Potentially toxic metal(loid) distribution and migration in the bottom weathering profile of indigenous zinc smelting slag pile in clastic rock region.
Ontology highlight
ABSTRACT: Background
There are contaminated by potentially toxic metal(loid)s (PTMs) that the surface soil and the weathering profiles around the indigenous zinc smelting slag piles or smelters in the smelting area. However, few systematic studies are currently focusing on the PTM distribution and migration among the slag and its bottom weathering profile.Methods
This research determined the concentrations of PTMs and pH values. And we analyzed PTM distribution in the two weathering profiles (slag-covered and slag-absent) with a small horizontal distance in the clastic rock region in the smelting area.Results
The soil As and Pb contents, respectively, within the 30 and 50 cm depth in the slag-covered section were higher than those in the slag-absent profile. All soil Cd and Zn contents of the slag-covered core were significantly higher than those in the slag-absent weathering section.Conclusions
Compared with the slag-absent weathering section, some PTMs (i.e., As, Cd, Pb and Zn) in the bottom weathering profile were polluted by these elements in the covered slag in the clastic rock region, and their depths were influenced by the slag to varying degrees. Additionally, with time, some PTMs (especially Cd and Zn) of the slag might finally contaminate the groundwater by leaching and infiltration through its bottom weathering profile in the clastic rock region.
SUBMITTER: Peng Y
PROVIDER: S-EPMC8035896 | biostudies-literature |
REPOSITORIES: biostudies-literature
Similar Datasets
Project description:Toxic metalliferous mine-tailings pose a significant health risk to ecosystems and neighboring communities from wind and water dispersion of particulates containing high concentrations of toxic metal(loid)s (e.g., Pb, As, Zn). Tailings are particularly vulnerable to erosion before vegetative cover can be reestablished, i.e., decades or longer in semi-arid environments without intervention. Metal(loid) speciation, linked directly to bioaccessibility and lability, is controlled by mineral weathering and is a key consideration when assessing human and environmental health risks associated with mine sites. At the semi-arid Iron King Mine and Humboldt Smelter Superfund site in central Arizona, the mineral assemblage of the top 2 m of tailings has been previously characterized. A distinct redox gradient was observed in the top 0.5 m of the tailings and the mineral assemblage indicates progressive transformation of ferrous iron sulfides to ferrihydrite and gypsum, which, in turn weather to form schwertmannite and then jarosite accompanied by a progressive decrease in pH (7.3 to 2.3). Within the geochemical context of this reaction front, we examined enriched toxic metal(loid)s As, Pb, and Zn with surficial concentrations 41.1, 10.7, 39.3 mM kg-1 (3080, 2200, and 2570 mg kg-1), respectively. The highest bulk concentrations of As and Zn occur at the redox boundary representing a 1.7 and 4.2 fold enrichment relative to surficial concentrations, respectively, indicating the translocation of toxic elements from the gossan zone to either the underlying redox boundary or the surface crust. Metal speciation was also examined as a function of depth using X-ray absorption spectroscopy (XAS). The deepest sample (180 cm) contains sulfides (e.g., pyrite, arsenopyrite, galena, and sphalerite). Samples from the redox transition zone (25-54 cm) contain a mixture of sulfides, carbonates (siderite, ankerite, cerrusite, and smithsonite) and metal(loid)s sorbed to neoformed secondary Fe phases, principally ferrihydrite. In surface samples (0-35 cm), metal(loid)s are found as sorbed species or incorporated into secondary Fe hydroxysulfate phases, such as schwertmannite and jarosites. Metal-bearing efflorescent salts (e.g., ZnSO4·nH2O) were detected in the surficial sample. Taken together, these data suggest the bioaccessibility and lability of metal(loid)s are altered by mineral weathering, which results in both the downward migration of metal(loid)s to the redox boundary, as well as the precipitation of metal salts at the surface.
