Electrospun Polymers in Cartilage Engineering-State of Play.
Ontology highlight
ABSTRACT:
SUBMITTER: Yilmaz EN
PROVIDER: S-EPMC7039817 | biostudies-literature | 2020
REPOSITORIES: biostudies-literature
Publications
Electrospun Polymers in Cartilage Engineering-State of Play.
Yilmaz Elif Nur EN Zeugolis Dimitrios I DI
Frontiers in bioengineering and biotechnology 20200218
Articular cartilage defects remain a clinical challenge. Articular cartilage defects progress to osteoarthritis, which negatively (e.g., remarkable pain, decreased mobility, distress) affects millions of people worldwide and is associated with excessive healthcare costs. Surgical procedures and cell-based therapies have failed to deliver a functional therapy. To this end, tissue engineering therapies provide a promise to deliver a functional cartilage substitute. Among the various scaffold fabri ...[more]
Similar Datasets
Project description:Treatment of full-thickness damage to hyaline cartilage is hampered by the limited availability of autologous healthy cartilage and the lengthy, cost-prohibitive cell isolation and expansion steps associated with autologous cartilage implantation (ACI). Here we report a strategy for de novo engineering of ectopic autologous cartilage (EAC) within the subperiosteal space (in vivo bioreactor), through the mere introduction of a biocompatible gel that might promote hypoxia-mediated chondrogenesis, thereby effectively overcoming the aforementioned limitations. The EAC is obtained within 3 wk post injection of the gel, and can be press-fit into an osteochondral defect where it undergoes remodeling with good lateral and subchondral integration. The implanted EAC showed no calcification even after 9 mo and attained an average O'Driscoll score of 11 (versus 4 for controls). An "on demand" autologous source of autologous cartilage with remodeling capacity is expected to significantly impact the clinical options in repair of trauma to articular cartilage.
| S-EPMC2840469 | biostudies-literature
Project description:Corneal diseases constitute the second leading cause of vision loss and affect more than 10 million people globally. As there is a severe shortage of fresh donated corneas and an unknown risk of immune rejection with traditional heterografts, it is very important and urgent to construct a corneal equivalent to replace pathologic corneal tissue. Corneal tissue engineering has emerged as a practical strategy to develop corneal tissue substitutes, and the design of a scaffold with mechanical properties and transparency similar to that of natural cornea is paramount for the regeneration of corneal tissues. Nanofibrous scaffolds produced by electrospinning have high surface area-to-volume ratios and porosity that simulate the structure of protein fibers in native extra cellular matrix (ECM). The versatilities of electrospinning of polymer components, fiber structures, and functionalization have made the fabrication of nanofibrous scaffolds with suitable mechanical strength, transparency and biological properties for corneal tissue engineering feasible. In this paper, we review the recent developments of electrospun scaffolds for engineering corneal tissues, mainly including electrospun materials (single and blended polymers), fiber structures (isotropic or anisotropic), functionalization (improved mechanical properties and transparency), applications (corneal cell survival, maintenance of phenotype and formation of corneal tissue) and future development perspectives.
| S-EPMC5509008 | biostudies-other
Project description:BackgroundBone marrow-derived stem cells (BMSCs) and chondrocytes have been reported to present "dedifferentiation" and "phenotypic loss" during the chondrogenic differentiation process in cartilage tissue engineering, and cartilage progenitor cells (CPCs) are novel seeding cells for cartilage tissue engineering. In our previous study, cartilage progenitor cells from different subtypes of cartilage tissue were isolated and identified in vitro, but the study on in vivo chondrogenic characteristics of cartilage progenitor cells remained rarely. In the current study, we explored the feasibility of combining cartilage progenitor cells with poly(3-hydroxybutyrate-co-3-hydroxyvalerate) (PHBV) to produce tissue-engineered cartilage and compared the proliferation ability and chondrogenic characteristics of cartilage progenitor cells with those of bone marrow-derived stem cells and chondrocytes.MethodsThese three cells combined with PHBV were cultured in vitro for 1 week without chondrogenic induction and then transplanted subcutaneously into nude mice for 6 weeks. The cell-PHBV constructs were evaluated by gross observation, histological staining, glycosaminoglycan content measurement, biomechanical analysis and RT-PCR.ResultsThe chondrocyte-PHBV constructs and CPC-PHBV constructs became an ivory-whitish cartilage-like tissue, while the BMSC-PHBV constructs became vascularized 6 weeks after the subcutaneous implantation. Histological examination showed that many typical cartilage structures were present in the chondrocyte group, some typical cartilage structures were observed in the CPC group, while no typical cartilage structures were observed in the BMSC group.ConclusionsCartilage progenitor cells may undergo chondrogenesis without chondrogenic induction and are better at chondrogenesis than BMSCs but worse than chondrocytes in the application of cartilage tissue engineering.
