Measurement of Neuropeptide Y Using Aptamer-Modified Microelectrodes by Electrochemical Impedance Spectroscopy.
Ontology highlight
ABSTRACT:
SUBMITTER: Lopez L
PROVIDER: S-EPMC7856015 | biostudies-literature |
REPOSITORIES: biostudies-literature
Similar Datasets
Project description:Electrochemical aptamer-based (EAB) sensors are capable of measuring the concentrations of specific molecules in vivo, in real time, and with a few-second time resolution. For their signal transduction mechanism, these sensors utilize a binding-induced conformational change in their target-recognizing, redox-reporter-modified aptamer to alter the rate of electron transfer between the reporter and the supporting electrode. While a variety of voltammetric techniques have been used to monitor this change in kinetics, they suffer from various drawbacks, including time resolution limited to several seconds and sensor-to-sensor variation that requires calibration to remove. Here, however, we show that the use of fast Fourier transform electrochemical impedance spectroscopy (FFT-EIS) to interrogate EAB sensors leads to improved (here better than 2 s) time resolution and calibration-free operation, even when such sensors are deployed in vivo. To showcase these benefits, we demonstrate the approach's ability to perform real-time molecular measurements in the veins of living rats.
| S-EPMC10463274 | biostudies-literature
Project description:Improving the performance of desalination membranes requires better measurements of salt permeability in the polyamide separating layer to elucidate the thermodynamic and kinetic components of membrane permselectivity. In this work, electrochemical impedance spectroscopy (EIS) is introduced as a technique to measure the salt permeability and estimate the salt partition coefficient in thin polyamide films created using molecular layer-by-layer deposition. The impedance of supported polyamide films ranging in thickness from 3.5 nm to 28.5 nm were measured in different electrolyte solutions. Impedance spectra were modeled with equivalent circuits containing resistive and capacitive elements associated with the EIS measurement system as well as characteristic low-frequency parallel resistive and capacitive elements that are associated with the polyamide film. The characteristic polyamide membrane resistance increases with film thickness, decreases with solution concentration, and is an order of magnitude greater for a divalent cationic solution than for a monovalent cationic solution. For each polyamide film, salt permeability is calculated from the membrane resistance, and a salt partition coefficient is estimated. At the highest solution concentration measured, which is representative of brackish water desalination conditions, the calculated salt permeabilities range from P s = 1.3 × 10-16 m s-1 to 3.9 × 10-16 m s-1, and the estimated salt partition coefficients range from K s = 0.008 to 0.016. These measurements demonstrate that EIS is a powerful tool for studying membrane permselectivity through the measurement of salt permeability in thin polyamide films.
| S-EPMC6774373 | biostudies-literature
Project description:The electrical conductivity (EC) of soil is generally measured after soil extraction, so this method cannot represent the in situ EC of soil (e.g., EC of soils with different moisture contents) and therefore lacks comparability in some cases. Using a resistance measurement apparatus converted from a configuration of soil microbial fuel cell, the in situ soil EC was evaluated according to the Ohmic resistance (Rs) measured using electrochemical impedance spectroscopy. The EC of soils with moisture content from 9.1% to 37.5% was calculated according to Rs. A significant positive correlation (R² = 0.896, p < 0.01) between the soil EC and the moisture content was observed, which demonstrated the feasibility of the approach. This new method can not only represent the actual soil EC, but also does not need any pretreatment. Thus it may be used widely in the measurement of the EC for soils and sediments.
| S-EPMC4883316 | biostudies-literature
Project description:We propose monochromatic dark-field imaging microscopy (DFM) to measure the non-faradaic electrochemical impedance spectroscopy (EIS) of single Au nanorods (AuNRs). DFM was utilized to monitor the plasmonic scattering of monochromatic incident light by surface-immobilized individual AuNRs. When modulating the surface potential at a certain frequency, non-faradaic charging and discharging of AuNRs altered their electron density, leading to periodical fluctuations in the scattering intensity. Analysis of the amplitude and phase of the optical intensity fluctuation as a function of modulation frequency resulted in the EIS of single AuNRs. High-frequency (>100 Hz) modulation allowed us to differentiate the intrinsic charging effect from other contributions such as the periodic migration and accumulation of counterions in the surrounding medium, because the latter occurred at a longer timescale. As a result, single nanoparticle EIS led to the surface capacitance of single AuNRs being closer to the theoretical value. Since interfacial capacitance has been proven sensitive to molecular interactions, the present work also offers a new platform for single nanoparticle sensing by measuring the single nanoparticle capacitance.
