Graphene active sensor arrays for long-term and wireless mapping of wide frequency band epicortical brain activity.
Ontology highlight
ABSTRACT:
SUBMITTER: Garcia-Cortadella R
PROVIDER: S-EPMC7801381 | biostudies-literature |
REPOSITORIES: biostudies-literature
Similar Datasets
Project description:In this paper, a novel dual band frequency reconfigurable antenna using an origami magic cube is proposed for wireless sensor network (WSN) applications. The proposed origami antenna consists of a meandered monopole folded onto three sides of the magic cube. A microstrip open-ended stub is loaded on the meandered monopole. The proposed origami magic cube can be mechanically folded and unfolded. The proposed antenna operates at 1.57 GHZ and 2.4 GHz in the folded state. In the unfolded state, the proposed antenna operates at 900 MHz and 2.3 GHz. The resonant frequency of the second band can be tunable by varying the length and position of the open stub. The origami magic cube is built on paper. Its performance is numerically and experimentally demonstrated from S-parameters and radiation patterns. The measured 10 dB impedance bandwidth of the proposed origami antenna is 18% (900-1120 MHz) and 15% (2.1-2.45 GHz) for the unfolded state and 20% (1.3-1.6 GHz) and 14% (2.3-2.5 GHz) for the folded state. The measured peak gain at 900 MHz and 2.3 GHz are 1.1 dBi and 2.32 dBi, respectively, in the unfolded state. The measured peak gain at 1.5 GHz and 2.4 GHz are 3.28 dBi and 1.98 dBi, respectively, in the folded state.
| S-EPMC5712905 | biostudies-literature
Project description:We propose a flexible wireless pressure sensor, which uses a graphene/polydimethylsiloxane (GR/PDMS) sponge as the dielectric layer. The sponge is sandwiched between two surfaces of a folded flexible printed circuit with patterned Cu as the antenna and electrode. By adjusting graphene and NH4HCO3 concentrations, a composite with 20% concentration of NH4HCO3 and 2% concentration of graphene as the dielectric layer is obtained, which exhibits high sensitivity (2.2 MHz/kPa), wide operating range (0-500 kPa), rapid response time (~7 ms), low detection limit (5 Pa), and good stability, recoverability, and repeatability. In addition, the sensor is sensitive to finger bending and facial muscle movements for smile and frown, that are transmitted using wireless electromagnetic coupling; therefore, it has potential for a wide range of applications such as intelligent robots, bionic-electronic skin and wearable electronic devices.
| S-EPMC6408520 | biostudies-literature
Project description:Very few materials show large magnetoresistance (MR) under a low magnetic field at room temperature, which causes the barrier to the development of magnetic field sensors for detecting low-level electromagnetic radiation in real- time. Here, a hybrid reduced graphene oxide (rGO)-based magnetic field sensor is produced by in situ deposition of FeCo nanoparticles (NPs) on reduced graphene oxide (rGO). Special quantum magnetoresistance (MR) of the hybrid rGO is observed, which unveils that Abrikosov's quantum model for layered materials can occur in hybrid rGO; meanwhile, the MR value can be tunable by adjusting the particle density of FeCo NPs on rGO nanosheets. Very high MR value up to 21.02 ± 5.74% at 10 kOe at room temperature is achieved, and the average increasing rate of resistance per kOe is up to 0.9282 Ω kOe-1. In this paper, we demonstrate that the hybrid rGO-based magnetic field sensor can be embedded in a wireless system for real-time detection of low-level electromagnetic radiation caused by a working mobile phone. We believe that the two-dimensional nanomaterials with controllable MR can be integrated with a wireless system for the future connected society.
