Dataset Information

Dataset for comparison between single and double pilot injection in diesel-natural gas dual fuel engine.

ABSTRACT: The present data article is based on the research work which investigates the low-temperature combustion (LTC) in a dual fuel light duty engine. The LTC mode was activated by means of double pilot injection to control the energy release rate in the first combustion stage, thereby minimizing the increase of the rate of pressure and allowing the operation under LTC. This data article presents all the data which supports the choice for double pilot injection vs single pilot injection for that research. In this experimental work the engine was fueled with diesel, in full-diesel (FD) mode, and in dual fuel (DF) mode with natural gas and natural gas - hydrogen mixtures as main fuel. In DF mode the pilot diesel fuel was injected both with a single and a double injection at the same engine speed and torque. The pressure cycle in one of the four cylinders, the intake manifold pressure and the injector current signal were acquired on a crank angle basis for 100 consecutive engine cycles. Analysis of combustion rate, maximum pressure rise and fuel/air flow rate were performed. The data set, which also includes some engine control parameters, the combustion chamber geometry and some injector features, can potentially be reused to numerically model the combustion phenomena and, in particular, to investigate the effect on the ignition phase of combustion in LTC, also considering the variability from cycle to cycle.

SUBMITTER: De Simio L

PROVIDER: S-EPMC6923486 | biostudies-literature | 2020 Feb

REPOSITORIES: biostudies-literature

ACCESS DATA

Publications

Dataset for comparison between single and double pilot injection in diesel-natural gas dual fuel engine.

De Simio Luigi L Iannaccone Sabato S

Data in brief 20191210

The present data article is based on the research work which investigates the low-temperature combustion (LTC) in a dual fuel light duty engine. The LTC mode was activated by means of double pilot injection to control the energy release rate in the first combustion stage, thereby minimizing the increase of the rate of pressure and allowing the operation under LTC. This data article presents all the data which supports the choice for double pilot injection vs single pilot injection for that resea ...[more]

PMID: 31890804

Similar Datasets

Project description:In this work, military jet fuel JP-5 surrogates were formulated and tested in comparison to a nominal JP-5 fuel. Combustion experiments were conducted in an advanced engine technology (AET) ignition quality tester (IQT) and a Yanmar L100W Tier 4 diesel engine due to the potential use of jet fuel in diesel engines in military situations. The surrogate development process began with determining the fuel chemical composition based on analyses of 256 JP-5 fuel samples. The physical and chemical properties of density, viscosity, flash point, surface tension, speed of sound, and distillation behavior guided the selection of the surrogate components and their composition. JP-5 differs from other aviation fuels in its properties, but most importantly in flash point, which is higher for safety purposes. Surrogates were prepared from n-dodecane, n-butylbenzene, 1-methylnaphthalene, tetralin, trans-decalin, iso-cetane, and n-butylcyclohexane as representatives of seven of the nine major chemical categories found in jet fuel. The mass fraction of each compound in the surrogates that fell within the range for that chemical class was found in real JP-5 fuels. After optimizing the surrogates for physical and chemical properties, six surrogates were selected for combustion testing in the Yanmar diesel engine, one of which was specifically selected for a low-derived cetane number (DCN). This surrogate performed poorly in the Yanmar engine. Four of the remaining five surrogates performed similarly to the baseline JP-5 in the diesel engine in terms of values and variability of ignition delay, rate of heat release, peak pressure, and the crank angle at which 50% of the fuel is burned. Of the six surrogates tested, the best one in terms of physical properties, chemical properties, and combustion behavior was the one that contained 0.2421, 0.1503, 0.0500, 0.0141, 0.0121, 0.2532, and 0.2782 mass percentages of n-dodecane, n-butylbenzene, 1-methylnaphthalene, tetralin, trans-decalin, iso-cetane, and n-butylcyclohexane, respectively.

