Browse
Submit Data
Databases
API
Help

Dataset Information

31 Views

0 Connections

0 Citations

0 Reanalyses

0 Downloads

Omics score: 0

Transformation Pathway upon Heating of Metastable ? Titanium Alloy Ti-15Mo Investigated by Neutron Diffraction.

ABSTRACT: A transformation pathway during thermal treatment of metastable ? Ti-15Mo alloy was investigated by in situ neutron diffraction. The evolution of individual phases ? , ? , and ? was investigated during linear heating with two heating rates of 1.9 ? C / min and 5 ? C / min and during aging at 450 ? C . The results showed that with a sufficient heating rate (5 ? C / min in this case), the ? phase dissolves before the ? phase forms. On the other hand, for the slower heating rate of 1.9 ? C / min , a small temperature interval of the coexistence of the ? and ? phases was detected. Volume fractions and lattice parameters of all phases were also determined.

SUBMITTER: Zhanal P

PROVIDER: S-EPMC6862573 | biostudies-literature | 2019 Oct

REPOSITORIES: biostudies-literature

ACCESS DATA

Json Xml

Publications

Transformation Pathway upon Heating of Metastable <i>β</i> Titanium Alloy Ti-15Mo Investigated by Neutron Diffraction.

Zháňal Pavel P Harcuba Petr P Stráský Josef J Šmilauerová Jana J Beran Přemysl P Hansen Thomas C TC Seiner Hanuš H Janeček Miloš M

Materials (Basel, Switzerland) 20191031 21

A transformation pathway during thermal treatment of metastable β Ti-15Mo alloy was investigated by in situ neutron diffraction. The evolution of individual phases α , β , and ω was investigated during linear heating with two heating rates of 1.9 ∘ C / min and 5 ∘ C / min and during aging at 450 ∘ C . The results showed that with a sufficient heating rate (5 ∘ C / min in this case), the ω phase dissolves before the α phase forms. On the other hand, for the slower heating rate of 1.9 ∘ C / min , ...[more]

PMID: 31683515

Similar Datasets

Deformation Induced Hierarchical Twinning Coupled with Omega Transformation in a Metastable ?-Ti Alloy.

Project description:Hierarchical twinning, at multiple length scales, was noted in a metastable body-centered cubic (bcc) ?-titanium alloy on tensile deformation. Site-specific characterization within the deformation bands, carried out using EBSD and TEM, revealed {332} <113> type primary bcc twins, containing different variants of secondary and tertiary twins, as well as the formation of stress-induced martensite (?"). Within the primary {332} <113> type twin, "destruction" of the prior quenched-in athermal ? phase was observed, while a stress-induced ? phase reforms within the tertiary twins, revealing the intricate nature of coupling between deformation twinning and displacive ? transformation.

| S-EPMC6362253 | biostudies-literature

Optimization of Low-Cost Ti-35421 Titanium Alloy: Phase Transformation, Bimodal Microstructure, and Combinatorial Mechanical Properties.

Project description:A sophisticated understanding of phase transformations and microstructure evolution is crucial in mechanical property optimization for the newly developed low-cost Ti-35421 (Ti-3Al-5Mo-4Cr-2Zr-1Fe wt.%) titanium alloy. The phase transformations in dual-phase Ti-35421 were studied by experiments and thermo-kinetic modeling. The phase transformation reactions and temperature ranges were determined as ???lamellar [410-660 °C], ?lamellar?? [660-740 °C], ?lath?? [740-825 °C]. The Gibbs-Thomson effect and multicomponent diffusivities were proven to be responsible for the distinguishing behaviors of growth and dissolution between two ? phases. The aging temperature of 540 °C was optimized based on calculations. It introduced a bimodal microstructure containing stubby ? lamellae and ? matrix. The mechanical properties of bimodal Ti-35421 were tested and compared with baseline alloy Ti-B19 and other near-? titanium alloys. The 540 °C aged alloy exhibits an optimal combination of mechanical properties with tensile strength of 1313 MPa, yield strength of 1240 MPa, elongation of 8.62%, and fracture toughness of 75.8 MPa·m1/2. The bimodal Ti-35421 shows comparable performance to Ti-B19 but has lower cost in raw materials and processing. The results also demonstrate that thermo-kinetic modeling can effectively be utilized in tailoring microstructure and enhancing mechanical properties.

| S-EPMC6747788 | biostudies-literature

Trifunctional nanoprecipitates ductilize and toughen a strong laminated metastable titanium alloy.

