Dataset Information

Analysis of Tillage Depth and Gear Selection for Mechanical Load and Fuel Efficiency of an Agricultural Tractor Using an Agricultural Field Measuring System.

ABSTRACT: This study was conducted to analyze the effects of tillage depth and gear selection on the mechanical load and fuel efficiency of an agricultural tractor during plow tillage. In order to analyze these effects, we developed an agricultural field measuring system consisting of a load measurement part (wheel torque meter, proximity sensor, and real-time kinematic (RTK) global positioning system (GPS)) and a tillage depth measurement part (linear potentiometer and inclinometer). Field tests were carried out using moldboard plows with a maximum tillage depth of 20 cm and three gear selections (M2H, M3L, and M3H) in a rice stubble paddy field for plow tillage. The average travel speed and slip ratio had the lowest M2H and the highest M3L. M3H had the highest theoretical speed, but the travel speed was 0.13 km/h lower than M3L due to the reduction in the axle rotational speed at deep tillage depth. Regarding engine load, the higher the gear, the greater the torque and the lower the axle rotation speed. The front axle load was not significantly affected by the tillage depth as compared to other mechanical parts, except for the M3H gear. The rear axle load generated about twice the torque of the front wheel and overall, it tended to show a higher average rear axle torque at higher gear selection. The rear axle load and fuel rate were found to be most affected by the combination of the tillage depth and gear selection combination. Overall, field test results show that the M3H had the highest fuel efficiency and a high working speed while overcoming high loads at the same tillage depth. In conclusion, M3H is the most suitable gear stage for plow cultivation, and the higher the gear stage and the deeper the tillage depth during plowing, the higher the fuel efficiency. The results of this study will be useful for analyzing mechanical load and fuel efficiency during farm operations. In a future study, we will conduct load analysis studies in other farming operations that consider various soil mechanics factors as well as tillage depths and gear selections.

SUBMITTER: Kim YS

PROVIDER: S-EPMC7249661 | biostudies-literature | 2020 Apr

REPOSITORIES: biostudies-literature

ACCESS DATA

Publications

Analysis of Tillage Depth and Gear Selection for Mechanical Load and Fuel Efficiency of an Agricultural Tractor Using an Agricultural Field Measuring System.

Kim Yeon-Soo YS Kim Wan-Soo WS Baek Seung-Yun SY Baek Seung-Min SM Kim Young-Joo YJ Lee Sang-Dae SD Kim Yong-Joo YJ

Sensors (Basel, Switzerland) 20200426 9

This study was conducted to analyze the effects of tillage depth and gear selection on the mechanical load and fuel efficiency of an agricultural tractor during plow tillage. In order to analyze these effects, we developed an agricultural field measuring system consisting of a load measurement part (wheel torque meter, proximity sensor, and real-time kinematic (RTK) global positioning system (GPS)) and a tillage depth measurement part (linear potentiometer and inclinometer). Field tests were car ...[more]

PMID: 32357392

Similar Datasets

Project description:The objectives of this study were to develop a real-time tillage depth measurement system for agricultural tractor performance analysis and then to validate these configured systems through soil non-penetration tests and field experiment during plow tillage. The real-time tillage depth measurement system was developed by using a sensor fusion method, consisting of a linear potentiometer, inclinometer, and optical distance sensor to measure the vertical penetration depth of the attached implement. In addition, a draft force measurement system was developed using six-component load cells, and an accuracy of 98.9% was verified through a static load test. As a result of the soil non-penetration tests, it was confirmed that sensor fusion type A, consisting of a linear potentiometer and inclinometer, was 6.34-11.76% more accurate than sensor fusion type B, consisting of an optical distance sensor and inclinometer. Therefore, sensor fusion type A was used during field testing as it was found to be more suitable for use in severe working environments. To verify the accuracy of the real-time tillage depth measurement system, a linear regression analysis was performed between the measured draft and the predicted values calculated using the American Society of Agricultural and Biological Engineers (ASABE) standards-based equation. Experimental data such as traveling speed and draft force showed that it was significantly affected by tillage depth, and the coefficient of determination value at M3-Low was 0.847, which is relatively higher than M3-High. In addition, the regression analysis of the integrated data showed an R-square value of 0.715, which is an improvement compared to the accuracy of the ASABE standard prediction formula. In conclusion, the effect of tillage depth on draft force of agricultural tractors during plow tillage was analyzed by the simultaneous operation of the proposed real-time tillage depth measurement system and draft force measurement system. In addition, system accuracy is higher than the predicted accuracy of ±40% based on the ASABE standard equation, which is considered to be useful for various agricultural machinery research fields. In future studies, real-time tillage depth measurement systems can be used in tractor power train design and to ensure component reliability, in accordance with agricultural working conditions, by predicting draft force and axle loads depending on the tillage depth during tillage operations.

Project description:Discomfort during load carriage is a major issue for activities using backpacks (e.g. infantry maneuvers, children carrying school supplies, or outdoor sports). It is currently unclear which mechanical parameters are responsible for subjectively perceived discomfort. The aim of this study was to identify objectively measured mechanical predictors of discomfort during load carriage. We compared twelve different configurations of a typical load carriage system, a commercially available backpack with a hip belt. The pressure distribution under the hip belt and the shoulder strap, as well as the tensile force in the strap and the relative motion of the backpack were measured. Multiple linear regression analyses were conducted to investigate possible predictors of discomfort. The results demonstrate that static peak pressure, or alternatively, static strap force is a significant (p<0.001) predictor of discomfort during load carriage in the shoulder and hip region, accounting for 85% or more of the variation in discomfort. As an additional finding, we discovered that the regression coefficients of these predictors are significantly smaller for the hip than for the shoulder region. As static peak pressure is measured directly on the body, it is less dependent on the type of load carriage system than static strap force. Therefore, static peak pressure is well suited as a generally applicable, objective mechanical parameter for the optimization of load carriage system design. Alternatively, when limited to load carriage systems of the type backpack with hip belt, static strap force is the most valuable predictor of discomfort. The regionally differing regression coefficients of both predictors imply that the hip region is significantly more tolerant than the shoulder region. In order to minimize discomfort, users should be encouraged to shift load from the shoulders to the hip region wherever possible, at the same time likely decreasing the risk of low back pain or injury.

Dataset Information

Analysis of Tillage Depth and Gear Selection for Mechanical Load and Fuel Efficiency of an Agricultural Tractor Using an Agricultural Field Measuring System.

Publications

Analysis of Tillage Depth and Gear Selection for Mechanical Load and Fuel Efficiency of an Agricultural Tractor Using an Agricultural Field Measuring System.

Similar Datasets

OmicsDI is part of the ELIXIR infrastructure

Tweets