| S-EPMC5956977 | biostudies-literature
Project description:The underlying sensing mechanism of single-cell-based integrated microelectrode array (IMA) biosensors was investigated via experimental and modeling studies. IMA chips were microfabricated and single-cell-level manipulation was achieved through surface chemistry modification of IMA chips. Individual fibroblast cells (NIH3T3) were immobilized on either lysine-arginine-glycine-aspartic acid (KRGD) short peptide-modified or fibronectin extracellular-cell-adhesion-molecule-modified microelectrodes to record the impedance variations of cell-electrode heterostructure over a frequency range of 1-10 kHz. By fitting experimental data to an application-specific single-cell-level equivalent circuit model, important sensing parameters, including specific cell membrane capacity, cell membrane resistivity, and averaged cell-to-substrate separation, were determined. It was demonstrated that biofunctionalization of planar microelectrode surface by covalently linking short peptides or fibronectin molecules could achieve strong or tight cell adhesion (with an estimated averaged cell-to-substrate separation distance of 11-16 nm), which, in turn, improves the transduced electrical signal from IMA chips. Analyses on frequency-dependent characteristics of single-cell-covered microelectrode impedance and of IMA sensor circuitry response have revealed an addressable frequency band wherein electrical properties of single cells can be distinctively determined and monitored for cellular biosensing applications. The presented work addresses some major limitations in single-cell-based biosensing schemes, i.e., the manipulation of a single cell, the transduction of weak biological signals, and the implementation of a proper model for data analysis, and demonstrates the potential of IMA devices as single-cell biosensors.
| S-EPMC2862283 | biostudies-literature
Project description:A graphene and poly (3,4-ethylenedioxythiophene):poly(styrenesulfonate) (PEDOT:PSS) modified conductive paper-based electrochemical impedance spectroscopy (EIS) aptasensor has been successfully fabricated by a simple and continuous coating process. A graphene/PEDOT:PSS modified paper electrode forms the nanocomposite providing a conductive and sensitive substrate for further aptamer functionalization of the biosensor. This low-cost paper-based aptasensor exhibits its sensitivity to carcinoembryonic antigens (CEA) in standard buffer solutions and human serum samples in a linear range of 0.77-14 ng·mL-1. The limit of detection (LOD) is found to be 0.45 ng·mL-1 and 1.06 ng·mL-1 for CEA in both samples, separately. This aptamer-based sensing device was also evaluated and received a good correlation with the immunoassay detection method. The proposed paper-based aptasensor has demonstrated its potential as a rapid simple point-of-care analytical platform for early cancer diagnosis in less developed areas where manufacturing facilities, analytical instruments, and trained specialists are limited.
| S-EPMC7085636 | biostudies-literature
Project description:Understanding the internal structure of composite nanofluids is critical for controlling their properties and engineering advanced composite nanofluid systems for various applications. This goal can be made possible by precise analysis with the help of a systematic robust platform. Here, we demonstrate a microfluidic device that can control the orientation of carbon nanomaterials in a suspension by applying external fields and subsequently examine the electrochemical properties of the fluids at microscale. Composite nanofluids were prepared using carbon nanomaterials, and their rheological, thermal, electrical, and morphological characteristics were examined. The analysis revealed that microfluidic electrochemical impedance spectroscopy (EIS) in the device offered more reliable in-depth information regarding the change in the microstructure of carbon composite nanofluids than typical bulk measurements. Equivalent circuit modelling was performed based on the EIS results. Furthermore, the hydrodynamics and electrostatics of the microfluidic platform were numerically investigated. We anticipate that this microfluidic approach can serve as a new strategy for designing and analyzing composite nanofluids more efficiently.
