Field-induced p-n transition in yttria-stabilized zirconia.
Ontology highlight
ABSTRACT:
SUBMITTER: Jovani M
PROVIDER: S-EPMC6898179 | biostudies-literature | 2019 Dec
REPOSITORIES: biostudies-literature
Publications
Field-induced p-n transition in yttria-stabilized zirconia.
Jovaní Marc M Beltrán-Mir Héctor H Cordoncillo Eloísa E West Anthony R AR
Scientific reports 20191206 1
Oxide ion conducting yttria-stabilised zirconia ceramics show the onset of electronic conduction under a small bias voltage. Compositions with a high yttria content undergo a transition from p-type to n-type behavior at voltages in the range 2.4 to 10 V, which also depends on oxygen partial pressure. Surface reactions have a direct influence on bulk electronic conductivities, with possible implications for voltage-induced flash phenomena and resistive switching. ...[more]
Similar Datasets
Project description:In this work, a set of density-functional tight-binding (DFTB) parameters for the Zr-Zr, Zr-O, Y-Y, Y-O, and Zr-Y interactions was developed for bulk and surface simulations of ZrO2 (zirconia), Y2O3 (yttria), and yttria-stabilized zirconia (YSZ) materials. The parameterization lays the ground work for realistic simulations of zirconia-, yttria-, and YSZ-based electrolytes in solid oxide fuel cells and YSZ-based catalysts on long timescales and relevant size scales. The parameterization was validated for the zirconia and yttria polymorphs observed under standard conditions based on density functional theory calculations and experimental data. Additionally, we performed DFTB-based molecular dynamics (MD) simulations to compute structural and vibrational properties of these materials. The results show that the parameters can give a qualitatively correct phase ordering of zirconia, where the tetragonal phase is more stable than the cubic phase at a lower temperature. The lattice parameters are only slightly overestimated by 0.05-0.1 Å (2% error), still within the typical accuracy of first-principles methods. Additionally, the MD results confirm that zirconia and yttria phases are stable against transformations under standard conditions. The parameterization also predicts that vibrational spectra are within the range of 100-1000 cm-1 for zirconia and 100-800 cm-1 for yttria, which is in good agreement with predictions both from full quantum mechanics and a recently developed classical force field. To further demonstrate the advantage of the developed DFTB parameters in terms of computational resources, we conducted DFTB/MD simulations of the YSZ4 and YS12 models containing approximately 750 atoms.
| S-EPMC8359130 | biostudies-literature
Project description:Repeated non-diffuse optical imaging of the brain is difficult. This is due to the fact that the cranial bone is highly scattering and thus a strong optical barrier. Repeated craniotomies increase the risk of complications and may disrupt the biological systems being imaged. We previously introduced a potential solution in the form of a transparent ceramic cranial implant called the Window to the Brain (WttB) implant. This implant is made of nanocrystalline Yttria-Stabilized Zirconia (nc-YSZ), which possesses the requisite mechanical strength to serve as a permanent optical access window in human patients. In this present study, we demonstrate repeated brain imaging of n = 5 mice using both OCT and LSI across the WttB implant over 4 weeks. The main objectives are to determine if the WttB implant allows for chronic OCT imaging, and to shed further light on the question of whether optical access provided by the WttB implant remains stable over this duration in the body. The Window to the Brain implant allowed for stable repeated imaging of the mouse brain with Optical Coherence Tomography over 28 days, without loss of signal intensity. Repeated Laser Speckle Imaging was also possible over this timeframe, but signal to noise ratio and the sharpness of vessels in the images decreased with time. This can be partially explained by elevated blood flow during the first imaging session in response to trauma from the surgery, which was also detected by OCT flow imaging. These results are promising for long-term optical access through the WttB implant, making feasible chronic in vivo studies in multiple neurological models of brain disease.
| S-EPMC7339873 | biostudies-literature
Project description:Materials for applications in hostile environments, such as nuclear reactors or radioactive waste immobilization, require extremely high resistance to radiation damage, such as resistance to amorphization or volume swelling. Nanocrystalline materials have been reported to present exceptionally high radiation-tolerance to amorphization. In principle, grain boundaries that are prevalent in nanomaterials could act as sinks for point-defects, enhancing defect recombination. In this paper we present evidence for this mechanism in nanograined Yttria Stabilized Zirconia (YSZ), associated with the observation that the concentration of defects after irradiation using heavy ions (Kr(+), 400 keV) is inversely proportional to the grain size. HAADF images suggest the short migration distances in nanograined YSZ allow radiation induced interstitials to reach the grain boundaries on the irradiation time scale, leaving behind only vacancy clusters distributed within the grain. Because of the relatively low temperature of the irradiations and the fact that interstitials diffuse thermally more slowly than vacancies, this result indicates that the interstitials must reach the boundaries directly in the collision cascade, consistent with previous simulation results. Concomitant radiation-induced grain growth was observed which, as a consequence of the non-uniform implantation, caused cracking of the nano-samples induced by local stresses at the irradiated/non-irradiated interfaces.
