Dataset Information

Data to support the assessment of the energy efficiency estimation methods on induction motors considering real-time monitoring.

ABSTRACT: The data presented in this article was used to assess and compare the most important methods used to estimate the efficiency during the operation of induction motors at different loads and power supply conditions. The experiment was developed in a test bench including a three-phase induction motor of 1.1 kW (De Lorenzo DL 1021). In addition, an adjustable voltage source, a variable-frequency drive, a resistor, and a magnetic powder brake control unit to regulate the load were used during the experiments. A power quality and energy analyzer (Fluke 435 series 6) was used to measure the electric variables during the experiments. Moreover, for the mechanical measures, the sensors of the brake control unit (De Lorenzo DL 1054TT) and a magnetic powder brake (De Lorenzo DL 1019P) were used. In total, 11 load factors were measured at different operation conditions, including balanced sinusoidal voltage, balanced harmonic voltage, unbalanced sinusoidal voltage and unbalanced harmonic voltage. A total of 10 measures were taken for each load factor at each operation condition. The data presented in this paper can be useful in the development and evaluation of new efficiency estimation methods for induction motors, considering different operation conditions and load factors. Moreover, it can serve to assess the impact of the energy quality on the efficiency of induction motors. The data is related to the manuscript "Assessment of the energy efficiency estimation methods on induction motors considering real-time monitoring" [1].

SUBMITTER: Sousa Santos V

PROVIDER: S-EPMC7186514 | biostudies-literature | 2020 Jun

REPOSITORIES: biostudies-literature

ACCESS DATA

Publications

Data to support the assessment of the energy efficiency estimation methods on induction motors considering real-time monitoring.

Sousa Santos Vladimir V Cabello Eras Juan J JJ Sagastume Gutiérrez Alexis A Cabello Ulloa Mario J MJ

Data in brief 20200423

The data presented in this article was used to assess and compare the most important methods used to estimate the efficiency during the operation of induction motors at different loads and power supply conditions. The experiment was developed in a test bench including a three-phase induction motor of 1.1 kW (De Lorenzo DL 1021). In addition, an adjustable voltage source, a variable-frequency drive, a resistor, and a magnetic powder brake control unit to regulate the load were used during the exp ...[more]

PMID: 32368582

Similar Datasets

Project description:Energy resolving detectors provide more than one spectral measurement in one image acquisition. The purpose of this study is to investigate, with simulation, the ability to decompose four materials using energy discriminating detectors and least squares minimization techniques.Three least squares parameter estimation decomposition techniques were investigated for four-material breast imaging tasks in the image domain. The first technique treats the voxel as if it consisted of fractions of all the materials. The second method assumes that a voxel primarily contains one material and divides the decomposition process into segmentation and quantification tasks. The third is similar to the second method but a calibration was used. The simulated computed tomography (CT) system consisted of an 80 kVp spectrum and a CdZnTe (CZT) detector that could resolve the x-ray spectrum into five energy bins. A postmortem breast specimen was imaged with flat panel CT to provide a model for the digital phantoms. Hydroxyapatite (HA) (50, 150, 250, 350, 450, and 550 mg/ml) and iodine (4, 12, 20, 28, 36, and 44 mg/ml) contrast elements were embedded into the glandular region of the phantoms. Calibration phantoms consisted of a 30/70 glandular-to-adipose tissue ratio with embedded HA (100, 200, 300, 400, and 500 mg/ml) and iodine (5, 15, 25, 35, and 45 mg/ml). The x-ray transport process was simulated where the Beer-Lambert law, Poisson process, and CZT absorption efficiency were applied. Qualitative and quantitative evaluations of the decomposition techniques were performed and compared. The effect of breast size was also investigated.The first technique decomposed iodine adequately but failed for other materials. The second method separated the materials but was unable to quantify the materials. With the addition of a calibration, the third technique provided good separation and quantification of hydroxyapatite, iodine, glandular, and adipose tissues. Quantification with this technique was accurate with errors of 9.83% and 6.61% for HA and iodine, respectively. Calibration at one point (one breast size) showed increased errors as the mismatch in breast diameters between calibration and measurement increased. A four-point calibration successfully decomposed breast diameter spanning the entire range from 8 to 20 cm. For a 14 cm breast, errors were reduced from 5.44% to 1.75% and from 6.17% to 3.27% with the multipoint calibration for HA and iodine, respectively.The results of the simulation study showed that a CT system based on CZT detectors in conjunction with least squares minimization technique can be used to decompose four materials. The calibrated least squares parameter estimation decomposition technique performed the best, separating and accurately quantifying the concentrations of hydroxyapatite and iodine.

Dataset Information

Data to support the assessment of the energy efficiency estimation methods on induction motors considering real-time monitoring.

Publications

Data to support the assessment of the energy efficiency estimation methods on induction motors considering real-time monitoring.

Similar Datasets

OmicsDI is part of the ELIXIR infrastructure

Tweets