Browse
Submit Data
Databases
API
Help

Dataset Information

0 Views

0 Connections

0 Citations

0 Reanalyses

0 Downloads

Omics score: 0

Corrosion Resistance of Heat-Treated Ni-W Alloy Coatings.

ABSTRACT: The paper presents research on evaluation of corrosion resistance of Ni-W alloy coatings subjected to heat treatment. The corrosion resistance was tested in 5% NaCl solution by the use of potentiodynamic polarization technique and electrochemical impedance spectroscopy. Characteristics of the Ni-W coatings after heat treatment were carried out using scanning electron microscopy, scanning Kelvin probe technique and X-ray diffraction. Suggested reasons for the improvement of properties of the heat treated Ni-W coating, obtained at the lowest current density value (125 mA?cm-2), are the highest tungsten content (c.a. 25 at.%) as well as the smallest and the most homogeneous electrochemically active surface area.

SUBMITTER: Popczyk M

PROVIDER: S-EPMC7085042 | biostudies-literature | 2020 Mar

REPOSITORIES: biostudies-literature

ACCESS DATA

Json Xml

Publications

Corrosion Resistance of Heat-Treated Ni-W Alloy Coatings.

Popczyk Magdalena M Kubisztal Julian J Swinarew Andrzej Szymon AS Waśkiewicz Zbigniew Z Stanula Arkadiusz A Knechtle Beat B

Materials (Basel, Switzerland) 20200306 5

The paper presents research on evaluation of corrosion resistance of Ni-W alloy coatings subjected to heat treatment. The corrosion resistance was tested in 5% NaCl solution by the use of potentiodynamic polarization technique and electrochemical impedance spectroscopy. Characteristics of the Ni-W coatings after heat treatment were carried out using scanning electron microscopy, scanning Kelvin probe technique and X-ray diffraction. Suggested reasons for the improvement of properties of the heat ...[more]

PMID: 32155698

Similar Datasets

Oxyhydroxide-Coated PEO-Treated Mg Alloy for Enhanced Corrosion Resistance and Bone Regeneration.

Project description:Plasma electrolytic oxidation (PEO) is widely used as a surface modification method to enhance the corrosion resistance of Mg alloy, the most likely applied biodegradable material used in orthopedic implants. However, the pores and cracks easily formed on the PEO surface are unfavorable for long-term corrosion resistance. In this study, to solve this problem, we used simple immersion processes to construct Mn and Fe oxyhydroxide duplex layers on the PEO-treated AZ31 (PEO-Mn/Fe). As control groups, single Mn and Fe oxyhydroxide layers were also fabricated on PEO (denoted as PEO-Mn and PEO-Fe, respectively). PEO-Mn showed a similar porous morphology to the PEO sample. However, the PEO-Fe and PEO-Mn/Fe films completely sealed the pores on the PEO surfaces, and no cracks were observed even after the samples were immersed in water for 7 days. Compared with PEO, PEO-Mn, and PEO-Fe, PEO-Mn/Fe exhibited a significantly lower self-corrosion current, suggesting better corrosion resistance. In vitro C3H10T1/2 cell culture showed that PEO-Fe/Mn promoted the best cell growth, alkaline phosphatase activity, and bone-related gene expression. Furthermore, the rat femur implantation experiment showed that PEO-Fe/Mn-coated Mg showed the best bone regeneration and osteointegration abilities. Owing to enhanced corrosion resistance and osteogenesis, the PEO-Fe/Mn film on Mg alloy is promising for orthopedic applications.

| S-EPMC9149893 | biostudies-literature

Microhardness and In Vitro Corrosion of Heat-Treated Mg-Y-Ag Biodegradable Alloy.

