Dataset Information

Towards a High-Power Si@graphite Anode for Lithium Ion Batteries through a Wet Ball Milling Process.

ABSTRACT: Silicon-based anodes are extensively studied as an alternative to graphite for lithium ion batteries. However, silicon particles suffer larges changes in their volume (about 280%) during cycling, which lead to particles cracking and breakage of the solid electrolyte interphase. This process induces continuous irreversible electrolyte decomposition that strongly reduces the battery life. In this research work, different silicon@graphite anodes have been prepared through a facile and scalable ball milling synthesis and have been tested in lithium batteries. The morphology and structure of the different samples have been studied using X-ray diffraction, X-ray photoelectron spectroscopy, Raman spectroscopy, and scanning and transmission electron microscopy. We show how the incorporation of an organic solvent in the synthesis procedure prevents particles agglomeration and leads to a suitable distribution of particles and intimate contact between them. Moreover, the importance of the microstructure of the obtained silicon@graphite electrodes is pointed out. The silicon@graphite anode resulted from the wet ball milling route, which presents capacity values of 850 mA h/g and excellent capacity retention at high current density (?800 mA h/g at 5 A/g).

SUBMITTER: Cabello M

PROVIDER: S-EPMC7321121 | biostudies-literature | 2020 May

REPOSITORIES: biostudies-literature

ACCESS DATA

Publications

Towards a High-Power Si@graphite Anode for Lithium Ion Batteries through a Wet Ball Milling Process.

Cabello Marta M Gucciardi Emanuele E Herrán Alvaro A Carriazo Daniel D Villaverde Aitor A Rojo Teófilo T

Molecules (Basel, Switzerland) 20200527 11

Silicon-based anodes are extensively studied as an alternative to graphite for lithium ion batteries. However, silicon particles suffer larges changes in their volume (about 280%) during cycling, which lead to particles cracking and breakage of the solid electrolyte interphase. This process induces continuous irreversible electrolyte decomposition that strongly reduces the battery life. In this research work, different silicon@graphite anodes have been prepared through a facile and scalable ball ...[more]

PMID: 32471276

Similar Datasets

Project description:Silicon with the properties of high capacity capability, moderate working potential, environmental sensitivity, and existence are the highly promising anode materials for lithium-ion batteries. Silicon anodes have disadvantageous properties and advantages like 300% volume change during lithium insertion and extraction process that can result in capacity fading and a shorter lifetime of the battery. In the literature, different optimizations of Silicon with different nanomaterials or composite materials, in different ratios, and with different binders and different procedures have been studied. The physical mixing of silicon with carbon provides a good performance by combining the high lithium storage capacity of the silicon and the good mechanical and conductive properties of carbon. Binders are one of the other factors affecting the performance of the Si/C anodes. In this study, different ratios of silicon/graphite combinations were tested. The Si/C hybrid material provides an advantageous and efficient use for innovative lithium-ion anodes and available lithium-ion battery technology when the Si/C match performs a suitable combination of two material properties, such as the high lithium storage capacity of silicon and the conductive properties of carbon. This study is aimed to improve the performance of the cell by changing the amount of active material and polymer in the electrode by finding the most appropriate amount of active substance and binder polymer ratio in the electrode. The electrochemical result of the composition, which compensates for the problems caused by the volume expansion of the silicon by using less silicon, showed higher capacitive properties, as it exhibits better adhesion among these compositions with a higher binder ratio. This study resulted in more than 1000 mAh/g specific capacity after 100 cycles at C/3 rate and structural characterization of the samples before and after cycling provided information about the electrode content.

Project description:BackgroundEnzymatic corn wet milling (E-milling) is a process derived from conventional wet milling for the recovery and purification of starch and co-products using proteases to eliminate the need for sulfites and decrease the steeping time. In 2006, the total starch production in USA by conventional wet milling equaled 23 billion kilograms, including modified starches and starches used for sweeteners and ethanol production 1. Process engineering and cost models for an E-milling process have been developed for a processing plant with a capacity of 2.54 million kg of corn per day (100,000 bu/day). These models are based on the previously published models for a traditional wet milling plant with the same capacity. The E-milling process includes grain cleaning, pretreatment, enzymatic treatment, germ separation and recovery, fiber separation and recovery, gluten separation and recovery and starch separation. Information for the development of the conventional models was obtained from a variety of technical sources including commercial wet milling companies, industry experts and equipment suppliers. Additional information for the present models was obtained from our own experience with the development of the E-milling process and trials in the laboratory and at the pilot plant scale. The models were developed using process and cost simulation software (SuperPro Designer) and include processing information such as composition and flow rates of the various process streams, descriptions of the various unit operations and detailed breakdowns of the operating and capital cost of the facility.ResultsBased on the information from the model, we can estimate the cost of production per kilogram of starch using the input prices for corn, enzyme and other wet milling co-products. The work presented here describes the E-milling process and compares the process, the operation and costs with the conventional process.ConclusionThe E-milling process was found to be cost competitive with the conventional process during periods of high corn feedstock costs since the enzymatic process enhances the yields of the products in a corn wet milling process. This model is available upon request from the authors for educational, research and non-commercial uses.

Dataset Information

Towards a High-Power Si@graphite Anode for Lithium Ion Batteries through a Wet Ball Milling Process.

Publications

Towards a High-Power Si@graphite Anode for Lithium Ion Batteries through a Wet Ball Milling Process.

Similar Datasets

OmicsDI is part of the ELIXIR infrastructure

Tweets