| S-EPMC7770704 | biostudies-literature
Project description:The Internet of Things (IoT)1,2 employs a large number of spatially distributed wireless sensors to monitor physical environments, e.g., temperature, humidity, and air pressure, and has many applications, including environmental monitoring3, health care monitoring4, smart cities5, and precision agriculture. A wireless sensor can collect, analyze, and transmit measurements of its environment1,2. Currently, wireless sensors used in the IoT are predominately based on electronic devices that may suffer from electromagnetic interference in many circumstances. Being immune to the electromagnetic interference, optical sensors provide a significant advantage in harsh environments6. Furthermore, by introducing optical resonance to enhance light-matter interactions, optical sensors based on resonators exhibit small footprints, extreme sensitivity, and versatile functionalities7,8, which can significantly enhance the capability and flexibility of wireless sensors. Here we provide the first demonstration of a wireless photonic sensor node based on a whispering-gallery-mode (WGM) optical resonator, in which light propagates along the circular rim of such a structure like a sphere, a disk, or a toroid by continuous total internal reflection. The sensor node is controlled via a customized iOS app. Its performance was studied in two practical scenarios: (1) real-time measurement of the air temperature over 12 h and (2) aerial mapping of the temperature distribution using a sensor node mounted on an unmanned drone. Our work demonstrates the capability of WGM optical sensors in practical applications and may pave the way for the large-scale deployment of WGM sensors in the IoT.
| S-EPMC6133935 | biostudies-literature
Project description:Integrated electronic circuitries with pressure sensors have been extensively researched as a key component for emerging electronics applications such as electronic skins and health-monitoring devices. Although existing pressure sensors display high sensitivities, they can only be used for specific purposes due to the narrow range of detectable pressure (under tens of kPa) and the difficulty of forming highly integrated arrays. However, it is essential to develop tactile pressure sensors with a wide pressure range in order to use them for diverse application areas including medical diagnosis, robotics or automotive electronics. Here we report an unconventional approach for fabricating fully integrated active-matrix arrays of pressure-sensitive graphene transistors with air-dielectric layers simply formed by folding two opposing panels. Furthermore, this realizes a wide tactile pressure sensing range from 250 Pa to ∼3 MPa. Additionally, fabrication of pressure sensor arrays and transparent pressure sensors are demonstrated, suggesting their substantial promise as next-generation electronics.
| S-EPMC5381006 | biostudies-literature
Project description:Through harvesting energy by wireless charging and delivering data by wireless communication, this study proposes the concept of a wireless sensor enabled by wireless power (WPWS) and reports the fabrication of a prototype for functional tests. One WPWS node consists of wireless power module and sensor module with different chip-type sensors. Its main feature is the dual antenna structure. Following RFID system architecture, a power harvesting antenna was designed to gather power from a standard reader working in the 915 MHz band. Referring to the Modbus protocol, the other wireless communication antenna was integrated on a node to send sensor data in parallel. The dual antenna structure integrates both the advantages of an RFID system and a wireless sensor. Using a standard UHF RFID reader, WPWS can be enabled in a distributed area with a diameter up to 4 m. Working status is similar to that of a passive tag, except that a tag can only be queried statically, while the WPWS can send dynamic data from the sensors. The function is the same as a wireless sensor node. Different WPWSs equipped with temperature and humidity, optical and airflow velocity sensors are tested in this study. All sensors can send back detection data within 8 s. The accuracy is within 8% deviation compared with laboratory equipment. A wireless sensor network enabled by wireless power should be a totally wireless sensor network using WPWS. However, distributed WPWSs only can form a star topology, the simplest topology for constructing a sensor network. Because of shielding effects, it is difficult to apply other complex topologies. Despite this limitation, WPWS still can be used to extend sensor network applications in hazardous environments. Further research is needed to improve WPWS to realize a totally wireless sensor network.