Project description:Magnesium alloys are promising candidates for biodegradable medical implants which reduce the necessity of second surgery to remove the implants. Yttrium in solid solution is an attractive alloying element because it improves mechanical properties and exhibits suitable corrosion properties. Silver was shown to have an antibacterial effect and can also enhance the mechanical properties of magnesium alloys. Measurements of microhardness and electrical resistivity were used to study the response of Mg-4Y and Mg-4Y-1Ag alloys to isochronal or isothermal heat treatments. Hardening response and electrical resistivity annealing curves in these alloys were compared in order to investigate the effect of silver addition. Procedures for solid solution annealing and artificial aging of the Mg-4Y-1Ag alloy were developed. The corrosion rate of the as-cast and heat-treated Mg-4Y-1Ag alloy was measured by the mass loss method. It was found out that solid solution heat treatment, as well artificial aging to peak hardness, lead to substantial improvement in the corrosion properties of the Mg-4Y-1Ag alloy.

| S-EPMC5344547 | biostudies-other

Improvement of AZ91 Alloy Corrosion Properties by Duplex NI-P Coating Deposition.

Project description:The corrosion behavior of duplex Ni-P coatings deposited on AZ91 magnesium alloy was studied. The electroless deposition process of duplex Ni-P coating consisted in the preparation of low-phosphorus Ni-P coating (5.7 wt.% of P), which served as a bond coating and high-phosphorus Ni-P coating (11.5 wt.% of P) deposited on it. The duplex Ni-P coatings with the thickness of 25, 50, 75 and 100 µm were deposited on AZ91 magnesium alloy. The electrochemical corrosion behavior of coated AZ91 magnesium alloy was investigated by electrochemical impedance spectroscopy and potentiodynamic polarization method in 0.1 M NaCl. Obtained results showed a significant improvement in the corrosion resistance of coated specimens when compared to uncoated AZ91 magnesium alloy. From the results of the immersion tests in 3.5 wt.% NaCl, 10% solution of HCl and NaOH and 5% neutral salt spray, a noticeable increase in the corrosion resistance with the increasing thickness of the Ni-P coating was observed.

| S-EPMC7142442 | biostudies-literature

Graphene-Reinforced Zn-Ni Alloy Composite Coating on Iron Substrates by Pulsed Reverse Electrodeposition and Its High Corrosion Resistance.

Project description:In this paper, a novel kind of graphene (Gr)-reinforced Zn-Ni alloy composite coating is successfully prepared on an iron substrate by pulsed reverse electrodeposition. Hydrophilic graphene oxide (GO) is directly added to the electrolyte and reduced to Gr during coating. The experimental results reveal that (1) there is an optimal adding amount (about 0.4 g/L) of GO in the electrolyte for achieving the highest mechanical properties and corrosion resistance; (2) the composite coating shows grain refinement and a dense microstructure due to heterogeneous nucleation sites provided from the Gr sheets during electrodeposition; and (3) compared to the regular Zn-Ni coating, the composite coating exhibits many enhancements, including hardness increase by 2.3 times, elastic modulus increase by 39%, and corrosion rate decrease from 37.66 to 1.30 mils/annum. This process has advantages such as being simple, effective, well repeatable, economical, and supporting large-scale production and is expected to be widely applied in electronics, automobiles, marine engineering, and military industries.

| S-EPMC8173559 | biostudies-literature

A Superior Corrosion Protection of Mg Alloy via Smart Nontoxic Hybrid Inhibitor-Containing Coatings.

Project description:The increase of corrosion resistance of magnesium and its alloys by forming the smart self-healing hybrid coatings was achieved in this work in two steps. In the first step, using the plasma electrolytic oxidation (PEO) treatment, a ceramic-like bioactive coating was synthesized on the surface of biodegradable MA8 magnesium alloy. During the second step, the formed porous PEO layer was impregnated with a corrosion inhibitor 8-hydroxyquinoline (8-HQ) and bioresorbable polymer polycaprolactone (PCL) in different variations to enhance the protective properties of the coating. The composition, anticorrosion, and antifriction properties of the formed coatings were studied. 8-HQ allows controlling the rate of material degradation due to the self-healing effect of the smart coating. PCL treatment of the inhibitor-containing layer significantly improves the corrosion and wear resistance and retains an inhibitor in the pores of the PEO layer. It was revealed that the corrosion inhibitor incorporation method (including the number of steps, impregnation, and the type of solvent) significantly matters to the self-healing mechanism. The hybrid coatings obtained by a 1-step treatment in a dichloromethane solution containing 6 wt.% polycaprolactone and 15 g/L of 8-HQ are characterized by the best corrosion resistance. This coating demonstrates the lowest value of corrosion current density (3.02 × 10-7 A cm-2). The formation of the hybrid coating results in the corrosion rate decrease by 18 times (0.007 mm year-1) as compared to the blank PEO layer (0.128 mm year-1). An inhibitor efficiency was established to be 83.9%. The mechanism of corrosion protection of Mg alloy via smart hybrid coating was revealed.

| S-EPMC10056050 | biostudies-literature

Effect of Heat Treatments on the Corrosion Resistance of a High Strength Mg-Gd-Y-Zn-Zr Alloy.

