Lubricated friction around nanodefects.
Ontology highlight
ABSTRACT:
SUBMITTER: Cafolla C
PROVIDER: S-EPMC7124950 | biostudies-literature |
REPOSITORIES: biostudies-literature
Similar Datasets
Project description:Energy dissipation due to friction and wear is reducing the energy efficiency and reliability of mechanical systems. Thus, great efforts are being made to minimize friction for technical applications. In our present work, we investigate the tribological behavior of stainless steel 100Cr6 with a-C:H and a-C:H:Si coating lubricated with a surface-active formanisotropic 1,3-diketone. The results show that superlow friction can be achieved on the macroscale using a steel 100Cr6 self pairing (COF ∼ 0.005) and with 100Cr6 in combination with a-C:H coating (COF ∼ 0.008). Furthermore, the replacement of steel with a-C:H coating leads to a considerable decrease of wear. The reduced COF arises from the chemical interaction of the lubricant with the surface and nascent iron ions. It was found that interfacial parameters correlate with tribological results. In addition, the alignment of the formanisotropic molecules in the tribological contact at thin-film lubrication leads to an anisotropic viscosity with a minimum shear resistance in sliding direction. Atomistic simulation of tribochemical interactions was conducted to derive a friction model based on the thin-film lubrication theory. This investigation indicates the potential to substantially reduce friction and wear using this fluid in real technical applications.
| S-EPMC6645003 | biostudies-literature
Project description:Fluids are pervasive in fault zones cutting the Earth's crust; however, the effect of fluid viscosity on fault mechanics is mainly conjectured by theoretical models. We present friction experiments performed on both dry and fluid-permeated silicate and carbonate bearing-rocks, at normal effective stresses up to 20 MPa, with a slip-rate ranging between 10 μm/s and 1 m/s. Four different fluid viscosities were tested. We show that both static and dynamic friction coefficients decrease with viscosity and that dynamic friction depends on the dimensionless Sommerfeld number (S) as predicted by the elastohydrodynamic-lubrication theory (EHD).Under favourable conditions (depending on the fluid viscosity (η), co-seismic slip-rate (V), fault geometry (L/H02) and earthquake nucleation depth (∝σeff)), EHD might be an effective weakening mechanism during natural and induced earthquakes. However, at seismic slip-rate, the slip weakening distance (Dc) increases markedly for a range of fluid viscosities expected in the Earth, potentially favouring slow-slip rather than rupture propagation for small to moderate earthquakes.
| S-EPMC6426875 | biostudies-literature
Project description:Synovial joints are the lubricated connections between the bones of our body that are commonly affected in arthritis. It is assumed that synovial joints first evolved as vertebrates came to land, with ray-finned fishes lacking lubricated joints. Here, we examine the expression and function of a critical lubricating protein of mammalian synovial joints, Prg4/Lubricin, in diverse ray-finned fishes. We find that Prg4 homologs are specifically enriched at the jaw and pectoral fin joints of zebrafish, stickleback, and gar, with genetic deletion of the zebrafish prg4b gene resulting in the same age-related degeneration of joints as seen in lubricin-deficient mice and humans. Our data support lubricated synovial joints evolving much earlier than currently accepted, at least in the common ancestor of all bony vertebrates. Establishment of the first arthritis model in the highly regenerative zebrafish will offer unique opportunities to understand the aetiology and possible treatment of synovial joint disease.
| S-EPMC4951194 | biostudies-literature
Project description:Limited surface lubrication and bacterial biofilm formation pose great challenges to biomedical implants. Although hydrophilic lubricated coatings and bacterial resistance coatings have been reported, the harsh and tedious synthesis greatly compromises their application, and more importantly, the bacterial resistance property has seldom been investigated in combination with the lubrication property. In this study, bioinspired by the performances of mussel and articular cartilage, we successfully synthesized self-adhesive lubricated coating and simultaneously achieved optimal lubrication and bacterial resistance properties. Additionally, we reported the mechanism of bacterial resistance on the nanoscale by studying the adhesion interactions between biomimetic coating and hydrophilic/hydrophobic tip or living bacteria via atomic force microscopy. In summary, the self-adhesive lubricated coating can effectively enhance lubrication and bacterial resistance performances based on hydration lubrication and hydration repulsion, and represent a universal and facial strategy for surface functionalization of biomedical implants.
| S-EPMC7868611 | biostudies-literature
Project description:Understanding how an adaptive integrated interface between lubricant additives and solid contacts works will enable improving the wear and friction of moving engine components. This work represents the comprehensive characterization of compositional and structural orientation at the sliding interface from the perspective of surface/interface tribochemistry. The integrated interface of a lubricant additive-solid resulting from the friction testing of Graphite-like carbon (GLC) and PVD-CrN coated rings sliding against cast iron under boundary lubrication was studied. The results indicate that in the case of the CrN/cast iron pair the antiwear and friction behavior were very strongly dependent upon lubricant. In contrast, the tribology of the GLC surface showed a much lower dependence on lubrication. In order to identify the compounds and their distribution across the interface, x-ray microanalysis phase mapping was innovatively applied and the principle of hard and soft acids and bases (HSAB) to understand the behaviour. Phase mapping clearly showed the hierarchical interface of the zinc-iron polyphosphate tribofilm for various sliding pairs and different sliding durations. This interface structure formed between lubricant additives and the sliding surfaces adapts to the sliding conditions - the term adaptive interface. The current results help explain the tribology of these sliding components in engine.