Project description:Metastability-engineering, e.g., transformation-induced plasticity (TRIP), can enhance the ductility of alloys, however it often comes at the expense of relatively low yield strength. Here, using a metastable Ti-1Al-8.5Mo-2.8Cr-2.7Zr (wt.%) alloy as a model material, we fabricate a heterogeneous laminated structure decorated by multiple-morphological α-nanoprecipitates. The hard α nanoprecipitate in our alloy acts not only as a strengthener to the material, but also as a local stress raiser to activate TRIP in the soft matrix for great uniform elongation and as a promoter to trigger interfacial delamination toughening for superior fracture resistance. By elaborately manipulating the activation sequence of lamellar-thickness-dependent deformation mechanisms in Ti-1Al-8.5Mo-2.8Cr-2.7Zr alloys, the yield strength of the present submicron-laminated alloy is twice that of equiaxed-coarse grained alloys with the same composition, yet without sacrificing the large uniform elongation. The desired mechanical properties enabled by this strategy combining the laminated metastable structure and trifunctional nanoprecipitates provide new insights into designing ultra-strong and ductile materials with great toughness.

| S-EPMC10011607 | biostudies-literature

Using transmission Kikuchi diffraction to characterise ? variants in an ?+? titanium alloy.

Project description:Two phase titanium alloys are important for high-performance engineering components, such as aeroengine discs. The microstructures of these alloys are tailored during thermomechanical processing to precisely control phase fractions, morphology and crystallographic orientations. In bimodal two phase (? + ?) Ti-6Al-2Sn-4Zr-2Mo (Ti-6242) alloys there are often three microstructural lengthscales to consider: large (?10 ?m) equiaxed primary ?; >200 nm thick plate ? with a basketweave morphology; and very fine scaled (<50 nm plate thickness) secondary ? that grows between the larger ? plates surrounded by retained ?. In this work, we utilise high spatial resolution transmission Kikuchi diffraction (TKD, also known as transmission-based electron backscatter diffraction, t-EBSD) and scanning electron microscopy (SEM)-based forward scattering electron imaging to resolve the structures and orientations of basketweave and secondary ? in Ti-6242. We analyse the ? variants formed within one prior ? grain, and test whether existing theories of habit planes of the phase transformation are upheld. Our analysis is important in understanding both the thermomechanical processing strategy of new bimodal two-phase titanium alloys, as well as the ultimate performance of these alloys in complex loading regimes such as dwell fatigue. Our paper champions the significant increase in spatial resolution afforded using transmission techniques, combined with the ease of SEM-based analysis using conventional electron backscatter diffraction (EBSD) systems and forescatter detector (FSD) imaging, to study the nanostructure of real-world engineering alloys.

| S-EPMC6849626 | biostudies-literature

Precipitation of string-shaped morphologies consisting of aligned ? phase in a metastable ? titanium alloy.

Project description:String-shaped morphologies consisting of preferentially aligned lath-shaped ? precipitates were observed in the metastable ? Ti-6Cr-5Mo-5V-4Al alloy after deformations at high strain rates and elevated temperatures. The morphology and 3-dimentional arrangement of this feature have been elaborated based on the characterizations via a combination of transmission electron microscopy, transmission kikuchi diffraction and atom probe tomography. The 2D projected morphology of the coalescent ? laths observed in the etched samples by SEM depends on the metallographic section. All the microstructural observations indicate that dislocation structures are most likely the nucleation sites for the aligned ? laths. In addition, an appropriate testing temperature, which can ensure a relatively high diffusion rate of solutes without inducing strong recovery of dislocation structures, is necessary for the occurrence of the string-shaped morphologies.

| S-EPMC5794777 | biostudies-literature

Correlating work hardening with co-activation of stacking fault strengthening and transformation in a high entropy alloy using in-situ neutron diffraction.

Project description:Transformation induced plasticity (TRIP) leads to enhancements in ductility in low stacking fault energy (SFE) alloys, however to achieve an unconventional increase in strength simultaneously, there must be barriers to dislocation motion. While stacking faults (SFs) contribute to strengthening by impeding dislocation motion, the contribution of SF strengthening to work hardening during deformation is not well understood; as compared to dislocation slip, twinning induced plasticity (TWIP) and TRIP. Thus, we used in-situ neutron diffraction to correlate SF strengthening to work hardening behavior in a low SFE Fe40Mn20Cr15Co20Si5 (at%) high entropy alloy, SFE ~ 6.31 mJ m-2. Cooperative activation of multiple mechanisms was indicated by increases in SF strengthening and γ-f.c.c. → ε-h.c.p. transformation leading to a simultaneous increase in strength and ductility. The present study demonstrates the application of in-situ, neutron or X-ray, diffraction techniques to correlating SF strengthening to work hardening.

| S-EPMC7747568 | biostudies-literature

Synergetic strengthening of layered steel sheet investigated using an in situ neutron diffraction tensile test.