| S-EPMC6441183 | biostudies-literature
Project description:Natural polysaccharide pectin has for the first time been grafted with polyhydroxybutyrate (PHB) via ring-opening polymerization of ?-butyrolactone. This copolymer, pectin-polyhydroxybutyrate (pec-PHB), was blended with PHB in various proportions and electrospun to produce nanofibers that exhibited uniform and bead-free nanostructures, suggesting the miscibility of PHB and pec-PHB. These nanofiber blends exhibited reduced fiber diameters from 499 to 336-426 nm and water contact angles from 123.8 to 88.2° on incorporation of pec-PHB. They also displayed 39-335% enhancement of elongation at break relative to pristine PHB nanofibers. pec-PHB nanofibers were found to be noncytotoxic and biocompatible. Human retinal pigmented epithelium (ARPE-19) cells were seeded onto pristine PHB and pec-PHB nanofibers as scaffold and showed good proliferation. Higher proportions of pec-PHB (pec-PHB10 and pec-PHB20) yielded higher densities of cells with similar characteristics to normal RPE cells. We propose, therefore, that nanofibers of pec-PHB have significant potential as retinal tissue engineering scaffold materials.
| S-EPMC6044805 | biostudies-literature
Project description:ObjectivesAmongst the fourth generation of PHAs is bio-plasticpoly3-hydroxybutyrate4-hydroxybutyrate (P34HB); it is thus appropriate to perform novel research on its uses and applications. The main objective of this study was to determine whether electrospun P34HB fibres would accommodate viability, growth and differentiation of mouse adipose-derived stem cells (mASCs).Materials and methodsIn the present study, we looked at P34HB in two forms, electrospun P34HB fibres and P34HB film. Morphology of electrospun P34HB fibres and P34HB film were characterized using scanning electron microscopy, fluorescence microscopy and confocal laser scanning microscopy, after cell seeding. Cell adhesion, proliferation and cytotoxicity tests were conducted on both by MTT and CCK-8 assays, respectively. After being cultured with osteogenic induction, expression of adipogenic genes Runx2, OPN and OCN, were examined by real-time PCR.ResultsBy scanning electron microscopy, light microscopy and confocal laser scanning microscopy, we observed that the mASCs grew well associated with the P34HB materials. After MTT and CCK-8 assay, we concluded that P34HB would, indeed, be a material suitable for further cell adhesion and proliferation studies. More importantly, we found that the P34HB matrices promoted expression of Runx2, OPN and OCN with osteogenic induction.ConclusionsIn this investigation, we can confirm that the electrospun P34HB fibres accommodated survival, proliferation and differentiation of mASCs, and we have been able to draw the conclusion that fibre scaffolds produced by the electrospinning process are promising for application of bone tissue engineering.
| S-EPMC6495184 | biostudies-literature
Project description:Heart failure is a morbid disorder characterized by progressive cardiomyocyte (CM) dysfunction and death. Interest in cell-based therapies is growing, but sustainability of injected CMs remains a challenge. To mitigate this, we developed an injectable biomimetic Reverse Thermal Gel (RTG) specifically engineered to support long-term CM survival. This RTG biopolymer provided a solution-based delivery vehicle of CMs, which transitioned to a gel-based matrix shortly after reaching body temperature. In this study we tested the suitability of this biopolymer to sustain CM viability. The RTG was biomolecule-functionalized with poly-l-lysine or laminin. Neonatal rat ventricular myocytes (NRVM) and adult rat ventricular myocytes (ARVM) were cultured in plain-RTG and biomolecule-functionalized-RTG both under 3-dimensional (3D) conditions. Traditional 2D biomolecule-coated dishes were used as controls. We found that the RTG-lysine stimulated NRVM to spread and form heart-like functional syncytia. Regarding cell contraction, in both RTG and RTG-lysine, beating cells were recorded after 21 days. Additionally, more than 50% (p value < 0.05; n = 5) viable ARVMs, characterized by a well-defined cardiac phenotype represented by sarcomeric cross-striations, were found in the RTG-laminin after 8 days. These results exhibit the tremendous potential of a minimally invasive CM transplantation through our designed RTG-cell therapy platform.
| S-EPMC4863197 | biostudies-literature
Project description:BACKGROUND:To overcome the potential drawbacks of a short half-life and dose-related adverse effects of using active transforming growth factor-beta 1 for cartilage engineering, a cell-mediated latent growth factor activation strategy was developed incorporating latent transforming growth factor-?1 (LTGF) into an electrospun poly(L-lactide) scaffold. METHODS:The electrospun scaffold was surface modified with NH3 plasma and biofunctionalised with LTGF to produce both random and orientated biofunctionalised electrospun scaffolds. Scaffold surface chemical analysis and growth factor bioavailability assays were performed. In vitro biocompatibility and human nasal chondrocyte gene expression with these biofunctionalised electrospun scaffold templates were assessed. In vivo chondrogenic activity and chondrocyte gene expression were evaluated in athymic rats. RESULTS:Chemical analysis demonstrated that LTGF anchored to the scaffolds was available for enzymatic, chemical and cell activation. The biofunctionalised scaffolds were non-toxic. Gene expression suggested chondrocyte re-differentiation after 14 days in culture. By 6 weeks, the implanted biofunctionalised scaffolds had induced highly passaged chondrocytes to re-express Col2A1 and produce type II collagen. CONCLUSIONS:We have demonstrated a proof of concept for cell-mediated activation of anchored growth factors using a novel biofunctionalised scaffold in cartilage engineering. This presents a platform for development of protein delivery systems and for tissue engineering.