| S-EPMC3571774 | biostudies-literature
Project description:In situ sensing with wireless digital-data transfer is a potential processing scheme that works very closely to the location of an event monitored by a sensor and converts the sensor's raw output into digitized and informative small-volume bits, as suggested by recent proposals for edge computing and the Internet of Things (IoT). Colour perception may be a target of in situ sensor data acquisition; however, in contrast to from other sensing devices, colour sensors that detect visible light signals are usually located away from light-emitting sources, collecting light transmitting through the space and attenuating it in some manner. For example, in a vacuum chamber whose gas pressure is much less than the ambient atmosphere in which the sensors usually work, there are many veiled light sources, such as discharge plasma, for various industrial purposes including nanoscale manufacturing. In this study, we designed an in-vacuum colour sensor that can work with analogue-to-digital conversion and transfer data by wireless communication; this sensor is active in a low-pressure plasma chamber, detecting light signals and transferring them to a personal computer located outside the vacuum chamber. In addition to detecting lights with controlled spectra from outside successfully, we achieved complete operation of our in-vacuum active sensor for plasma emissions generated at 100 Pa. Comparing the signals with data from simultaneous monitoring by a monochromator, we established that the recorded signals arose from the plasma, confirming successful direct detection of low-pressure plasma emissions without any filtering effects between the sensor and the target object.
| S-EPMC7809036 | biostudies-literature
Project description:The flexible radio frequency (RF) wireless antennas used as sensors, which can detect signal variation resulting from the deformation of the antenna, have attracted increasing attention with the development of wearable electronic devices and the Internet of Things (IoT). However, miniaturization and sensitivity issues restrict the development of flexible RF sensors. In this work, we demonstrate the application of a flexible and highly conductive graphene-assembled film (GAF) for antenna design. The GAF with a high conductivity of 106 S/m has the advantages of light weight, high flexibility, and superb mechanical stability. As a result, a small-size (50 mm × 50 mm) and flexible GAF-based antenna operating at 3.13-4.42 GHz is achieved, and this GAF antenna-based wireless wearable sensor shows high strain sensitivities of 34.9 for tensile bending and 35.6 for compressive bending. Furthermore, this sensor exhibits good mechanical flexibility and structural stability after a 100-cycle bending test when attached to the back of the hand and the wrist, which demonstrates broad application prospects in health-monitoring devices, electronic skins, and smart robotics.
| S-EPMC7288573 | biostudies-literature
Project description:Comprehensive whole-genome structural variation detection is challenging with current approaches. With diploid cells as DNA source and the presence of numerous repetitive elements, short-read DNA sequencing cannot be used to detect structural variation efficiently. In this report, we show that genome mapping with long, fluorescently labeled DNA molecules imaged on nanochannel arrays can be used for whole-genome structural variation detection without sequencing. While whole-genome haplotyping is not achieved, local phasing (across >150-kb regions) is routine, as molecules from the parental chromosomes are examined separately. In one experiment, we generated genome maps from a trio from the 1000 Genomes Project, compared the maps against that derived from the reference human genome, and identified structural variations that are >5 kb in size. We find that these individuals have many more structural variants than those published, including some with the potential of disrupting gene function or regulation.
| S-EPMC4701098 | biostudies-literature
Project description:Antibodies are of importance for the field of proteomics, both as reagents for imaging cells, tissues, and organs and as capturing agents for affinity enrichment in mass-spectrometry-based techniques. It is important to gain basic insights regarding the binding sites (epitopes) of antibodies and potential cross-reactivity to nontarget proteins. Knowledge about an antibody's linear epitopes is also useful in, for instance, developing assays involving the capture of peptides obtained from trypsin cleavage of samples prior to mass spectrometry analysis. Here, we describe, for the first time, the design and use of peptide arrays covering all human proteins for the analysis of antibody specificity, based on parallel in situ photolithic synthesis of a total of 2.1 million overlapping peptides. This has allowed analysis of on- and off-target binding of both monoclonal and polyclonal antibodies, complemented with precise mapping of epitopes based on full amino acid substitution scans. The analysis suggests that linear epitopes are relatively short, confined to five to seven residues, resulting in apparent off-target binding to peptides corresponding to a large number of unrelated human proteins. However, subsequent analysis using recombinant proteins suggests that these linear epitopes have a strict conformational component, thus giving us new insights regarding how antibodies bind to their antigens.
| S-EPMC4047477 | biostudies-literature