Browse
Submit Data
Databases
API
Help

Dataset Information

23 Views

0 Connections

0 Citations

0 Reanalyses

0 Downloads

Omics score: 0

High Light Outcoupling Efficiency from Periodically Corrugated OLEDs.

ABSTRACT: Organic light-emitting diodes (OLEDs) suffer from poor light outcoupling efficiency (η_out < 20%) due to large internal waveguiding in the high-index layers/substrate, and plasmonic losses at the metal cathode interface. A promising approach to enhance light outcoupling is to utilize internal periodic corrugations that can diffract waveguided and plasmonic modes back to the air cone. Although corrugations can strongly diffract trapped modes, the optimal geometry of corrugations and limits to η_out are not well-established. We develop a general rigorous scattering matrix theory for light emission from corrugated OLEDs, by solving Maxwell's equations in Fourier space, incorporating the environment-induced modification of the optical emission rate (Purcell effect). We computationally obtain the spectrally emissive power inside and outside the OLED. We find conformally corrugated OLEDs, where all OLED interfaces are conformal with a photonic crystal substrate, having triangular lattice symmetry, exhibit high light outcoupling η_out ∼60-65%, and an enhancement factor exceeding 3 for optimal pitch values between 1 and 2.5 μm. Waveguided and surface plasmon modes are strongly diffracted to the air cone through first-order diffraction. η_out is insensitive to corrugation heights larger than 100 nm. There is a gradual roll-off in η_out for a larger pitch and sharper decreases for small pitch values. Plasmonic losses remain below 10% for all corrugation pitch values. Our predicted OLED designs provide a pathway for achieving very high light outcoupling over the full optical spectrum that can advance organic optoelectronic science and solid-state lighting.

SUBMITTER: Zhang Y

PROVIDER: S-EPMC8028165 | biostudies-literature |

REPOSITORIES: biostudies-literature

ACCESS DATA

Json Xml

Similar Datasets

Anisotropic nanocrystal superlattices overcoming intrinsic light outcoupling efficiency limit in perovskite quantum dot light-emitting diodes.

Project description:Quantum dot (QD) light-emitting diodes (LEDs) are emerging as one of the most promising candidates for next-generation displays. However, their intrinsic light outcoupling efficiency remains considerably lower than the organic counterpart, because it is not yet possible to control the transition-dipole-moment (TDM) orientation in QD solids at device level. Here, using the colloidal lead halide perovskite anisotropic nanocrystals (ANCs) as a model system, we report a directed self-assembly approach to form the anisotropic nanocrystal superlattices (ANSLs). Emission polarization in individual ANCs rescales the radiation from horizontal and vertical transition dipoles, effectively resulting in preferentially horizontal TDM orientation. Based on the emissive thin films comprised of ANSLs, we demonstrate an enhanced ratio of horizontal dipole up to 0.75, enhancing the theoretical light outcoupling efficiency of greater than 30%. Our optimized single-junction QD LEDs showed peak external quantum efficiency of up to 24.96%, comparable to state-of-the-art organic LEDs.

| S-EPMC9018755 | biostudies-literature

Naphtalimide-Based Bipolar Derivatives Enabling High-Efficiency OLEDs.

Project description:Organic light-emitting diodes (OLEDs) have revolutionized the world of technology, making significant contributions to enhancing our everyday lives. With their exceptional display and lighting capabilities, OLEDs have become indispensable in various industries such as smartphones, tablets, televisions, and automotives. They have emerged as a dominant technology, inspiring continuous advancements, and improvements. Taking inspiration from the remarkable advancements in OLED advancements, we have successfully developed naphtalimide-based compounds, namely RB-08, RB-09, RB-10, and RB-11. These compounds exhibit desirable characteristics such as a wide bandgap, high decomposition temperatures (306-366 °C), and very high glass transition temperatures (133-179 °C). Leveraging these exceptional properties, we have harnessed these compounds as green emitters in the aforementioned devices. Among the various fabricated OLEDs, the one incorporating the RB-11 emitter has exhibited superior performance. This specific configuration achieved maximum power efficacy of 7.7 lm/W, current efficacy of 7.9 cd/A, and external quantum efficiency of 3.3%. These results highlight the outstanding capabilities of our synthesized emitter and its potential for further advancements in the field.

| S-EPMC10458866 | biostudies-literature

High-efficiency and low efficiency roll-off near-infrared fluorescent OLEDs through triplet fusion.