| S-EPMC3840173 | biostudies-literature
Project description:Controlling the structure and organization of electrospun fibers is desirable for fabricating scaffolds and materials with defined microstructures. However, the effects of microtopography on the deposition and, in turn, the organization of the electrospun fibers are not well understood. In this study, conductive polydimethylsiloxane (PDMS) templates with different micropatterns were fabricated by combining photolithography, silicon wet etching, and PDMS molding techniques. The fiber organization was varied by fine-tuning the microtopography of the electrospinning collector. Fiber conformity and alignment were influenced by the depth and the slope of microtopography features, resulting in scaffolds comprising either an array of microdomains with different porosity and fiber alignment or an array of microwells. Microtopography affected the fiber organization for hundreds of micrometers below the scaffold surface, resulting in scaffolds with distinct surface properties on each side. In addition, the fiber diameter was also affected by the fiber conformity. The effects of the fiber arrangement in the scaffolds on the morphology, migration, and infiltration of cells were examined by in vitro and in vivo experiments. Cell morphology and organization were guided by the fibers in the microdomains, and cell migration was enhanced by the aligned fibers and the three-dimensional scaffold structure. Cell infiltration was correlated with the microdomain porosity. Microscale control of the fiber organization and the porosity at the surface and through the thickness of the fibrous scaffolds, as demonstrated by the results of this study, provides a powerful means of engineering the three-dimensional structure of electrospun fibrous scaffolds for cell and tissue engineering.
| S-EPMC3733537 | biostudies-literature
Project description:Electrospinning is an attractive fabrication process providing a cost-effective and straightforward technic to make extra-cellular matrix (ECM) mimicking scaffolds that can be used to replace or repair injured tissues and organs. Synthetic polymers as poly (?-caprolactone) (PCL) and poly (ethylene oxide terephthalate)-poly(butylene terephthalate) (PEOT/PBT) have been often used to produce scaffolds due to their good processability, mechanical properties, and suitable biocompatibility. While synthetic polymers can mimic the physical features of native ECM, natural polymers like alginate are better suited to recapitulate its hydrated state or introduce functional groups that are recognized by cells (e.g., -NH2). Thus, this study aims at creating electrospun meshes made of blended synthetic and natural polymers for tissue engineering applications. Polyethylene oxide (PEO), PCL, and PEOT/PBT were used as a carrier of Alginate. Scaffolds were electrospun at different flow rates and distances between spinneret and collector (air gap), and the resulting meshes were characterized in terms of fiber morphology, diameter, and mesh inter-fiber pore size. The fiber diameter increased with increasing flow rate, while there was no substantial influence of the air gap. On the other hand, the mesh pore size increased with increasing air gap, while the effect of flow rate was not significant. Cross-linking and washing of alginate electrospun scaffolds resulted in smaller fiber diameter. These newly developed scaffolds may find useful applications for tissue engineering strategies as they resemble physical and chemical properties of tissue ECM. Human Dermal Fibroblasts were cultured on PCL and PCL/Alginate scaffolds in order to create a dermal substitute.
| S-EPMC6798037 | biostudies-literature
Project description:ObjectiveDespite new strategies in tissue engineering, cartilage repair remains a major challenge. Our aim is to treat patients with focal lesions of articular cartilage with autologous hyaline cartilage implants using a scaffold-free approach. In this article, we describe experiments to optimize production of scaffold-free cartilage discs.DesignArticular chondrocytes were expanded in vitro, seeded in transwell inserts and redifferentiated using established chondrogenic components. Experimental variables included testing 2 different expansion media, adding bone morphogenetic protein 2 (BMP2), insulin-like growth factor 1 (IGF1), growth/differentiation factor 5 (GDF5), or fibroblast growth factor 18 (FGF18) to the differentiation medium and allowing the disc to float freely in large wells. Cartilage discs were analyzed by weight and thickness, real-time RT-qPCR (reverse transcriptase qualitative polymerase chain reaction), fluorescence immunostaining, transmission electron microscopy, second harmonic generation imaging, and measurement of Young's modulus.ResultsAddition of BMP2 to the chondrogenic differentiation medium (CDM) was essential for stable disc formation, while IGF1, GDF5, and FGF18 were redundant. Allowing discs to float freely in CDM on a moving platform increased disc thickness compared with discs kept continuously in transwell inserts. Discs cultured for 6 weeks reached a thickness of almost 2 mm and Young's modulus of >200 kPa. There was abundant type II collagen. Collagen fibrils were 25 nm thick, with a tendency to be organized perpendicular to the disc surface.ConclusionScaffold-free engineering using BMP2 and providing free movement in CDM produced firm, elastic cartilage discs with abundant type II collagen. This approach may potentially be used in clinical trials.
| S-EPMC8725371 | biostudies-literature