| S-EPMC4291567 | biostudies-other
Project description:As a high-quality thermal barrier coating material, yttria-stabilized zirconia (YSZ) can effectively reduce the temperature of the collective materials to be used on the surface of gas turbine hot-end components. The bonding strength between YSZ and the substrate is also one of the most important factors for the applications. Herein, the Gaussian mixture model (GMM) and support vector regression (SVR) were used to construct a machine learning model between YSZ coating bonding strength and atmospheric plasma spraying (APS) process parameters. First, GMM was used to expand the original 8 data points to 400 with the R value of leave-one-out cross-validation improved from 0.690 to 0.990. Then, the specific effects of APS process parameters were explored through Shapley additive explanations and sensitivity analysis. Principal component analysis was used to explain the constructed model and obtain the optimized area with a high bonding strength. After experimental validation, the results showed that under the APS process parameters of a current of 617 A, a voltage of 65 V, a H2 flow of 3 L min-1, and a thickness of 200 μm, the bonding strength increased by more than 19% to 55.5 MPa compared with the original maximum value of 46.6 MPa, indicating that the constructed GMM-SVR model can accurately predict the bonding strength of YSZ coating.
| S-EPMC9219529 | biostudies-literature
Project description:The interfacial hydration structure of yttria-stabilized cubic zirconia (110) surface in contact with water was determined with ~0.5 Å resolution by high-resolution X-ray reflectivity measurement. The terminal layer shows a reduced electron density compared to the following substrate lattice layers, which indicates there are additional defects generated by metal depletion as well as intrinsic oxygen vacancies, both of which are apparently filled by water species. Above this top surface layer, two additional adsorbed layers are observed forming a characteristic interfacial hydration structure. The first adsorbed layer shows abnormally high density as pure water and likely includes metal species, whereas the second layer consists of pure water. The observed interfacial hydration structure seems responsible for local equilibration of the defective surface in water and eventually regulating the long-term degradation processes. The multitude of water interactions with the zirconia surface results in the complex but highly ordered interfacial structure constituting the reaction front.
| S-EPMC4908582 | biostudies-literature
Project description:Bacterial adhesion to implant biomaterials constitutes a virulence factor leading to biofilm formation, infection and treatment failure. The aim of this study was to examine the initial bacterial adhesion on different implant materials in vitro. Four implant biomaterials were incubated with Enterococcus faecalis, Staphylococcus aureus and Candida albicans for 2 h: 3 mol % yttria-stabilized tetragonal zirconia polycrystal surface (B1a), B1a with zirconium oxide (ZrO₂) coating (B2a), B1a with zirconia-based composite coating (B1b) and B1a with zirconia-based composite and ZrO₂ coatings (B2b). Bovine enamel slabs (BES) served as control. The adherent microorganisms were quantified and visualized using scanning electron microscopy (SEM); DAPI and live/dead staining. The lowest bacterial count of E. faecalis was detected on BES and the highest on B1a. The fewest vital C. albicans strains (42.22%) were detected on B2a surfaces, while most E. faecalis and S. aureus strains (approximately 80%) were vital overall. Compared to BES; coated and uncoated zirconia substrata exhibited no anti-adhesive properties. Further improvement of the material surface characteristics is essential.
| S-EPMC5452733 | biostudies-other
Project description:Yttria-stabilized zirconia (YSZ) nanospheres were synthesized by calcination at 900 °C after the adsorption of Y3+ ions into the pores of a zirconium-based metal-organic framework (MOF). The synthesized 3YSZ (zirconia doped with 3 mol% Y2O3), 8YSZ (8 mol% Y2O3), and 30YSZ (30 mol% Y2O3) nanospheres were found to exhibit uniform sizes and shapes. Complex permittivity and complex permeability were carried out in K-band (i.e., 18-26.5 GHz) to determine their suitability for use as low-k materials in 5G communications. The real and imaginary parts of the permittivity of the sintered 3YSZ were determined to be 21.24 and 0.12, respectively, while those of 8YSZ were 22.80 and 0.16, and those of 30YSZ were 7.16 and 0.38. Control of the real part of the permittivity in the sintered YSZ was facilitated by modifying the Y2O3 content, thereby rendering this material an electronic ceramic with potential for use in high-frequency 5G communications due to its excellent mechanical properties, high chemical resistance, and good thermal stability. In particular, it could be employed as an exterior material for electronic communication products requiring the minimization of information loss.
