Dataset Information

Biomechanical Comparison of Two Pediatric Blade Plate Designs in Proximal Femoral Osteotomies.

ABSTRACT:

Background

Blade plates are frequently used for internal fixation following proximal femoral varus rotational osteotomy to treat hip dysplasia in children with cerebral palsy. Recently, cannulated blade plates with the option for a proximal locking screw have demonstrated ease of insertion and low complication rates. Although there are two commonly used blade plates with a proximal screw option, no comparison of their biomechanical profiles has been undertaken.

Questions/purposes

Our study sought to compare the structural properties under axial loading, as well as the biomechanical contribution of a proximal screw, of two different 90° cannulated blade plates designed for pediatric proximal femurs. Plate A has a hole distal to the blade designed to attach a plate inserter, through which a 3.5-mm non-locking cortical screw could be placed. Plate B has a threaded hole distal to the blade designed to accept a 3.5-mm locking screw.

Methods

Plate A and plate B were inserted into 33 left pediatric synthetic proximal femurs. Axial loading to failure of plate A with and without a proximal screw was compared to that of plate B with and without a proximal screw. An additional 10 samples using plate B, with and without a proximal locking screw, were tested in tension to quantify the effect of the proximal screw on pullout strength.

Results

Plate B failed at a higher axial load than plate A. The addition of a proximal screw did not affect the axial load to failure for either plate. Pullout testing revealed that blade plates fixed with the proximal screw failed in tension at a significantly higher load (856.3?±?120.9 N) than those without proximal fixation (68.1?±?9.3 N, p?ConclusionsPlate B failed at a higher axial load in biomechanical testing, likely related to differences in its design. The addition of a proximal screw did not increase the axial loading properties of the blade plate construct but did increase the pullout strength by a factor of 12. These results may be used to influence implant selection and post-operative rehabilitation following proximal femoral osteotomies in children.

SUBMITTER: Ruzbarsky JJ

PROVIDER: S-EPMC6973987 | biostudies-literature | 2020 Feb

REPOSITORIES: biostudies-literature

ACCESS DATA

Publications

Biomechanical Comparison of Two Pediatric Blade Plate Designs in Proximal Femoral Osteotomies.

Ruzbarsky Joseph J JJ Swarup Ishaan I Garner Matthew R MR Meyers Kathleen N KN Edobor-Osula Folorunsho F Widmann Roger F RF Scher David M DM

HSS journal : the musculoskeletal journal of Hospital for Special Surgery 20190326 1

<h4>Background</h4>Blade plates are frequently used for internal fixation following proximal femoral varus rotational osteotomy to treat hip dysplasia in children with cerebral palsy. Recently, cannulated blade plates with the option for a proximal locking screw have demonstrated ease of insertion and low complication rates. Although there are two commonly used blade plates with a proximal screw option, no comparison of their biomechanical profiles has been undertaken.<h4>Questions/purposes</h4> ...[more]

PMID: 32015744

Similar Datasets

Project description:BackgroundAn understudied area of proximal first metatarsal osteotomies is the effect on articular contact properties following the surgeries. Potential long-term risks include altered joint mechanics and possible arthritic progression. A biomechanical comparison of articular characteristics of the proximal opening wedge and Ludloff osteotomies was performed in this study. It was hypothesized that the proximal opening wedge osteotomy (POWO) would lead to greater alterations in articular contact properties along the first ray.MethodsSeven paired fresh-frozen below-knee cadaveric limbs with hallux valgus were selected. Specimens in each pair were tested in the intact state and then randomized to receive either a Ludloff or POWO. A 4-mm opening wedge osteotomy was used in all cases. Loading of the flexor hallucis longus was to 100 N using an instrumented tensioner. A 28-N load was added at the distal phalanx to simulate the ground reaction force. First metatarsophalangeal (MTP) and tarsometatarsal (TMT) articular properties were recorded simultaneously using 2 pressure sensors. For each state, a pressure map was generated and contact area, peak pressure, and center of pressure were calculated. Wilcoxon signed-rank test was used to assess statistical significance.ResultsAverage peak pressure was noted to be elevated at the MTP (4.6 vs 6.9 mPa, P = .04) and TMT (3.3 mPa vs 5.1 mPa, P = .30) joints when comparing the Ludloff and the POWO, respectively. Contact area was also noted to be lower in the POWO relative to the Ludloff for the MTP (86.6 vs 69.1 mm2, P = .30) but not the TMT joints (89.1 vs 88.5 mm2, P = .97). There was a slight plantar-lateral and dorsomedial shift in pressure at the MTP and TMT articulations, respectively, of the POWO relative to the Ludloff. A trend toward decreased contact force within the TMT joint was noted following opening wedge osteotomy relative to the intact state (103.8 vs 113.9 N, P = .31), while forces were elevated at the MTP joint (104.3 vs 96.0 N, P = .63), although not statistically significant. Smaller increases in TMT and MTP joint forces were noted following the Ludloff when compared to the intact state (95.6 vs 93.3 N at TMT and 109.2 vs 103.2 N at MTP).ConclusionPOWO can potentially change articular contact characteristics along the TMT and MTP articulations of the first ray. This could possibly lead to altered loading patterns and possible long-term damage vs other osteotomies.Clinical relevanceWhile it is unlikely that the changes observed with the sizes of the osteotomy commonly used would lead to long-term significant clinical consequences, further study with larger group sizes would be beneficial.

