Negative friction coefficient in microscale graphite/mica layered heterojunctions.
Ontology highlight
ABSTRACT:
SUBMITTER: Liu B
PROVIDER: S-EPMC7164938 | biostudies-literature |
REPOSITORIES: biostudies-literature
Similar Datasets
Project description:Wear-free sliding between two contacted solid surfaces is the ultimate goal in the effort to extend the lifetime of mechanical devices, especially when it comes to inventing new types of micro-electromechanical systems where wear is often a major obstacle. Here we report experimental observations of wear-free sliding for a micrometer-sized graphite flake on a diamond-like-carbon (DLC) surface under ambient conditions with speeds up to 2.5 m/s, and over a distance of 100 km. The coefficient of friction (COF) between the microscale graphite flake, a van der Waals (vdW) layered material and DLC, a non-vdW-layered material, is measured to be of the order of [Formula: see text], which belongs to the superlubric regime. Such ultra-low COFs are also demonstrated for a microscale graphite flake sliding on six other kinds of non-vdW-layered materials with sub-nanometer roughness. With a synergistic analysis approach, we reveal the underlying mechanism to be the combination of interfacial vdW interaction, atomic-smooth interfaces and the low normal stiffness of the graphite flake. These features guarantee a persistent full contact of the interface with weak interaction, which contributes to the ultra-low COFs. Together with the extremely high in-plane strength of graphene, wear-free sliding is achieved. Our results broaden the scope of superlubricity and promote its wider application in the future.
| S-EPMC8776547 | biostudies-literature
Project description:The current-carrying friction characteristics are crucial for the performance of a sliding electrical contact, which plays critical roles in numerous electrical machines and devices. However, these characteristics are influenced by multiple factors such as material surface quality, chemical reactions, and atmospheric environment, leading to a challenge for researchers to comprehensively consider these impacts. Structural superlubricity (SSL), a state of nearly zero friction and no wear between contact solid surfaces, provides an ideal experimental system for these studies. Here, with microscale graphite flakes on atomic-flattened Au surface under applied voltages, we observed two opposite friction phenomena, depending only on whether the edge of graphite flake was in contact with the Au substrate. When in contact the friction force would increase with an increasing voltage, otherwise, the friction force would decrease. Notably, when the voltage was turned off, the friction force quickly recovered to its original level, indicating the absence of wear. Through atmosphere control and molecular dynamics simulations, we revealed the mechanism to be the different roles played by the water molecules confined at the interface or adsorbed near the edges. Our experimental results demonstrate the remarkable tunable and robust frictional properties of SSL under an electrical field, providing an ideal system for the fundamental research of not only sliding electrical contacts, but also novel devices which demand tunable frictions.
| S-EPMC11321252 | biostudies-literature
Project description:Utilizing colloidal probe, lateral force microscopy and simultaneous confocal microscopy, combined with finite element analysis, we investigate how a microparticle starts moving laterally on a soft, adhesive surface. We find that the surface can form a self-contacting crease at the leading front, which results from a buildup of compressive stress. Experimentally, creases are observed on substrates that exhibit either high or low adhesion when measured in the normal direction, motivating the use of simulations to consider the role of adhesion energy and interfacial strength. Our simulations illustrate that the interfacial strength plays a dominating role in the nucleation of a crease. After the crease forms, it progresses through the contact zone in a Schallamach wave-like fashion. Interestingly, our results suggest that this Schallamach wave-like motion is facilitated by free slip at the adhesive, self-contacting interface within the crease.
| S-EPMC10126204 | biostudies-literature
Project description:Friction between dielectric surfaces produces patterns of fixed, stable electric charges that in turn contribute electrostatic components to surface interactions between the contacting solids. The literature presents a wealth of information on the electronic contributions to friction in metals and semiconductors but the effect of triboelectricity on friction coefficients of dielectrics is as yet poorly defined and understood. In this work, friction coefficients were measured on tribocharged polytetrafluoroethylene (PTFE), using three different techniques. As a result, friction coefficients at the macro- and nanoscales increase many-fold when PTFE surfaces are tribocharged, but this effect is eliminated by silanization of glass spheres rolling on PTFE. In conclusion, tribocharging may supersede all other contributions to macro- and nanoscale friction coefficients in PTFE and probably in other insulating polymers.