| S-EPMC5429664 | biostudies-literature
Project description:Despite advances in diagnosis and therapy, atherosclerotic cardiovascular disease remains the leading cause of morbidity and mortality in the Western world. Predicting metabolically active atherosclerotic lesions has remained an unmet clinical need. We hereby developed an electrochemical strategy to characterize the inflammatory states of high-risk atherosclerotic plaques. Using the concentric bipolar microelectrodes, we sought to demonstrate distinct Electrochemical Impedance Spectroscopic (EIS) measurements for unstable atherosclerotic plaques that harbored active lipids and inflammatory cells. Using equivalent circuits to simulate vessel impedance at the electrode-endoluminal tissue interface, we demonstrated specific electric elements to model working and counter electrode interfaces as well as the tissue impedance. Using explants of human coronary, carotid, and femoral arteries at various Stary stages of atherosclerotic lesions (n=15), we performed endoluminal EIS measurements (n=147) and validated with histology and immunohistochemistry. We computed the vascular tissue resistance using the equivalent circuit model and normalized the resistance to the lesion-free regions. Tissue resistance was significantly elevated in the oxLDL-rich thin-cap atheromas (1.57±0.40, n=14, p<0.001) and fatty streaks (1.36±0.28, n=33, p<0.001) as compared with lesion-free region (1.00±0.18, n=82) or oxLDL-absent fibrous atheromas (0.86±0.30, n=12). Tissue resistance was also elevated in the calcified core of fibrous atheroma (2.37±0.60, n=6, p<0.001). Despite presence of fibrous structures, tissue resistance between ox-LDL-absent fibroatheroma and the lesion-free regions was statistically insignificant (0.86±0.30, n=12, p>0.05). Hence, we demonstrate that the application of EIS strategy was sensitive to detect fibrous cap oxLDL-rich lesions and specific to distinguish oxLDL-absent fibroatheroma.
| S-EPMC3210389 | biostudies-literature
Project description:Combining specific recognition capabilities with the excellent spatiotemporal resolution of small electrodes represents a promising methodology in bioanalytical and chemical sensing. In this paper, we report the development of reproducible electrochemical, aptamer-based (E-AB) sensors on a gold microelectrode platform. Specifically, we develop microscale sensors (25 μm diameter) for two representative small molecule targets-adenosine triphosphate and tobramycin. Furthermore, we report on the challenges encountered at this size scale including small-magnitude signals and interference from the irreversible reduction of dissolved oxygen and present methods to circumvent these challenges. Through the electrochemical deposition of dendritic gold nanostructures, we demonstrate microscale sensors with improved performance by increasing signal-to-noise and consequently sensitivity. Finally, we report on the use of the nonspecific adsorption of serum proteins as an additional layer of surface passivation for stable sensor performance. The sensor development here represents general guidelines for fabricating electrochemical, folding aptamer-based sensors on small-scale electrodes.
| S-EPMC4238692 | biostudies-literature
Project description:The global pandemic caused by severe acute respiratory syndrome coronavirus 2 (SARS-CoV-2) caused a threat to public health and a worldwide crisis. This raised the need for quick, effective, and sensitive detection tools to prevent the rapid transmission rate of the infection. Therefore, this study aimed to develop an electrochemical impedance spectroscopy (EIS)-based aptasensor employing an interdigitated gold electrode (IDE) to detect SARS-CoV-2 Spike (S) glycoprotein and viral particles. This allowed us to sensitively detect SARS-CoV-2 S glycoprotein with a limit of detection (LOD) of 0.4 pg/mL in a buffer solution and to obtain a linear increase for concentrations between 0.2 to 0.8 pg/mL with high specificity. The proposed aptasensor also showed a good sensitivity towards the heat-inactivated SARS-CoV-2 variants in a buffer solution, where the Delta, Wuhan, and Alpha variants were captured at a viral titer of 6.45 ± 0.16 × 103 TCID50/mL, 6.20 × 104 TCID50/mL, and 5.32 ± 0.13 × 102 TCID50/mL, respectively. Furthermore, the detection of SARS-CoV-2 performed in a spiked human nasal fluid provided an LOD of 6.45 ± 0.16 × 103 TCID50/mL for the Delta variant in a 50 µL sample and a detection time of less than 25 min. Atomic force microscopy images complemented the EIS results in this study, revealing that the surface roughness of the IDE after each modification step increased, which indicates that the target was successfully captured. This label-free EIS-based aptasensor has promising potential for the rapid detection of SARS-CoV-2 in complex clinical samples.
| S-EPMC9656073 | biostudies-literature