Browse
Submit Data
Databases
API
Help

Dataset Information

14 Views

0 Connections

0 Citations

0 Reanalyses

0 Downloads

Omics score: 0

Large-scale wet-spinning of highly electroconductive MXene fibers.

ABSTRACT: Ti₃C₂T_x MXene is an emerging class of two-dimensional nanomaterials with exceptional electroconductivity and electrochemical properties, and is promising in the manufacturing of multifunctional macroscopic materials and nanomaterials. Herein, we develop a straightforward, continuously controlled, additive/binder-free method to fabricate pure MXene fibers via a large-scale wet-spinning assembly. Our MXene sheets (with an average lateral size of 5.11 μm²) are highly concentrated in water and do not form aggregates or undergo phase separation. Introducing ammonium ions during the coagulation process successfully assembles MXene sheets into flexible, meter-long fibers with very high electrical conductivity (7,713 S cm^-1). The fabricated MXene fibers are comprehensively integrated by using them in electrical wires to switch on a light-emitting diode light and transmit electrical signals to earphones to demonstrate their application in electrical devices. Our wet-spinning strategy provides an approach for continuous mass production of MXene fibers for high-performance, next-generation, and wearable electronic devices.

SUBMITTER: Eom W

PROVIDER: S-EPMC7272396 | biostudies-literature |

REPOSITORIES: biostudies-literature

ACCESS DATA

Json Xml

Similar Datasets

Fabrication of κ-Carrageenan Fibers by Wet Spinning: Spinning Parameters.

Project description:This study demonstrates the fabrication of κ-carrageenan fibers by a wet-spinning method and discusses three important spinning parameters: coagulation bath composition, spinning rate and post-spinning mechanical drawing. The as-spun fiber diameter decreased with KCl and ethanol concentration in the coagulation bath. In general, the ultimate tensile stress and elongation at break both increased for KCl concentration from 0.1 to 0.5 M with and without ethanol, with no significant change above 0.5 M. Spinning rate affected the dope flow and thus the polymer orientation (apparent viscosity) and fiber morphology. At spinning rates between 0.25 mL/min and 0.33 mL/min, the fiber diameter reached a minimum and the fiber surface was smooth. Both an increase and decrease from this spinning rate range increased the fiber diameter and roughness of the fiber surface. Post-spinning drawing of the fiber resulted in even smaller fiber diameter.

| S-EPMC5448880 | biostudies-other

Wet-spinning assembly of continuous, neat, and macroscopic graphene fibers.

Project description:Graphene is now the most attractive carbon-based material. Integration of 2D graphene sheets into macroscopic architectures such as fibers illuminates the direction to translate the excellent properties of individual graphene into advanced hierarchical ensembles for promising applications in new graphene-based nanodevices. However, the lack of effective, low-cost and convenient assembly strategy has blocked its further development. Herein, we demonstrate that neat and macroscopic graphene fibers with high mechanical strength and electrical conductivity can be fluidly spun from the common graphene oxide (GO) suspensions in large scale followed with chemical reduction. The curliness-fold formation mechanism of GO fiber has been proposed. This wet-spinning technique presented here facilitates the multifunctionalization of macroscopic graphene-based fibers with various organic or inorganic components by an easy-handle in situ or post-synthesis approach, which builds the solid foundation to access a new family of advanced composite materials for the next practical applications.

| S-EPMC3430881 | biostudies-other

Wet-spinning of PEDOT:PSS/functionalized-SWNTs composite: a facile route toward production of strong and highly conducting multifunctional fibers.

Project description:With the aim of fabricating multifunctional fibers with enhanced mechanical properties, electrical conductivity and electrochemical performance, we develop wet-spinning of composite formulation based on functionalized PEG-SWNT and PEDOT:PSS. The method of addition and loading are directly correlated to the quality and the ease of spinnability of the formulation and to the mechanical and electrical properties of the resultant fibers. Both the fiber modulus (Y) and strength (?) scaled linearly with PEG-SWNT volume fraction (Vf). A remarkable reinforcement rate of dY/dVf = 417?GPa and d?/dVf = 4?GPa were obtained when PEG-SWNTs at Vf ? 0.02. Further increase of PEG-SWNTs loading (i.e. up to Vf 0.12) resulted in further enhancements up to 22.8?GPa and 254?MPa in Modulus and ultimate stress, respectively. We also show the enhancement of electrochemical supercapacitor performance of composite fibers. These outstanding mechanical, electrical and electrochemical performances place these fibers among the best performing multifunctional composite fibers.

| S-EPMC3863815 | biostudies-other

Some Specifics of Defect-Free Poly-(o-aminophenylene)naphthoylenimide Fibers Preparation by Wet Spinning.