Project description:Magnesium-rare earth (Mg-Re) alloys are very promising structural materials in lightweight industries, while the poor corrosion resistance limits their widespread application. In this work, to provide insights into the functions of precipitate characteristics on the corrosion behaviors of Mg-Re alloys, the influence of heat treatments on the corrosion behavior of Mg-11.46Gd-4.08Y-2.09Zn-0.56Zr alloy was investigated via an immersion test, electrochemical experiment and scanning electron microscope (SEM). The results showed that the corrosion rate of Mg-11.46Gd-4.08Y-2.09Zn-0.56Zr alloy specimens decreased by 17.58% and 20.44% after T5 and T6 heat treatment, respectively. In the heat-treated specimens, the corrosion did not extend further into the matrix but formed fine corrosion grooves along the extrusion direction. The improved homogeneity reduced the residual stress and the β' precipitate introduced as a corrosion barrier after T5 and T6 heat treatment reduced the corrosion rate of the studied Mg alloy. In addition, the volume fraction of the long-period stacking-ordered (LPSO) phase decreased after heat treatment, which effectively reduced galvanic corrosion and enhanced the protective effect on the Mg matrix.

| S-EPMC9025149 | biostudies-literature

The Waterborne Superamphiphobic Coatings with Antifouling, High Temperature Resistance, and Corrosion Resistance.

Project description:Water-based superamphiphobic coatings are environment-friendly, which have attracted tremendous attention recently, but the performances are severely limited by the dispersibility of hydrophobic particles. To solve the poor dispersibility of modified silica powder with hydrophobicity, silica dispersion was blended with polytetrafluoroethylene (PTFE) emulsion and modified aluminum tripolyphosphate (ATP) dispersion to successfully prepare water-based coatings. Multifunctional coatings were prepared by one-step spraying. It possessed good adhesion (grade 1), excellent antifouling, impact resistance, chemical stability (acid and alkali resistance for 96 h of immersion), and corrosion resistance (3.5 wt % NaCl solutions for 20 days). More importantly, the superamphiphobic coatings had high contact angles (CAs) and low slide angles (SAs) for ethylene glycol (CAs = 154 ± 0.8°; SAs = 13 ± 0.7°) and water (CAs = 158 ± 0.7°; SAs = 4 ± 0.3°). Furthermore, the composite coating was still hydrophobic after 35 cycles of wear with high roughness sandpaper (120 mesh) under three different loads, which maintained superamphiphobicity at 425 °C. This work is expected to provide a facile idea and method for the preparation of waterborne superamphiphobic coatings.

| S-EPMC10116617 | biostudies-literature

Corrosion Resistance in Artificial Perspiration of Cr-Based Decorative Coatings.

Project description:We aim at developing hexavalent chromium-free coatings for frequently touched decorative parts. Cr(N,O) and multilayered CrN/CrO coatings were deposited by means of reactive magnetron sputtering. All samples presented good adhesion to the substrates enhanced by an epoxy layer designed to enhance PVD coating adhesion. Similar substrates are found in the automotive industry and can be used in appliances where a metallic finish is desired by the consumer. Corrosion behavior was induced, using artificial sweat to simulate long exposure to human touch for 96 h. In potentiodynamic polarization tests, the coatings were revealed to be nobler than the substrate alone. Cr displayed a non-existent passivation region, while gCrN exhibited a quick passivation of the surface and its respective breakdown and several current fluctuations, indicating the occurrence of pitting, which was confirmed by SEM micrography after the corrosion. Regarding EIS results, all films depicted a diminution of impedance modulus (|Z|) after 96 h, which indicates a diminution of corrosion resistance against artificial sweat. Nitride films exhibited the worst anticorrosive features. On the other hand, Cr and CrO exhibited the highest |Z| values. These results are corroborated by low the corrosion rates of both coatings. The equivalent electrical circuit allows us to confirm oxide formation in the outermost layer of the films due to electrolyte/surface interaction, indicating a self-protecting mechanism. Nitride films showed the lowest values and less corrosion resistance, confirming the results obtained in polarization potentiodynamic tests. The coatings developed in this work, namely Cr and CrO, showed a promising corrosion resistance behavior that could endure a lifetime of frequent human touch in various decorative applications either automotive or general appliances.

