Microcavity top-emission perovskite light-emitting diodes.
Ontology highlight
ABSTRACT:
SUBMITTER: Miao Y
PROVIDER: S-EPMC7242415 | biostudies-literature |
REPOSITORIES: biostudies-literature
Similar Datasets
Project description:Reducing environmental impact is a key challenge for perovskite optoelectronics, as most high-performance devices are based on potentially toxic lead-halide perovskites. For photovoltaic solar cells, tin-lead (Sn-Pb) perovskite materials provide a promising solution for reducing toxicity. However, Sn-Pb perovskites typically exhibit low luminescence efficiencies, and are not ideal for light-emitting applications. Here we demonstrate highly luminescent germanium-lead (Ge-Pb) perovskite films with photoluminescence quantum efficiencies (PLQEs) of up to ~71%, showing a considerable relative improvement of ~34% over similarly prepared Ge-free, Pb-based perovskite films. In our initial demonstration of Ge-Pb perovskite LEDs, we achieve external quantum efficiencies (EQEs) of up to ~13.1% at high brightness (~1900 cd m-2), a step forward for reduced-toxicity perovskite LEDs. Our findings offer a new solution for developing eco-friendly light-emitting technologies based on perovskite semiconductors.
| S-EPMC8277869 | biostudies-literature
Project description:Device performance and in particular device stability for blue perovskite light-emitting diodes (PeLEDs) remain considerable challenges for the whole community. In this manuscript, we conceive an approach by tuning the 'A-site' cation composition of perovskites to develop blue-emitters. We herein report a Rubidium-Cesium alloyed, quasi-two-dimensional perovskite and demonstrate its great potential for pure-blue PeLED applications. Composition engineering and in-situ passivation are conducted to further improve the material's emission property and stabilities. Consequently, we get a prominent film photoluminescence quantum yield of around 82% under low excitation density. Encouraged by these findings, we finally achieve a spectra-stable blue PeLED with the peak external quantum efficiency of 1.35% and a half-lifetime of 14.5 min, representing the most efficient and stable pure-blue PeLEDs reported so far. The strategy is also demonstrated to be able to generate efficient perovskite blue emitters and PeLEDs in the whole blue spectral region (from 454 to 492 nm).
| S-EPMC6478869 | biostudies-literature
Project description:Mobile and wearable devices are increasingly reliant on near-infrared (NIR) covert illumination for facial recognition, eye-tracking or motion and depth sensing functions. However, these small devices offer limited spatial real estate that is typically already occupied by their full-area electronic color displays. Here, we report a transparent perovskite light-emitting diode (LED) that could be overlaid across a color display to provide an efficient and high-intensity NIR illumination. Our transparent devices are constructed with an ITO/AZO/PEIE/FAPbI3/poly-TPD/MoO3/Al/ITO/Ag/ITO architecture, and offer a high average transmittance of more than 55% across the visible spectral region. In particular, our Al/ITO/Ag/ITO top transparent electrode was designed to offer a combination low sheet resistance and low plasma damage upon electrode deposition. The devices emit at 799 nm with a high total external quantum efficiency of 5.7% at a current density of 5.3 mA cm-2 and a high radiance of 1.5 W sr-1 m-2, and possess a large functional device area of 120 mm2. The efficient performance is ideal for battery-powered wearable devices, and could enable advanced security and sensing features on future smart-watches, phones, gaming consoles and augmented or virtual reality headsets.
| S-EPMC7445238 | biostudies-literature
Project description:Hybrid perovskite semiconductors represent a promising platform for color-tunable light emitting diodes (LEDs) and lasers; however, the behavior of these materials under the intense electrical excitation required for electrically-pumped lasing remains unexplored. Here, we investigate methylammonium lead iodide-based perovskite LEDs under short pulsed drive at current densities up to 620 A cm-2. At low current density (J < 10 A cm-2), we find that the external quantum efficiency (EQE) depends strongly on the time-averaged history of the pulse train and show that this curiosity is associated with slow ion movement that changes the internal field distribution and trap density in the device. The impact of ions is less pronounced in the high current density regime (J > 10 A cm-2), where EQE roll-off is dominated by a combination of Joule heating and charge imbalance yet shows no evidence of Auger loss, suggesting that operation at kA cm-2 current densities relevant for a laser diode should be within reach.
| S-EPMC6244086 | biostudies-literature
Project description:Solution-processed planar perovskite light-emitting diodes (LEDs) promise high-performance and cost-effective electroluminescent devices ideal for large-area display and lighting applications. Exploiting emission layers with high ratios of horizontal transition dipole moments (TDMs) is expected to boost the photon outcoupling of planar LEDs. However, LEDs based on anisotropic perovskite nanoemitters remain to be inefficient (external quantum efficiency, EQE <5%) due to the difficulties of simultaneously controlling the orientations of TDMs, achieving high photoluminescence quantum yields (PLQYs) and realizing charge balance in the films of assembled nanostructures. Here, we demonstrate efficient electroluminescence from an in situ grown perovskite film composed of a monolayer of face-on oriented nanoplatelets. The ratio of horizontal TDMs of the perovskite nanoplatelet film is ~84%, which leads to a light-outcoupling efficiency of ~31%, substantially higher than that of isotropic emitters (~23%). In consequence, LEDs with a peak EQE of 23.6% are achieved, representing highly efficient planar perovskite LEDs.