Project description:A series of model experiments were carried out on drops of poly-(o-aminophenylene)naphthoylenimide (PANI-O) solutions in N-methyl-2-pyrrolidone (NMP) surrounded by a coagulant of different compositions as starting points of defect-free fibers spinning by the wet method. An influence of compositions of dopes and multicomponent coagulants on the diffusion kinetics and drop morphology during coagulation has been investigated. It is shown that the defining parameters of the coagulation process are viscoelastic properties of the polymer solution and the diffusion activity of the coagulant, meaning not only the rate of coagulation but also the presence/absence of macro defects in the resulting fiber. The optimal morphology of as-spun fibers is obtained by coagulation of solution in a three-component mixture containing solvent and two precipitants of different activity (water and ethanol). The chosen coagulating mixture was used for the fiber spinning of PANI-O with different molecular weights dopes, and fibers with sufficiently high strength (~250 MPa), moduli (~2.1 MPa), and elongation at break (50%) were obtained.

| S-EPMC8836713 | biostudies-literature

Wet-Spun Chitosan-Sodium Caseinate Fibers for Biomedicine: From Spinning Process to Physical Properties.

Project description:We designed and characterized chitosan-caseinate fibers processed through wet spinning for biomedical applications such as drug delivery from knitted medical devices. Sodium caseinate was either incorporated directly into the chitosan dope or allowed to diffuse into the chitosan hydrogel from a coagulation bath containing sodium caseinate and sodium hydroxide (NaOH). The latter route, where caseinate was incorporated in the neutralization bath, produced fibers with better mechanical properties for textile applications than those formed by the chitosan-caseinate mixed collodion route. The latter processing method consists of enriching a pre-formed chitosan hydrogel with caseinate, preserving the structure of the semicrystalline hydrogel without drastically affecting interactions involved in the chitosan self-assembly. Thus, dried fibers, after coagulation in a NaOH/sodium caseinate aqueous bath, exhibited preserved ultimate mechanical properties. The crystallinity ratio of chitosan was not significantly impacted by the presence of caseinate. However, when caseinate was incorporated into the chitosan dope, chitosan-caseinate fibers exhibited lower ultimate mechanical properties, possibly due to a lower entanglement density in the amorphous phase of the chitosan matrix. A standpoint is to optimize the chitosan-caseinate composition ratio and processing route to find a good compromise between the preservation of fiber mechanical properties and appropriate fiber composition for potential application in drug release.

| S-EPMC10855522 | biostudies-literature

Facile Fabrication of Microfluidic Chips for 3D Hydrodynamic Focusing and Wet Spinning of Polymeric Fibers.

Project description:Microfluidic wet spinning has gained increasing interest in recent years as an alternative to conventional wet spinning by offering higher control in fiber morphology and a gateway for the development of multi-material fibers. Conventionally, microfluidic chips used to create such fibers are fabricated by soft lithography, a method that requires both time and investment in necessary cleanroom facilities. Recently, additive manufacturing techniques were investigated for rapid and cost-efficient prototyping. However, these microfluidic devices are not yet matching the resolutions and tolerances offered by soft lithography. Herein, we report a facile and rapid method using selected arrays of hypodermic needles as templates within a silicone elastomer matrix. The produced microfluidic spinnerets display co-axially aligned circular channels. By simulation and flow experiments, we prove that these devices can maintain laminar flow conditions and achieve precise 3D hydrodynamic focusing. The devices were tested with a commercial polyurethane formulation to demonstrate that fibers with desired morphologies can be produced by varying the degree of hydrodynamic focusing. Thanks to the adaptability of this concept to different microfluidic spinneret designs-as well as to its transparency, ease of fabrication, and cost-efficient procedure-this device sets the ground for transferring microfluidic wet spinning towards industrial textile settings.

| S-EPMC7182802 | biostudies-literature

Integrated dynamic wet spinning of core-sheath hydrogel fibers for optical-to-brain/tissue communications.