Project description:A series of laboratory tests were conducted to assess the effects of Fe-containing fuel additives on aerosols emitted by a diesel engine retrofitted with a sintered metal filter (SMF) system. Emission measurements performed upstream and downstream of the SMF system were compared, for cases when the engine was fueled with neat ultralow sulfur diesel (ULSD) and with ULSD treated with two formulations of additives containing Fe-based catalysts. The effects were assessed for four steady-state engine operating conditions and one transient cycle. The results showed that the SMF system reduced the average total number and surface area concentrations of aerosols by more than 100-fold. The total mass and elemental carbon results confirmed that the SMF system was indeed very effective in the removal of diesel aerosols. When added at the recommended concentrations (30 p.p.m. of iron), the tested additives had minor adverse impacts on the number, surface area, and mass concentrations of filter-out (FOut) aerosols. For one of the test cases, the additives may have contributed to measurable concentrations of engine-out (EOut) nucleation mode aerosols. The additives had only a minor impact on the concentration and size distribution of volatile and semi-volatile FOut aerosols. Metal analysis showed that the introduction of Fe with the additives substantially increased Fe concentration in the EOut, but the SMF system was effective in removal of Fe-containing aerosols. The FOut Fe concentrations for all three tested fuels were found to be much lower than the corresponding EOut Fe concentrations for the case of untreated ULSD fuel. The results support recommendations that these additives should not be used in diesel engines unless they are equipped with exhaust filtration systems. Since the tested SMF system was found to be very efficient in removing Fe introduced by the additives, the use of these additives should not result in a measurable increase in emissions of de novo generated Fe-containing aerosols. The findings from this study should promote a better understanding of the benefits and challenges of using sintered metal systems and fuel additives to control the exposure of underground miners and other workers to diesel aerosols and gases.

Project description:Biodiesel is regarded by many as a "greener" alternative fuel to petroleum diesel with potentially lower health risk. However, recent studies examining biodiesel particulate matter (PM) characteristics and health effects are contradictive, and typically utilize PM generated by passenger car engines in laboratory settings. There is a critical need to analyze diesel and biodiesel PM generated in a "real-world" setting where heavy duty-diesel (HDD) engines and commercially purchased fuel are utilized. This study compares the mass concentrations, chemical composition and cytotoxicity of real-world PM from combustion of both petroleum diesel and a waste grease 20% biodiesel blend (B20) at a community recycling center operating HDD nonroad equipment. PM was analyzed for metals, elemental/organic carbon (EC/OC), polycyclic aromatic hydrocarbons (PAHs), and nitro-polycyclic aromatic hydrocarbons (N-PAHs). Cytotoxicity in a human lung epithelial cell line (BEAS-2B) following 24h exposure to the real-world particles was also evaluated. On average, higher concentrations for both EC and OC were measured in diesel PM. B20 PM contained significantly higher levels of Cu and Mo whereas diesel PM contained significantly higher concentrations of Pb. Principal component analysis determined Mo, Cu, and Ni were the metals with the greatest loading factor, suggesting a unique pattern related to the B20 fuel source. Total PAH concentration during diesel fuel use was 1.9 times higher than during B20 operations; however, total N-PAH concentration was 3.3 times higher during B20 use. Diesel PM cytotoxicity was 8.5 times higher than B20 PM (p<0.05) in a BEAS-2B cell line. This study contributes novel data on real-world, nonroad engine sources of metals, PAH and N-PAH species, comparing tailpipe PM vs. PM collected inside the equipment cabin. Results suggest PM generated from burning petroleum diesel in nonroad engines may be more harmful to human health, but the links between exposure, composition and toxicity are not straightforward.

Dataset Information

Dataset for comparison between single and double pilot injection in diesel-natural gas dual fuel engine.

Publications

Dataset for comparison between single and double pilot injection in diesel-natural gas dual fuel engine.

Similar Datasets

OmicsDI is part of the ELIXIR infrastructure

Tweets