| S-EPMC10459534 | biostudies-literature

Influence of surface treatment on PEDOT coatings: surface and electrochemical corrosion aspects of newly developed Ti alloy.

Project description:Surface treatment of metallic materials prior to the application of polymer coatings plays an important role in providing improved surface features and enhanced corrosion protection. In the current investigation, we aimed to evaluate the effect of surface treatment of newly developed TiNbZr (TNZ) alloys on the surface characteristics, including the surface topography, morphology, hydrophobicity and adhesion strength of subsequent poly(3,4-ethylenedioxythiophene) (PEDOT) coatings. The surface morphology, chemical composition, and surface roughness of both treated and coated alloys were characterized by scanning electron microscopy, energy dispersive spectroscopy, and optical profilometry, respectively. The adhesion strength of the coating was measured using a micro scratch machine. Furthermore, we also evaluated the performance of electrochemically synthesized PEDOT coatings on surface-treated TNZ alloys in terms of the surface protective performance in simulated body fluid (SBF) and in vitro bioactivity in osteoblast MG63 cells. Surface analysis findings indicated that the nature of the PEDOT coating (surface morphology, topography, wettability and adhesion strength) was intensely altered, while the surface treatment performed before electrodeposition facilitated the overall performance of PEDOT coatings as implant coating materials. The obtained corrosion studies confirmed the enhanced corrosion protection performance of PEDOT coatings on treated TNZ substrates. In vitro cell culture studies validated the improved cell adhesion and proliferation rate, further highlighting the important role of surface treatment before electrodeposition.

| S-EPMC9080621 | biostudies-literature

Facile and Green Engineering Approach for Enhanced Corrosion Resistance of Ni-Cr-Al<sub>2</sub>O<sub>3</sub> Thermal Spray Coatings.

Project description:Thermal spray coatings (TSCs) are widely utilized for limiting degradation of structural components. However, the performance of TSCs is significantly impaired by its inherent non-homogeneous microstructure, comprising of splat boundaries, porosities, secondary phase-formation, and elemental segregation. Herein, we report a simplistic approach for significantly enhancing the corrosion resistance of TSCs. Ni-Cr-5Al2O3 coatings were deposited on stainless steel using high-velocity oxy-fuel technique. The microstructure of as-sprayed coating showed significant inhomogeneities in the form of isolated splats and elemental segregation. The microstructure of developed coatings was modified using a novel processing technique, known as stationary friction processing (SFP). The SFP treatment resulted in complete refinement of coating microstructure with elimination of splat boundaries and pores along with elemental homogenization. The corrosion behavior of as-sprayed and SFP treated coating was evaluated in 3.5% NaCl solution using potentiodynamic polarization and electrochemical impedance spectroscopy. The SFP treatment reduced the corrosion rate of as-sprayed coating by an order of magnitude. Long-time immersion studies showed continuously decreasing impedance of the as-sprayed coating due to the penetration of the electrolyte along the splat boundaries. In contrast, impedance for the SFP treated coating increased with the immersion time due to the removal of all microstructural defects.

| S-EPMC7528329 | biostudies-literature

OmicsDI is part of the ELIXIR infrastructure

OmicsDI is an Elixir interoperability service. Learn more ›

Tweets

OmicsDI Databases

PRIDE
PeptideAtlas
MassIVE
JPOST Repository
Physiome Model Repository

EGA
EVA
ENA
LINCS
PAXDB
Cell Collective

MetaboLights
Metabolomics Workbench
MetabolomeExpress
GNPS
BioModels
FAIRDOMHub

ArrayExpress
dbGaP
ExpressionAtlas
GEO
NODE

Information

Databases
Help
API
Contact us
Code on GitHub
Terms of use
Submit Data