Dataset Information

Temperature and Driving Cycle Significantly Affect Carbonaceous Gas and Particle Matter Emissions from Diesel Trucks.

ABSTRACT: The present study examines the effects of fuel [an ultralow sulfur diesel (ULSD) versus a 20% v/v soy-based biodiesel-80% v/v petroleum blend (B20)], temperature, load, vehicle, driving cycle, and active regeneration technology on gas- and particle-phase carbon emissions from light and medium heavy-duty diesel vehicles (L/MHDDV). The study is performed using chassis dynamometer facilities that support low-temperature operation (-6.7 °C versus 21.7 °C) and heavy loads up to 12 000 kg. Organic and elemental carbon (OC-EC) composition of aerosol particles is determined using a thermal-optical technique. Gas- and particle-phase semivolatile organic compound (SVOC) emissions collected using traditional filter and polyurethane foam sampling media are analyzed using advanced gas chromatograpy/mass spectrometry methods. Study-wide OC and EC emissions are 0.735 and 0.733 mg/km, on average. The emissions factors for diesel vehicles vary widely, and use of a catalyzed diesel particle filter (CDPF) device generally mutes the carbon particle emissions in the exhaust, which contains ~90% w/w gas-phase matter. Interestingly, replacing ULSD with B20 did not significantly influence SVOC emissions, for which sums range from 0.030 to 9.4 mg/km for the L/MHDDVs. However, both low temperature and vehicle cold-starts significantly increase SVOCs in the exhaust. Real-time particle measurements indicate vehicle regeneration technology did influence emissions, although regeneration effects went unresolved using bulk chemistry techniques. A multistudy comparison of the toxic particle-phase polycyclic aromatic hydrocarbons (PAHs; molecular weight (MW) ? 252 amu) in diesel exhaust indicates emission factors that span up to 8 orders of magnitude over the past several decades. This study observes conditions under which PAH compounds with MW ? 252 amu appear in diesel particles downstream of the CDPF and can even reach low-end concentrations reported earlier for much larger HDDVs with poorly controlled exhaust streams. This rare observation suggests that analysis of PAHs in particles emitted from modern L/MHDDVs may be more complex than recognized previously.

SUBMITTER: Hays MD

PROVIDER: S-EPMC7252512 | biostudies-literature | 2017 Sep

REPOSITORIES: biostudies-literature

ACCESS DATA

Publications

Temperature and Driving Cycle Significantly Affect Carbonaceous Gas and Particle Matter Emissions from Diesel Trucks.

Hays Michael D MD Preston William W George Barbara J BJ George Ingrid J IJ Snow Richard R Faircloth James J Long Thomas T Baldauf Richard W RW McDonald Joseph J

Energy & fuels : an American Chemical Society journal 20170901 10

The present study examines the effects of fuel [an ultralow sulfur diesel (ULSD) versus a 20% v/v soy-based biodiesel-80% v/v petroleum blend (B20)], temperature, load, vehicle, driving cycle, and active regeneration technology on gas- and particle-phase carbon emissions from light and medium heavy-duty diesel vehicles (L/MHDDV). The study is performed using chassis dynamometer facilities that support low-temperature operation (-6.7 °C versus 21.7 °C) and heavy loads up to 12 000 kg. Organic and ...[more]

PMID: 32461712

Similar Datasets

Project description:Biodiesel is regarded by many as a "greener" alternative fuel to petroleum diesel with potentially lower health risk. However, recent studies examining biodiesel particulate matter (PM) characteristics and health effects are contradictive, and typically utilize PM generated by passenger car engines in laboratory settings. There is a critical need to analyze diesel and biodiesel PM generated in a "real-world" setting where heavy duty-diesel (HDD) engines and commercially purchased fuel are utilized. This study compares the mass concentrations, chemical composition and cytotoxicity of real-world PM from combustion of both petroleum diesel and a waste grease 20% biodiesel blend (B20) at a community recycling center operating HDD nonroad equipment. PM was analyzed for metals, elemental/organic carbon (EC/OC), polycyclic aromatic hydrocarbons (PAHs), and nitro-polycyclic aromatic hydrocarbons (N-PAHs). Cytotoxicity in a human lung epithelial cell line (BEAS-2B) following 24h exposure to the real-world particles was also evaluated. On average, higher concentrations for both EC and OC were measured in diesel PM. B20 PM contained significantly higher levels of Cu and Mo whereas diesel PM contained significantly higher concentrations of Pb. Principal component analysis determined Mo, Cu, and Ni were the metals with the greatest loading factor, suggesting a unique pattern related to the B20 fuel source. Total PAH concentration during diesel fuel use was 1.9 times higher than during B20 operations; however, total N-PAH concentration was 3.3 times higher during B20 use. Diesel PM cytotoxicity was 8.5 times higher than B20 PM (p<0.05) in a BEAS-2B cell line. This study contributes novel data on real-world, nonroad engine sources of metals, PAH and N-PAH species, comparing tailpipe PM vs. PM collected inside the equipment cabin. Results suggest PM generated from burning petroleum diesel in nonroad engines may be more harmful to human health, but the links between exposure, composition and toxicity are not straightforward.

Project description:Biomass pellets are emerging as a cleaner alternative to traditional biomass fuels. The potential benefits of using biomass pellets include improving energy utilization efficiency and reducing emissions of air pollutants. To assess the environmental, climate, and health significance of replacing traditional fuels with biomass pellets, it is critical to measure the emission factors (EFs) of various pollutants from pellet burning. However, only a few field measurements have been conducted on the emissions of carbon monoxide (CO), particulate matter (PM), and polycyclic aromatic hydrocarbons (PAHs) from the combustion of pellets. In this study, pine wood and corn straw pellets were burned in a pellet burner (2.6 kW), and the EFs of CO, organic carbon, elemental carbon, PM, and PAHs (EF(CO), EF(OC), EF(EC), EF(PM), and EF(PAH)) were determined. The average EF(CO), EF(OC), EF(EC), and EF(PM) were 1520 ± 1170, 8.68 ± 11.4, 11.2 ± 8.7, and 188 ± 87 mg/MJ for corn straw pellets and 266 ± 137, 5.74 ± 7.17, 2.02 ± 1.57, and 71.0 ± 54.0 mg/MJ for pine wood pellets, respectively. Total carbonaceous carbon constituted 8 to 14% of the PM mass emitted. The measured values of EF(PAH) for the two pellets were 1.02 ± 0.64 and 0.506 ± 0.360 mg/MJ, respectively. The secondary side air supply in the pellet burner did not change the EFs of most pollutants significantly (p > 0.05). The only exceptions were EF(OC) and EF(PM) for pine wood pellets because of reduced combustion temperatures with the increased air supply. In comparison with EFs for the raw pine wood and corn straw, EF(CO), EF(OC), EF(EC), and EF(PM) for pellets were significantly lower than those for raw fuels (p < 0.05). However, the differences in EF(PAH) were not significant (p > 0.05). Based on the measured EFs and thermal efficiencies, it was estimated that 95, 98, 98, 88, and 71% reductions in the total emissions of CO, OC, EC, PM, and PAHs could be achieved by replacing the raw biomass fuels combusted in traditional cooking stoves with pellets burned in modern pellet burners.

Dataset Information

Temperature and Driving Cycle Significantly Affect Carbonaceous Gas and Particle Matter Emissions from Diesel Trucks.

Publications

Temperature and Driving Cycle Significantly Affect Carbonaceous Gas and Particle Matter Emissions from Diesel Trucks.

Similar Datasets

OmicsDI is part of the ELIXIR infrastructure