Project description:Synergetic strengthening induced by plastic strain incompatibility at the interface, and the resulting extra geometrically necessary dislocations (GNDs) generated during plastic deformation, were investigated to understand the origin of extra strength in heterogeneous structured (HS) materials. The mechanism of extra GND generation in twinning-induced plasticity (TWIP)-interstitial free (IF) steel layered sheet was quantitatively analyzed by conducting in situ neutron scattering tensile test. Load partitioning due to the different mechanical properties between the TWIP-steel core and IF-steel sheath at the TWIP/IF interface was observed during the in situ tensile testing. Because of the plastic strain incompatibility from load partitioning, extra GNDs are generated and saturate during tensile deformation. The extra GNDs can be correlated with the back-stress evolution of the HS materials, which contributes to the strength of layered materials. Because of the back-stress evolution caused by load partitioning, the strength of TWIP-IF layered steel is higher than the strength estimated by the rule-of-mixtures. This finding offers a mechanism by which extra GNDs are generated during load partitioning and shows how they contribute to the mechanical properties of HS materials.

| S-EPMC6497632 | biostudies-literature

Is titanium alloy Ti-6Al-4 V cytotoxic to gingival fibroblasts-A systematic review.

Project description:ObjectivesGrade V titanium alloy (Ti-6Al-4 V) is a well-recognized metallic biomaterial for medical implants. There has been some controversy regarding the use of this alloy in medical devices in relation to the toxicity of vanadium. In Dentistry, Ti-6Al-4 V remains prevalent. This systematic review aims to evaluate the effects of Ti-6Al-4 V on cells relevant to oral environments such as gingival fibroblasts.Materials and methodsA literature search was undertaken for relevant English language publications in the following databases: Dental and Oral Science, Medline and Web of Science. The electronic search was supplemented with a search of references.ResultsAfter application of inclusion and exclusion criteria. A total of eight papers are included in this review. These papers were all in vitro studies and were categorized into whole implant, discs, or implant particles based on the type of test materials used in the studies.ConclusionBased on the analyses of the eight included studies in this review, if Ti-6Al-4 V as a material is unchallenged, i.e., as a whole implant in pH neutral environments, there appears to be little effect on fibroblasts. If Ti-6Al-4 V is challenged through corrosion or wear (particle release), the subsequent release of vanadium and aluminium particles has an increased cytotoxic effect in vitro in comparison to commercially pure titanium, hence concerns should be raised in the clinical setting.

| S-EPMC8638288 | biostudies-literature

Design and fabrication of a metastable β-type titanium alloy with ultralow elastic modulus and high strength.

Project description:Titanium and its alloys have become the most attractive implant materials due to their high corrosion resistance, excellent biocompatibility and relatively low elastic modulus. However, the current Ti materials used for implant applications exhibit much higher Young's modulus (50 ~ 120 GPa) than human bone (~30 GPa). This large mismatch in the elastic modulus between implant and human bone can lead to so-called "stress shielding effect" and eventual implant failure. Therefore, the development of β-type Ti alloys with modulus comparable to that of human bone has become an ever more pressing subject in the area of advanced biomedical materials. In this study, an attempt was made to produce a bone-compatible metastable β-type Ti alloy. By alloying and thermo-mechanical treatment, a metastable β-type Ti-33Nb-4Sn (wt. %) alloy with ultralow Young's modulus (36 GPa, versus ~30 GPa for human bone) and high ultimate strength (853 MPa) was fabricated. We believe that this method can be applied to developing advanced metastable β-type titanium alloys for implant applications. Also, this approach can shed light on design and development of novel β-type titanium alloys with large elastic limit due to their high strength and low elastic modulus.

| S-EPMC4592961 | biostudies-literature

Segregation mediated heterogeneous structure in a metastable β titanium alloy with a superior combination of strength and ductility.

Project description:In β titanium alloys, the β stabilizers segregate easily and considerable effort has been devoted to alleviate/eliminate the segregation. In this work, instead of addressing the segregation problems, the segregation was utilized to develop a novel microstructure consisting of a nanometre-grained duplex (α+β) structure and micrometre scale β phase with superior mechanical properties. An as-cast Ti-9Mo-6W alloy exhibited segregation of Mo and W at the tens of micrometre scale. This was subjected to cold rolling and flash annealing at 820 oC for 2 and 5 mins. The solidification segregation of Mo and W leads to a locally different microstructure after cold rolling (i.e., nanostructured β phase in the regions rich in Mo and W and plate-like martensite and β phase in regions relatively poor in Mo and W), which play a decisive role in the formation of the heterogeneous microstructure. Tensile tests showed that this alloy exhibited a superior combination of high yield strength (692 MPa), high tensile strength (1115 MPa), high work hardening rate and large uniform elongation (33.5%). More importantly, the new technique proposed in this work could be potentially applicable to other alloy systems with segregation problems.

| S-EPMC5951864 | biostudies-literature

OmicsDI is part of the ELIXIR infrastructure

OmicsDI is an Elixir interoperability service. Learn more ›

Tweets

OmicsDI Databases

PRIDE
PeptideAtlas
MassIVE
JPOST Repository
Physiome Model Repository

EGA
EVA
ENA
LINCS
PAXDB
Cell Collective

MetaboLights
Metabolomics Workbench
MetabolomeExpress
GNPS
BioModels
FAIRDOMHub

ArrayExpress
dbGaP
ExpressionAtlas
GEO
NODE

Information

Databases
Help
API
Contact us
Code on GitHub
Terms of use
Submit Data