| S-EPMC3740278 | biostudies-literature
Project description:The correlation between the mechanical properties of Fillers/Epoxy composites and their tribological behavior was investigated. Tensile, hardness, wear, and friction tests were conducted for Neat Epoxy (NE), Graphite/Epoxy composites (GE), and Data Palm Fiber/Epoxy with or without Graphite composites (GFE and FE). The correlation was made between the tensile strength, the modulus of elasticity, elongation at the break, and the hardness, as an individual or a combined factor, with the specific wear rate (SWR) and coefficient of friction (COF) of composites. In general, graphite as an additive to polymeric composite has had an eclectic effect on mechanical properties, whereas it has led to a positive effect on tribological properties, whilst date palm fibers (DPFs), as reinforcement for polymeric composite, promoted a mechanical performance with a slight improvement to the tribological performance. Statistically, this study reveals that there is no strong confirmation of any marked correlation between the mechanical and the specific wear rate of filler/Epoxy composites. There is, however, a remarkable correlation between the mechanical properties and the friction coefficient of filler/Epoxy composites.
| S-EPMC5455661 | biostudies-other
Project description:The friction of graphene on mica was studied using lateral force microscopy. We observed that intercalation of alcohol molecules significantly increases the friction of graphene, as compared to water. An increase of 1.8, 2.4, and 5.9 times in friction between the atomic force microscopy tip and single-layer graphene was observed for methanol, ethanol, and 2-propanol, respectively. Moreover, the friction of graphene is found to be higher for single-layer graphene than for multilayer graphene. We attribute the increase in friction to the additional vibrational modes of alcohol molecules. The significant variation of the frictional characteristics of graphene at the nanoscale by altering the intercalant could open up applications for the next-generation nanolubricants and nanodevices.
| S-EPMC6459005 | biostudies-literature
Project description:Friction is a ubiquitous phenomenon that greatly affects our everyday lives and is responsible for large amounts of energy loss in industrialised societies. Layered materials such as graphene have interesting frictional properties and are often used as (additives to) lubricants to reduce friction and protect against wear. Experimental Atomic Force Microscopy studies and detailed simulations have shown a number of intriguing effects such as frictional strengthening and dependence of friction on the number of layers covering a surface. Here, we propose a simple, fundamental, model for friction on thin sheets. We use our model to explain a variety of seemingly contradictory experimental as well as numerical results. This model can serve as a basis for understanding friction on thin sheets, and opens up new possibilities for ultimately controlling their friction and wear protection.
| S-EPMC6972962 | biostudies-literature
Project description:Traction testing of footwear is expensive, which may create barriers for certain users to assess footwear. This study aimed to develop a statistical model that predicts available coefficient of friction (ACOF) under boundary lubrication conditions based on inexpensive measurements of footwear outsole features. Geometric and material hardness parameters were measured from fifty-eight footwear designs labeled as slip-resistant. A robotic friction measurement device was used to quantify ACOF with canola oil as the contaminant. Stepwise regression methods were used to develop models based on the outsole parameters and floor type to predict ACOF. The predictive ability of the regression models was tested using the k-fold cross-validation method. Results indicated that 87% of ACOF variation was explained by three shoe outsole parameters (tread surface area, heel shape, hardness) and floor type. This approach may provide an assessment tool for safety practitioners to assess footwear traction and improve workers' safety.
| S-EPMC7365588 | biostudies-literature
Project description:The origin of ultra-low friction exhibited by heterogeneous junctions of graphene and hexagonal boron nitride (h-BN) is revealed. For aligned interfaces, we identify a characteristic contact size, below which the junction behaves like its homogeneous counterparts with friction forces that grow linearly with the contact area. Superlubricity sets in due to the progressive appearance of Moiré patterns resulting in a collective stick-slip motion of the elevated super-structure ridges that turns into smooth soliton-like gliding with increasing contact size. Incommensurability effects are enhanced in misaligned contacts, where the friction coefficients further drop by orders of magnitude. Our fully atomistic simulations show that the superlubric regime in graphene/h-BN heterostructures persists up to significantly higher loads compared to the well-studied twisted homogeneous graphene interface. This indicates the potential of achieving robust superlubricity in practical applications using two-dimensional layered materials heterojunctions.
| S-EPMC5589749 | biostudies-literature
Project description:This paper investigates the friction coefficient of a moving liquid marble, a small liquid droplet coated with hydrophobic powder and floating on another liquid surface. A floating marble can easily move across water surface due to the low friction, allowing for the transport of aqueous solutions with minimal energy input. However, the motion of a floating marble has yet to be systematically characterised due to the lack of insight into key parameters such as the coefficient of friction between the floating marble and the carrier liquid. We measured the coefficient of friction of a small floating marble using a novel experimental setup that exploits the non-wetting properties of a liquid marble. A floating liquid marble pair containing a minute amount magnetite particles were immobilised and then released in a controlled manner using permanent magnets. The capillarity-driven motion was analysed to determine the coefficient of friction of the liquid marbles. The "capillary charge" model was used to fit the experimental results. We varied the marble content and carrier liquid to establish a relationship between the friction correction factor and the meniscus angle.
| S-EPMC5133567 | biostudies-literature