| S-EPMC9824511 | biostudies-literature
Project description:Solid oxide fuel cells (SOFCs) are promising electrochemical energy conversion devices owing to their high power generation efficiency and environmentally benign operation. Micro-tubular SOFCs, which have diameters ranging from a few millimeters to the sub-millimeter scale, offer several advantages over competing SOFCs such as high volumetric power density, good endurance against thermal cycling, and flexible sealing between fuel and oxidant streams. Herein, we successfully realized a novel micro-tubular SOFC design based on a porous yttria-stabilized zirconia (YSZ) support using multi-step dip coating and co-sintering methods. The micro-tubular SOFC consisted of Ni-YSZ, YSZ, and strontium-doped lanthanum manganite (LSM)-YSZ as the anode, electrolyte, and cathode, respectively. In addition, to facilitate current collection from the anode and cathode, Ni and LSM were applied as an anode current collector and cathode current collector, respectively. Micro-crystalline cellulose was selected as a pore former to achieve better shrinkage behavior of the YSZ support so that the electrolyte layer could be densified at a co-sintering temperature of 1300 °C. The developed micro-tubular design showed a promising electrochemical performance with maximum power densities of 525, 442, and 354 mW cm(-2) at 850, 800, and 750 °C, respectively.
| S-EPMC4148670 | biostudies-other
Project description:The carbon dioxide reforming of methane has attracted attention from researchers owing to its possibility of both mitigating the hazards of reactants and producing useful chemical intermediates. In this framework, the activity of the nickel-based catalysts, supported by yttria-stabilized zirconia and promoted with holmium oxide (Ho2O3), was assessed in carbon dioxide reforming of methane at 800 °C. The catalysts were characterized by N2-physisorption, H2 temperature-programmed reduction, temperature-programmed desorption of CO2, X-ray diffraction, scanning electron microscopy (SEM) together with energy-dispersive X-ray spectroscopy, transmission electron microscopy (TEM), and thermogravimetric analysis (TGA) techniques. The effect of holmium oxide weight percent loading (0.0, 1.0, 2.0, 3,0, 4.0, and 5.0 wt %) was examined owing to its impact on the developed catalysts. The optimum loading of Ho2O3 was found to be 4.0 wt %, where the methane and carbon dioxide conversions were 85 and 91%, respectively. The nitrogen adsorption-desorption isotherms specified the mesoporous aspect of the catalysts, while the SEM images displayed a morphology of agglomerated, porous particles. The TEM images of the spent catalyst displayed the formation of multiwalled carbon nanotubes. TGA of the 4.0 wt % of Ho2O3 catalyst, experimented over 7-hour time-on-stream, displayed little weight loss (<14.0 wt %) owing to carbon formation, indicating the good resistance of the catalyst to carbon accumulation due to the enhancing ability of Ho2O3 and its adjustment of the support.
| S-EPMC9730481 | biostudies-literature
Project description:It is known that the yttria-stabilized zirconia (YSZ) material has superior thermal, mechanical, and electrical properties. This material is used for manufacturing products and components of air heaters, hydrogen reformers, cracking furnaces, fired heaters, etc. This work is aimed at searching for the optimal sintering mode of YSZ ceramics that provides a high crack growth resistance. Beam specimens of ZrO2 ceramics doped with 6, 7, and 8 mol% Y2O3 (hereinafter: 6YSZ, 7YSZ, and 8YSZ) were prepared using a conventional sintering technique. Four sintering temperatures (1450 °C, 1500 °C, 1550 °C, and 1600 °C) were used for the 6YSZ series and two sintering temperatures (1550 °C and 1600 °C) were used for the 7YSZ and 8YSZ series. The series of sintered specimens were ground and polished to reach a good surface quality. Several mechanical tests of the materials were performed, namely, the microhardness test, fracture toughness test by the indentation method, and single-edge notch beam (SENB) test under three-point bending. Based on XRD analysis, the phase balance (percentages of tetragonal, cubic, and monoclinic ZrO2 phases) of each composition was substantiated. The morphology of the fracture surfaces of specimens after both the fracture toughness tests was studied in relation to the mechanical behavior of the specimens and the microstructure of corresponding materials. SEM-EDX analysis was used for microstructural characterization. It was found that both the yttria percentage and sintering temperature affect the mechanical behavior of the ceramics. Optimal chemical composition and sintering temperature were determined for the studied series of ceramics. The maximum transformation toughening effect was revealed for ZrO2-6 mol% Y2O3 ceramics during indentation. However, in the case of a SENB test, the maximum transformation toughening effect in the crack tip vicinity was found in ZrO2-7 mol% Y2O3 ceramics. The conditions for obtaining YSZ ceramics with high fracture toughness are discussed.
| S-EPMC9030607 | biostudies-literature