Project description:Hydrogel optical light-guides have received substantial interest for applications such as deep-tissue biosensors, optogenetic stimulation and photomedicine due to their biocompatibility, (micro)structure control and tissue-like Young's modulus. However, despite recent developments, large-scale fabrication with a continuous synthetic methodology, which could produce core-sheath hydrogel fibers with the desired optical and mechanical properties suitable for deep-tissue applications, has yet to be achieved. In this study, we report a versatile concept of integrated light-triggered dynamic wet spinning capable of continuously producing core-sheath hydrogel optical fibers with tunable fiber diameters, and mechanical and optical propagation properties. Furthermore, this concept also exhibited versatility for various kinds of core-sheath functional fibers. The wet spinning synthetic procedure and fabrication process were optimized with the rational design of the core/sheath material interface compatibility [core = poly(ethylene glycol diacrylate-co-acrylamide); sheath = Ca-alginate], optical transparency, refractive index and spinning solution viscosity. The resulting hydrogel optical fibers exhibited desirable low optical attenuation (0.18 ± 0.01 dB cm-1 with 650 nm laser light), excellent biocompatibility and tissue-like Young's modulus (<2.60 MPa). The optical waveguide hydrogel fibers were successfully employed for deep-tissue cancer therapy and brain optogenetic stimulation, confirming that they could serve as an efficient versatile tool for diverse deep-tissue therapy and brain optogenetic applications.

| S-EPMC8433079 | biostudies-literature

A wet-filtration-zipping approach for fabricating highly electroconductive and auxetic graphene/carbon nanotube hybrid buckypaper.

Project description:A combination of carbon nanotubes (CNT) and graphene in the form of macroscopic hybrid buckypaper (HBP), exhibits a unique set of properties that can be exploited for many emerging applications. Here, we present a simple, inexpensive and scalable approach for the synthesis of highly conductive auxetic graphene/CNT HBP via wet-filtration-zipping and demonstrate the electrical, electrochemical and mechanical performance (tensile, mode I and mode III fracture) of synthesized HBP. An overall increase in electrical conductivity of 247% is observed for HBP (50 wt.% graphene and 50 wt.% CNT) as compared to BP (100 wt.% CNT) due to effective electronic percolation through the graphene and CNT. As a negative electrode for lithium-ion batteries, HBP shows 50% higher gravimetric specific capacity and 89% lower charge transfer resistance relative to BP. The graphene content in the HBP influences the mechanical performance providing an auxetic structure to HBP with large negative Poisson's ratio. The facile green-chemistry approach reported here can be readily applied to any other 1D and 2D materials and solves key challenges associated with existing buckypaper manufacturing methods. The potential of the synthesis method to integrate with current cellulose paper manufacturing technology and its scalability demonstrate the novelty of the work for industrial scale production.

| S-EPMC6093936 | biostudies-literature

Draw-Spinning of Kilometer-Long and Highly Stretchable Polymer Submicrometer Fibers.

Project description:A new method is developed to directly spinning perfectly uniaxial fibers in an ultrafast manner. Besides, this method can tune the fibers' diameter through adjusting processing parameters such as the feeding rate of precursors. Uniaxial nylon 66 fibers prepared via this method show superior mechanical properties due to the alignment in each level of the structure.

| S-EPMC5604378 | biostudies-literature

Optimization of Dry-Jet Wet Spinning of Regenerated Cellulose Fibers Using [mTBDH][OAc] as a Solvent.

Project description:Superbase-based ionic liquids (ILs) have demonstrated excellent dissolution capability for cellulose, and employing the dry-jet wet spinning process, high-tenacity regenerated textile fibers have been made. Among a range of superbase-based ILs, [mTBDH][OAc] exhibited not only good spinnability but also exceptional recyclability, making it highly suitable for a closed-loop production of regenerated cellulose fibers. To further optimize the spinning process, we investigated the influence of the cellulosic raw materials and the IL with residual water on spinnability and fiber properties. In addition, single-filament spinning and multifilament spinning using spinnerets with different hole densities were investigated to reveal the upscaling challenges of the dry-jet wet spinning process. The air gap conditions, for example, temperature and moisture concentration were simulated using COMSOL multiphysics. The results indicate that the presence of a small amount of water (3 wt%) in the IL has a positive effect on spinnability, while the mechanical properties of the fibers remain unchanged.

| S-EPMC10515369 | biostudies-literature

OmicsDI is part of the ELIXIR infrastructure

OmicsDI is an Elixir interoperability service. Learn more ›

Tweets

OmicsDI Databases

PRIDE
PeptideAtlas
MassIVE
JPOST Repository
Physiome Model Repository

EGA
EVA
ENA
LINCS
PAXDB
Cell Collective

MetaboLights
Metabolomics Workbench
MetabolomeExpress
GNPS
BioModels
FAIRDOMHub

ArrayExpress
dbGaP
ExpressionAtlas
GEO
NODE

Information

Databases
Help
API
Contact us
Code on GitHub
Terms of use
Submit Data