| S-EPMC4632981 | biostudies-other
Project description:Copper is a nonferrous metal closely connected to humans. Approximately 40% of copper is produced by reclaimed copper smelting (RCS). Reclaimed copper smelting fly ash and smelting slag are generated during the RCS process, posing a serious threat to the ecosystem and environment as they contain many heavy metals, such as Cu and Zn. In this study, the metal mobility and toxicity of RCS fly ash and smelting slag were analyzed using standard leaching toxicity procedures, sequential extraction procedures, and bioavailability tests. The results showed that the main phases of RCS fly ash were Cu2(OH)3Cl, FeCl2·2H2O, CuS2, C, CuO, Cu, Ca2SiO4, ZnClO42, Zn(OH)2·0.5H2O, and KFeCl3, and those for smelting slag were SiO2, CaCO3, SiS2, CaAl2Si2O8·4H2O, Cu4O3, CuO, ZnO, NiSO4·6H2O, AlPO4, and Na3Mn(PO4)(CO)3. These two slags contain high contents of Cu, Zn and Fe and trace amounts of heavy metals, such as Ba, Be, Cd, Cr, Ni, As, Pb, Au, Se and Sb. RCS fly ash is classified as hazardous waste in both China and the USA as the toxic leaching concentrations of Pb and Cd exceed the thresholds of 5 and 1 mg L-1. Cu and Zn contained in these two slags can easily be released into the environment, although the residual fraction of Cu and Zn was found to be higher than 65%. Additionally, RCS fly ash and smelting slag also show significant biohazardous potential as the EDTA- and DTPA-extractable Zn, Cu and Se of these two residues are considerably high. The results described above could provide reclaimed copper smelting companies and governments with a better understanding of the risk of RCS fly ash and smelting slag, urging them to stop the slag from harming ecosystems and humans.
| S-EPMC8694897 | biostudies-literature
Project description:Indigenous zinc smelting (IZS) is a backward technique that releases a great deal of heavy metal(loid)s into the environment. However, the contamination of heavy metal(loid)s in ground dust and the associated health risks in such areas are poorly known. In this study, a former IZS area in Guizhou, China, was surveyed during 2008-2018 with 15 elements (Ag, As, Bi, Cd, Co, Cr, Cu, Hg, In, Ni, Pb, Sb, Sn, Tl, Zn) being analyzed. The results indicate that most elements (e.g., Ag, As, Cd, Cu, Pb, Sb, Sn, Zn) in ground dust decreased significantly after the cessation of the IZS in 2006; nevertheless, some elements still remained at relatively high levels in 2018, e.g., Pb (average: 762 ± 647 mg/kg), Zn (average: 1287 ± 753 mg/kg), Cd (average: 7.76 ± 5.06 mg/kg), and As (average: 41.9 ± 34.8 mg/kg), indicating they might come from the local contaminated soils, slag residues and smelting potteries. In terms of the impacts on human health, children have both higher non-carcinogenic and carcinogenic risks than that of adults, with the latter subpopulation having a lower risk than the threshold values. Pb and As were the two elements with the highest non-carcinogenic risk for children, the hazard index of local children was still higher than the threshold of 1 (e.g., 1.43 for As, 2.09 for Pb) in 2018. The carcinogenic risk of As exposure to children dropped more than two times to 6.42 × 10-7 in 2018, which falls below the tolerable range (10-6-10-4). This study revealed that although the concentration of heavy metal(loid)s in ground dust and linked health risk in the IZS area has reduced dramatically after the cessation of IZS, continued removal of slag residues and smelting potteries is necessary for further decreasing the human health risk.
| S-EPMC7864351 | biostudies-literature
Project description:Environmental contamination from legacy mine-waste deposits is a persistent problem due to the long history of hard-rock mining. Sulfide ore deposits can contain elevated levels of toxic metal(loid)s that, when mobilized by weathering upon O2 and H2O infusion, can result in groundwater contamination. Dry-climate and lack of vegetative cover result in near-surface pedogenic processes that produce fine-particulate secondary minerals that can be translocated as geo-dusts leading to ingestion or inhalation exposure in nearby communities. In this study, in vitro bioassays were combined with synchrotron-based x-ray spectroscopy and diffraction to determine the potential risk for toxic element release from dust (PM10) samples into biofluid simulants. PM10 were isolated from across the oxidative reaction front in the top meter of tailings subjected to 50 years of weathering under semi-arid climate, and introduced to synthetic gastric- and alveolar-fluids. Aqueous concentrations were measured as a function of reaction time to determine release kinetics. X-ray diffraction and absorption spectroscopy analyses were performed to assess associated changes in mineralogy and elemental speciation. In vitro bioaccessibility of arsenic and lead was highest in less-weathered tailings samples (80-110 cm) and lowest in samples from the sub-oxic transition zone (40-52 cm). Conversely, zinc release to biofluids was greatest in the highly-weathered near-surface tailings. Results indicate that bioaccessibility of As and Pb was controlled by (i) the solubility of Fe2+-bearing solids, (ii) the prevalence of soluble SO4 2-, and (iii) the presence of poorly-crystalline Fe(III) oxide sorbents, whereas Zn bioaccessibility was controlled by the pH-dependent solubility of the stable solid phase.