| S-EPMC8500509 | biostudies-literature
Project description:Encasing an OLED between two planar metallic electrodes creates a Fabry-Pérot microcavity, resulting in significant narrowing of the emission bandwidth. The emission from such microcavity OLEDs depends on the overlap of the resonant cavity modes and the comparatively broadband electroluminescence spectrum of the organic molecular emitter. Varying the thickness of the microcavity changes the mode structure, resulting in a controlled change in the peak emission wavelength. Employing a silicon wafer substrate with high thermal conductivity to dissipate excess heat in thicker cavities allows cavity thicknesses from 100 to 350 nm to be driven at high current densities. Three resonant modes, the fundamental and first two higher harmonics, are characterized, resulting in tunable emission peaks throughout the visible range with increasingly narrow bandwidth in the higher modes. Angle resolved electroluminescence spectroscopy reveals the outcoupling of the TE and TM waveguide modes which blue-shift with respect to the normal emission at higher angles. Simultaneous stimulation of two resonant modes can produce dual peaks in the violet and red, resulting in purple emission. These microcavity-based OLEDs employ a single green molecular emitter and can be tuned to span the entire color gamut, including both the monochromatic visible range and the purple line.
| S-EPMC8055888 | biostudies-literature
Project description:In this study, we report on the application of a dielectric/ultra-thin metal/dielectric (DMD) multilayer consisting of ytterbium (Yb)-doped molybdenum oxide (MoO3)/silver (Ag)/MoO3 stacked as the transparent cathode in top-emitting green quantum dot light-emitting diodes (QLED). By optimizing the Yb doping ratio, we have highly improved the electron injection ability from 0.01 to 0.35. In addition, the dielectric/ultra-thin metal/dielectric (DMD) cathode also shows a low sheet resistance of only 12.2 ?/sq, which is superior to the resistance of the commercially-available indium tin oxide (ITO) electrode (~15 ?/sq). The DMD multilayer exhibits a maximum transmittance of 75% and an average transmittance of 70% over the visible range of 400-700 nm. The optimized DMD-based G-QLED has a smaller current leakage at low driving voltage. The optimized DMD-based G-QLED enhances the current density than that of G-QLED with indium zinc oxide (IZO) as a cathode. The fabricated DMD-based G-QLED shows a low turn-on voltage of 2.2 V, a high current efficiency of 38 cd/A, and external quantum efficiency of 9.8. These findings support the fabricated DMD multilayer as a promising cathode for transparent top-emitting diodes.
| S-EPMC7221779 | biostudies-literature
Project description:Perovskite light-emitting diodes (PeLEDs) have shown excellent performance in the green and near-infrared spectral regions, with high color purity, efficiency, and brightness. In order to shift the emission wavelength to the blue, compositional engineering (anion mixing) and quantum-confinement engineering (reduced-dimensionality) have been employed. Unfortunately, LED emission profiles shift with increasing driving voltages due to either phase separation or the coexistence of multiple crystal domains. Here we report color-stable sky-blue PeLEDs achieved by enhancing the phase monodispersity of quasi-2D perovskite thin films. We selected cation combinations that modulate the crystallization and layer thickness distribution of the domains. The perovskite films show a record photoluminescence quantum yield of 88% at 477?nm. The corresponding PeLEDs exhibit stable sky-blue emission under high operation voltages. A maximum luminance of 2480?cd?m-2 at 490?nm is achieved, fully one order of magnitude higher than the previous record for quasi-2D blue PeLEDs.
| S-EPMC6117319 | biostudies-literature
Project description:Serious performance decline arose for perovskite light-emitting diodes (PeLEDs) once the active area was enlarged. Here we investigate the failure mechanism of the widespread active film fabrication method; and ascribe severe phase-segregation to be the reason. We thereby introduce L-Norvaline to construct a COO--coordinated intermediate phase with low formation enthalpy. The new intermediate phase changes the crystallization pathway, thereby suppressing the phase-segregation. Accordingly, high-quality large-area quasi-2D films with desirable properties are obtained. Based on this, we further rationally adjusted films' recombination kinetics. We reported a series of highly-efficient green quasi-2D PeLEDs with active areas of 9.0 cm2. The peak EQE of 16.4% is achieved in <n > = 3, represent the most efficient large-area PeLEDs yet. Meanwhile, high brightness device with luminance up to 9.1 × 104 cd m-2 has achieved in <n> = 10 film.
| S-EPMC8044177 | biostudies-literature
Project description:Perovskite light-emitting diodes have recently broken the 20% barrier for external quantum efficiency. These values cannot be explained with classical models for optical outcoupling. Here, we analyse the role of photon recycling (PR) in assisting light extraction from perovskite light-emitting diodes. Spatially-resolved photoluminescence and electroluminescence measurements combined with optical modelling show that repetitive re-absorption and re-emission of photons trapped in substrate and waveguide modes significantly enhance light extraction when the radiation efficiency is sufficiently high. In this manner, PR can contribute more than 70% to the overall emission, in agreement with recently-reported high efficiencies. While an outcoupling efficiency of 100% is theoretically possible with PR, parasitic absorption losses due to absorption from the electrodes are shown to limit practical efficiencies in current device architectures. To overcome the present limits, we propose a future configuration with a reduced injection electrode area to drive the efficiency toward 100%.
| S-EPMC6992794 | biostudies-literature