan template. A nickel nitrate precursor was loaded onto the obtained silica supports by the incipient wetness impregnation method. The properties of the silica support and the Ni/SiO2 catalysts were characterized by means of N2-sorption, X-ray diffraction, scanning electron microscopy-energy-dispersive X-ray, field emission transmission electron microscopy, and H2 temperature-programmed reduction. The catalytic activity was evaluated using a fixed-bed reactor at 550 °C with a CH4/N2 ratio of 1:4 in the feed. The amount and the allotropes of carbon deposited on the spent catalysts were investigated using thermogravimetric/differential thermal analysis. The results showed that the SiO2-MWF support had a higher surface area and a larger pore volume of a mesoporous structure with larger interparticle channels than that of the SiO2-CEF supports. This leads to the higher dispersion of Ni metal particles over and inside the interparticle channels of the SiO2-MWF support. This provided a higher metal-support interaction, resulting in lower rates of methane conversion and carbon deposition on the catalyst surface than those of Ni/SiO2-CEF catalysts. However, it displayed a lower bed pressure. It was found that the carbon fibers deposited on all the catalysts were multiwalled carbon nanotubes (MWCNTs). Additionally, the base-growth mechanism of MWCNTs was only exhibited by the Ni/SiO2-MWF catalyst.

SUBMITTER: Panchan N 

PROVIDER: S-EPMC6843719 | biostudies-literature | 2019 Nov

REPOSITORIES: biostudies-literature

altmetric image

Publications

Influence of the Calcination Technique of Silica on the Properties and Performance of Ni/SiO<sub>2</sub> Catalysts for Synthesis of Hydrogen via Methane Cracking Reaction.

Panchan Noppadol N   Donphai Waleeporn W   Junsomboon Jaroon J   Niamnuy Chalida C   Chareonpanich Metta M  

ACS omega 20191025 19


Deactivation of catalysts due to rapid blocking of active surfaces and pores is a major problem for methane cracking. The removal of the template using different calcination methods contributes to the different characteristics of catalyst support. Therefore, silica supports were prepared with the sol-gel method, where sodium silicate and chitosan are a silica source and a template, respectively. Calcination using a microwave muffle furnace (MWF) was preferred over the conventional electric muffl  ...[more]

Similar Datasets

| S-EPMC10286284 | biostudies-literature
| S-EPMC6981678 | biostudies-literature
| S-EPMC6448361 | biostudies-literature
| S-EPMC4501498 | biostudies-literature
| S-EPMC8411779 | biostudies-literature
| S-EPMC7201101 | biostudies-literature
| S-EPMC8153405 | biostudies-literature
| S-EPMC6003342 | biostudies-literature
| S-EPMC10491930 | biostudies-literature
| S-EPMC7923007 | biostudies-literature