Project description:Though urgently needed, high-performance near-infrared organic light-emitting diodes (NIR-OLEDs) are still rare. NIR-OLEDs based on conventional NIR fluorescent materials usually suffer from low external quantum efficiencies (EQEs) because of the intrinsic obstacles according to the spin-statistics limit and energy-gap law. Herein, we realized high-efficiency and low efficiency roll-off fluorescent NIR-OLEDs through efficient triplet fusion of a bipolar host doped with a special naphthoselenadiazole emitter (4,9-bis(4-(2,2-diphenylvinyl)phenyl)-naphtho[2,3-c][1,2,5]selenadiazole, NSeD). Unlike typical NIR organic donor-acceptor (D-A) chromophores, NSeD features a non-D-A structure and a very large HOMO/LUMO overlap and displays a strong deep-red to NIR fluorescence and unique ambipolar character. The corresponding photoluminescence quantum efficiency of NSeD reaches 52% in solution and retains 17% in the blend film. The optimized NIR-OLEDs demonstrated a strong emission at 700 nm, a high maximum EQE of 2.1% (vs. the predicted theoretical maximum efficiency of 1.3%) and the EQE remained at around 2% over a wide range of current densities from 18 to 200 mA cm-2, which is amongst the highest performance for NIR-OLEDs based on organic fluorescent materials.

| S-EPMC6054030 | biostudies-literature

High light-quality OLEDs with a wet-processed single emissive layer.

Project description:High light-quality and low color temperature are crucial to justify a comfortable healthy illumination. Wet-process enables electronic devices cost-effective fabrication feasibility. We present herein low color temperature, blue-emission hazards free organic light emitting diodes (OLEDs) with very-high light-quality indices, that with a single emissive layer spin-coated with multiple blackbody-radiation complementary dyes, namely deep-red, yellow, green and sky-blue. Specifically, an OLED with a 1,854 K color temperature showed a color rendering index (CRI) of 90 and a spectrum resemblance index (SRI) of 88, whose melatonin suppression sensitivity is only 3% relative to a reference blue light of 480 nm. Its maximum retina permissible exposure limit is 3,454 seconds at 100 lx, 11, 10 and 6 times longer and safer than the counterparts of compact fluorescent lamp (5,920 K), light emitting diode (5,500 K) and OLED (5,000 K). By incorporating a co-host, tris(4-carbazoyl-9-ylphenyl)amine (TCTA), the resulting OLED showed a current efficiency of 24.9 cd/A and an external quantum efficiency of 24.5% at 100 cd/m2. It exhibited ultra-high light quality with a CRI of 93 and an SRI of 92. These prove blue-hazard free, high quality and healthy OLED to be fabrication feasible via the easy-to-apply wet-processed single emissive layer with multiple emitters.

| S-EPMC5940822 | biostudies-literature

Single-step holographic fabrication of large-area periodically corrugated metal films.

Project description:We have developed a simple, high-throughput, and cost-effective method to fabricate one-dimensional and two-dimensional periodically corrugated silver films over centimeter scale areas. This fabrication uses a single-step holographic patterning technique with laser intensities as low as 88.8 mW/cm(2) to deposit silver nanoparticles directly from solution to create gratings with periodicities of 570 nm. A dip in the transmission spectrum for these samples is observed due to certain visible wavelengths coupling to surface plasmon polaritons (SPPs) and the peak wavelength of this dip has a linear relationship with the surrounding material's refractive index (RI) with a sensitivity of 553.4 nm/RIU. The figure of merit (the ratio of refractive index sensitivity to the full width at half maximum (FWHM)) is typically in the range of 12-23. Our technique enables single-step fabrication of uniform, sub-wavelength periodic metal structures over a large area with low cost. Such sub-wavelength periodic metal structures are promising candidates as disposable sensors in applications such as affordable environmental monitoring systems and point-of-care diagnostics.

| S-EPMC3528713 | biostudies-other

Enhanced light extraction efficiency and viewing angle characteristics of microcavity OLEDs by using a diffusion layer.

Project description:The viewing angle characteristics and light extraction efficiency of organic light-emitting diodes (OLEDs) with a micro-cavity structure were enhanced. This was accomplished by inserting a diffusion layer composed of nano-sized structures of a transparent polymer poly(methyl methacrylate) (PMMA) combined with a zinc oxide (ZnO) semi-planarization layer with a high refractive index (n = 2.1) into the devices. The PMMA nanostructures were fabricated by employing a reactive ion etching (RIE) process. The height and density of the PMMA nanostructures were controlled by varying the speed at which the PMMA was spin-coated onto the substrate. The insertion of the diffusion layer into the micro-cavity OLEDs (MC-OLEDs) improved the external quantum efficiency (EQE) by as much as 17% when compared to that of a MC-OLED without a diffusion layer. Furthermore, adjustment of the viewing angle from 0° to 60° halved the peak shift distance of the electroluminescence (EL) spectra from 42 to 20 nm. Additionally, changing the viewing angle from 0° to 60° changed the color coordinate movement distance of the MC-OLED with the diffusion layer to 0.078, less than half of the distance of the MC-OLED without the diffusion layer (0.165).

| S-EPMC7873264 | biostudies-literature

Emission Spectral Stability Modification of Tandem Organic Light-Emitting Diodes through Controlling Charge-Carrier Migration and Outcoupling Efficiency at Intermediate/Emitting Unit Interface.