| S-EPMC5577201 | biostudies-literature
Project description:Icephobic coatings interest various industries facing icing problems. However, their durability represents a current limitation in real applications. Therefore, understanding the degradation of coatings under various environmental stresses is necessary for further coating development. Here, lubricated icephobic coatings were fabricated using a flame spray method with hybrid feedstock injection. Low-density polyethylene represented the main coating component. Two additives, namely fully hydrogenated cottonseed oil and paraffinic wax, were added to the coating structure to enhance coating icephobicity. Coating properties were characterised, including topography, surface roughness, thermal properties, wettability, and icephobicity. Moreover, their performance was investigated under various environmental stresses, such as repeated icing/deicing cycles, immersion in corrosive media, and exposure to ultraviolet (UV) irradiation. According to the results, all coatings exhibited medium-low ice adhesion, with slightly more stable icephobic behaviour for cottonseed oil-based coatings over the icing/deicing cycles. Surface roughness slightly increased, and wetting performances decreased after the cyclic tests, but chemical changes were not revealed. Moreover, coatings demonstrated good chemical resistance in selected corrosive media, with better performance for paraffin-based coatings. However, a slight decrease in hydrophobicity was detected due to surface structural changes. Finally, paraffin-based coatings showed better resistance under UV irradiation based on carbonyl index and colour change measurements.
| S-EPMC8779144 | biostudies-literature
Project description:A stone thrown in a lake captures air as it collides with water and sinks; likewise a rain drop falling on a flat surface traps air bubbles underneath and creates a spectacular splash. These natural occurrences, from bubble entrapment to liquid ejection, happen as air fails to escape from the closing gap between liquid and solid surfaces. Trapping of air is devastating for casting, coating, painting, and printing industries, or those intolerant of water entry noise. Attempts to eliminate the interfering air rely on either reducing the ambient pressure or modifying the solid surfaces. The former approach is inflexible in its implementation, while the latter one is inherently limited by the wetting speed of liquid or the draining capacity of air passages created on the solid. Here, we present a "divide and conquer" approach to split the thin air gap into tunnels and subsequently squeeze air out from the tunnels against its viscous resistance using spatially periodic dielectrophoretic force. We confirm the working principles by demonstrating suppression of both bubble entrapment and splash upon impacts of droplets on solid surfaces.
| S-EPMC8277893 | biostudies-literature
Project description:The sliding of a solid object on a solid substrate requires a shear force that is larger than the maximum static friction force. It is commonly believed that the maximum static friction force is proportional to the loading force and does not depend on the apparent contact area. The ratio of the maximum static friction force to the loading force is called the static friction coefficient µM, which is considered to be a constant. Here, we conduct experiments demonstrating that the static friction force of a slider on a substrate follows a novel friction law under certain conditions. The magnitude of µM decreases as the loading force increases or as the apparent contact area decreases. This behavior is caused by the slip of local precursors before the onset of bulk sliding and is consistent with recent theory. The results of this study will develop novel methods for static friction control.
| S-EPMC4159624 | biostudies-literature
Project description:Nowadays, the Colebrook equation is used as a mostly accepted relation for the calculation of fluid flow friction factor. However, the Colebrook equation is implicit with respect to the friction factor (?). In the present study, a noniterative approach using Artificial Neural Network (ANN) was developed to calculate the friction factor. To configure the ANN model, the input parameters of the Reynolds Number (Re) and the relative roughness of pipe (?/D) were transformed to logarithmic scales. The 90,000 sets of data were fed to the ANN model involving three layers: input, hidden, and output layers with, 2, 50, and 1 neurons, respectively. This configuration was capable of predicting the values of friction factor in the Colebrook equation for any given values of the Reynolds number (Re) and the relative roughness (?/D) ranging between 5000 and 10(8) and between 10(-7) and 0.1, respectively. The proposed ANN demonstrates the relative error up to 0.07% which had the high accuracy compared with the vast majority of the precise explicit approximations of the Colebrook equation.
| S-EPMC4834174 | biostudies-literature
Project description:In the last decade, the friction stir welding of polymers has been increasingly investigated by the means of more and more sophisticated approaches. Since the early studies, which were aimed at proving the feasibility of the process for polymers and identifying suitable processing windows, great improvements have been achieved. This owes to the increasing care of academic researchers and industrial demands. These improvements have their roots in the promising results from pioneer studies; however, they are also the fruits of the adoption of more comprehensive approaches and the multidisciplinary analyses of results. The introduction of instrumented machines has enabled the online measurement of processing loads and temperature, and critical understanding of the principal aspects affecting the material flow and welds quality. Such improvements are also clearly demonstrated by the increase of the strength of recent joints (up to 99% of joining efficiency) as compared to those reached in early researches (almost 47%). This article provides a comprehensive review of the recent progresses on the process fundamentals, quality assessment and the influence of process parameters on the mechanical behavior. In addition, emphasis is given to new developments and future perspectives.
| S-EPMC7288317 | biostudies-literature