Project description:BACKGROUND:Treating proximal humerus fractures can be challenging because of large metaphyseal defects that conceal anatomical landmarks. In such cases, medial cortical support with, for example, calcar screws, is mandatory. Nevertheless, varus dislocations and implant failures in patients with impaired bone quality persist. Thus, the need for effective treatment of these patients exists. Hybrid double plate osteosynthesis was introduced as an alternative, yielding similar results as calcar screws. However, a biomechanical comparison of the stability of these two techniques is pending. METHODS:Cadaveric humeral specimens were treated with plate osteosynthesis and calcar screws (group 1, n = 9) or hybrid double plate osteosynthesis (group 2, n = 9) using a proximal humerus fracture model with a two-part fracture. Displacement, stiffness, failure mode, and ultimate load were examined biomechanically in a cyclic compressive-loading scenario. RESULTS:Although the hybrid double plate osteosynthesis (group 2) tended to confer higher stiffnesses than the medial support screws at higher cycles (group 1), this trend was below the level of significance. The displacement revealed non-significantly lower values for group 1 as compared with group 2 for cycles 50 and 2000, but at 5000 cycles, group 2 offered non-significantly lower displacement values than group 1. The ultimate load tended to be non-significantly higher in the hybrid double plate osteosynthesis group (group 2: 1342±369 N, group 1: 855±408 N). Both groups yielded similar failure rates, with the majority of failures in group 2 being gap closures (n = 8), whereas those in group 1 being plate dislocations (n = 4). CONCLUSIONS:The use of an additive plate osteosynthesis in the region of the bicipital groove may be a potential alternative to the previously-established method of using calcar screws. The biomechanical data obtained in this study suggests that hybrid double plate osteosynthesis is as rigid and robust as calcar screws.

Project description:Proximal humerus fractures are the third most common in the human body but their management remains controversial. Open reduction and internal fixation with plates is one of the leading modes of operative treatment for these fractures. The development of technologies and techniques for these plates, during the recent decades, promise a bright future for their clinical use. A comprehensive review of in vitro biomechanical studies is needed for the comparison of plates' mechanical performance and the testing methodologies. This will not only guide clinicians with plate selection but also with the design of future in vitro biomechanical studies. This review was aimed to systematically categorise and review the in vitro biomechanical studies of these plates based on their protocols and discuss their results. The technologies and techniques investigated in these studies were categorised and compared to reach a census where possible.Web of Science and Scopus database search yielded 62 studies. Out of these, 51 performed axial loading, torsion, bending and/or combined bending and axial loading while 11 simulated complex glenohumeral movements by using tendons. Loading conditions and set-up, failure criteria and performance parameters, as well as results for each study, were reviewed. Only two studies tested four-part fracture model while the rest investigated two- and three-part fractures. In ten studies, synthetic humeri were tested instead of cadaveric ones. In addition to load-displacement data, three-dimensional motion analysis systems, digital image correlation and acoustic emission testing have been used for measurement.Overall, PHILOS was the most tested plate and locking plates demonstrated better mechanical performance than non-locking ones. Conflicting results have been published for their comparison with non-locking blade plates and polyaxial locking screws. Augmentation with cement [calcium phosphate or poly(methyl methacrylate)] or allografts (fibular and femoral head) was found to improve bone-plate constructs' mechanical performance. Controversy still lies over the use of rigid and semi-rigid implants and the insertion of inferomedial screws for calcar region support. This review will guide the design of in vitro and in silico biomechanical tests and also supplement the study of clinical literature.

Project description:To compare the static and dynamic mechanical properties of a modified crossed cannulated screw (CS) configuration, the inverted triangle (IT) cannulated screw configuration, and a compression hip screw (CHS) with derotation screw in Pauwels type III femoral neck fractures.Thirty synthetic femora were divided into 3 groups, and vertical femoral neck osteotomies were made. Ten osteotomized femora were fixed with a CS configuration, 10 were fixed with 3 parallel screws in an IT configuration, and the remaining 10 osteotomized femora were fixed with a CHS construct. All groups were tested using a cyclic (up to 15,000 load cycles) axial loading protocol, and survivors were statically loaded to failure. Cycles to failure, load to failure, and stiffness were calculated. The Kaplan-Meier method was used to estimate survival functions and were compared among fixation methods. The relationship between construct structural properties (maximum load and stiffness) and treatment were assessed using general linear modeling.All CHS fixation constructs survived the 15,000 cycle loading protocol. They endured longer (P = 0.034) than the CS fixation constructs (mean failure 13,332 cycles), but were not different from IT fixation constructs (mean failure 13,592 cycles). Maximum loads to failure for CS (3870 N) and IT (3756 N) fixation constructs were not different, but were less (P < 0.0001) than the maximum loads to failure for the CHS fixation constructs (5654 N). These findings parallel the results of the axial stiffness measurements: CS fixation constructs (663.01 N/mm) were not stiffer than IT fixation constructs (620.0 N/mm), but were less (P = 0.0005) than the axial stiffness of the CHS fixation constructs (1241.86 N/mm).The biomechanical performance of the CHS fixation method was superior to both the CS fixation method and the IT fixation method using a synthetic femoral model and this test protocol. Biomechanical performance of the latter 2 groups was indistinguishable. We recommend the use of CHS with the derotational screw construct for Pauwels III femoral neck fractures whenever possible.

Dataset Information

Biomechanical Comparison of Two Pediatric Blade Plate Designs in Proximal Femoral Osteotomies.

Background

Questions/purposes

Methods

Results

Publications

Biomechanical Comparison of Two Pediatric Blade Plate Designs in Proximal Femoral Osteotomies.

Similar Datasets

OmicsDI is part of the ELIXIR infrastructure

Tweets