Project description:An intermediate unit (IMU) of tandem organic light-emitting diode (TOLED) can affect the emission spectral stability because of the different charge-carrier migration and outcoupling efficiency at intermediate/emitting unit interface. In this work, an IMU consisting of carbon 60 and copper(II) phthalocyanine, inserted between red-emitting unit and blue-emitting unit, were constructed and fabricated. We focus on the effect of the relative location of the red-emitting unit and blue-emitting unit in the device configuration on the emission spectral stability of TOLED. In the color-tunable TOLED, a maximum current efficiency of 20.4 cd/A, along with light-emitting spectra tuning from red emission at (0.63, 0.31) according to Commission Internationale de L'Eclairage coordinates at a bias of 10 V to white emission at (0.34, 0.27) at 22 V, is realized. Meanwhile, in the color-stable TOLED, a maximum current efficiency of 15.5 cd/A and a stable white emission at (0.31, 0.27) in a wide range of biases from 12 to 22 V are also obtained. This work might inspire a promising approach for the fabrication of color-tunable and color-stable OLEDs for both information display and solid-state lighting.

| S-EPMC6641352 | biostudies-literature

Insight into the mechanism and outcoupling enhancement of excimer-associated white light generation.

Project description:Fundamental insight into excimer formation has been gained by using 9,10-bis[4-(9-carbazolyl)phenyl]anthracene] (Cz9PhAn) as a probe. Cz9PhAn exhibits a highly emissive blue fluorescence in solution and is found to emit a panchromatic white light spectrum (400-750 nm) in film, powder and single crystal, in which an additional excimer band appears at ∼550 nm. Detailed structural analyses, emission relaxation dynamics and a theoretical approach conclude the formation of an anthracene*/phenyl ring excimer through an overlap between π* (anthracene) and π (phenyl ring) orbitals in a face-to-edge stacking orientation. The rate of excimer formation is determined to be 2.2 × 109 s-1 at room temperature, which requires coupling with lattice motion with an activation energy of 0.44 kcal mol-1. Exploiting Cz9PhAn as a single emitter, a fluorescent white organic light emitting diode (WOLED) is fabricated with a maximum external quantum efficiency (ηext) of 3.6% at 1000 cd m-2 (4.2 V) and Commission Internationale de L'Eclairage (CIE) coordinates of (0.30, 0.33). The white-light Cz9PhAn reveals a preferred orientation of the transition dipole moment in the emitting layer to enhance light outcoupling. This non-doped, single component (Cz9PhAn) WOLED greatly reduces the complexity of the fabrication process, rendering a green and cost-effective alternative among the contemporary display/lighting technologies.

| S-EPMC6007176 | biostudies-literature

Phenothiazinen-Dimesitylarylborane-Based Thermally Activated Delayed Fluorescence: High-Performance Non-doped OLEDs With Reduced Efficiency Roll-Off at High Luminescence.

Project description:We report a phenothiazinen-dimesitylarylborane thermally activated delayed fluorescence (TADF) molecule that exhibits high external quantum efficiency (EQE) in non-doped organic light-emitting diodes (OLEDs) at high luminescence. The non-doped device shows green electroluminescence with an emission peak of 540 nm and a maximum EQE of 19.66% obtained at a luminescence of ~170 cd m-2. The EQE is still as high as 17.31% at a high luminescence of 1,500 cd m-2 with small efficiency roll-off.

| S-EPMC6548864 | biostudies-literature

High-Efficiency Visible Light Manipulation Using Dielectric Metasurfaces.

Project description:The development of a miniaturised device that provides efficient beam manipulation with high transmittance is extremely desirable for the broad range of applications including holography, metalens, and imaging. Recently, the potential of dielectric metasurfaces has been unleashed to efficiently manipulate the beam with full 2π-phase control by overlapping the electric and magnetic dipole resonances. However, in the visible range for available materials, it comes with the price of higher absorption that reduces efficiency. Here, we have considered dielectric amorphous silicon (a-Si) nanodisk and engineered them in such a way which provides minimal absorption loss in the visible range. We have experimentally demonstrated meta-deflector with high transmittance which operates in the visible wavelengths. The supercell of proposed meta-deflector consists of 15 amorphous silicon nanodisks numerically shows the transmission efficiency of 95% and deflection efficiency of 95% at operating wavelength of 715 nm. However, experimentally measured transmission and deflection efficiencies are 83% and 71%, respectively, having the experimental deflection angle of 8.40°. Nevertheless, by reducing the supercell length, the deflection angle can be controlled, and the value 15.50° was experimentally achieved using eight disks supercell. Our results suggest a new way to realise the highly transmittance metadevice with full 2π-phase control operating with the visible light which could be applicable in the imaging, metalens, holography, and display applications.

| S-EPMC6482137 | biostudies-literature

OmicsDI is part of the ELIXIR infrastructure

OmicsDI is an Elixir interoperability service. Learn more ›

Tweets

OmicsDI Databases

PRIDE
PeptideAtlas
MassIVE
JPOST Repository
Physiome Model Repository

EGA
EVA
ENA
LINCS
PAXDB
Cell Collective

MetaboLights
Metabolomics Workbench
MetabolomeExpress
GNPS
BioModels
FAIRDOMHub

ArrayExpress
dbGaP
ExpressionAtlas
GEO
NODE

Information

Databases
Help
API
Contact us
Code on GitHub
Terms of use
Submit Data