| S-EPMC6191178 | biostudies-literature
Project description:In this study soils at different depths were collected in a Zn smelting site located in Zhuzhou City, China, in order to understand toxic metal(loid)s distribution and microbial community in vertical soil profile at a smelting site. Except Soil properties and metal(loid)s content, the richness and diversity of microbial communities in soil samples were analyzed via high-throughput Illumina sequencing of 16s rRNA gene amplicons. The results showed that the content of As, Pb, Cu, Cd, Zn, and Mn was relatively high in top soil in comparison to subsoil, while the concentration of Cr in subsoil was comparable with that in top soil due to its relative high background value in this soil layer. The bioavailability of Cd, Mn, Zn, and Pb was relative higher than that of As, Cr, and Cu. The diversity of soil microbial communities decreased with increasing depth, which might be ascribed to the decrease in evenness with increase in depth duo to the influence by environmental conditions, such as pH, TK (total potassium), CEC (cation exchange capacity), ORP (oxidation reduction potential), and Bio-Cu (bioavailable copper). The results also found Acidobacteria, Proteobacteria, Firmicutes, and Chloroflexi were dominant phyla in soil samples. At the genus level, Acinetobacter, Pseudomonas, and Gp7 were dominant soil microorganism. Besides, Environmental factors, such as SOM (soil organic matter), pH, Bio-Cu, Bio-Cd (bioavailable cadmium), and Bio-Pb (bioavailable lead), greatly impacted microbial community in surface soil (1-3 m), while ORP, TK, and AN concentration influenced microbial community in the subsoil (4-10 m).
| S-EPMC7579518 | biostudies-literature
Project description:In this study, Zn/Cu-bearing smelting slag was recycled via an integrated acid dissolution and hematite precipitation method. The slag was dissolved in nitric acid to generate an acid solution containing 23.5?g/L Fe, 4.45?g/L Zn and 2.81?g/L Cu, which was subjected to hydrothermal treatment with the addition of levulinic acid (LA). More than 99.95% of the initial Fe content was removed as hematite particles with diameters of approximately 200?nm, and the residual Fe concentration in the acid was 0.43?mg/L. The generated hematite contained 97.3% Fe2O3, 0.64% ZnO and 0.58% CuO. Greater than 99% of the initial Zn and Cu was retained in the acid and further precipitated as Zn/Cu-bearing solids by adjusting the solution pH to 9. The precipitated Zn/Cu-bearing solids contained 33.6% Zn and 21.7% Cu, whereas the Fe content was less than 0.2%. This paper is the first report of an environmentally friendly approach for recycling smelting slag without generating any hazardous waste.
| S-EPMC7271127 | biostudies-literature
Project description:The improper handling of smelting slag will seriously pollute the environment, and the unfilled roof of the goaf of the mine will threaten the safety of the mine. Expansion materials have attracted more and more attention because of their excellent properties. In this paper, copper-nickel smelting slag that has some active ingredients of gelling is used instead of traditional aggregate and some part of cement in order to reduce its pollution to the environment and its costs. For safety reasons, hydrogen peroxide was chosen as the foaming agent. Sodium silicate and hexadecyl trimethyl ammonium bromide (CTAB) are used as additives. Our results showed that after 28 days of curing, the material has better mechanical properties and the early compressive strength of the material was enhanced by sodium silicate. The efficiency of foaming was improved by CTAB. It also proves that copper-nickel smelting slag can be used in expansion material. At the same time, the utilization rate of the copper-nickel smelting slag of this formula can reach 70%, reduce its pollution to the environment.
| S-EPMC7844011 | biostudies-literature
Project description:Clastic rock aquifer of the coal seam roof often constitutes the direct water-filling aquifer of the coal seam and its water-richness is closely related to the risk of roof water inrush. Therefore, the evaluation of the water-richness of clastic rock aquifer is the basic work of coal seam roof water disaster prevention. This article took the 4th coal seam in Huafeng mine field as an example. It combined the empirical formula method and generalized regression neural network (GRNN) to calculate the development height of water-conducting fracture zone, determined the vertical spatial range of water-richness evaluation. Depth of the sandstone floor, brittle rock ratio, lithological structure index, fault strength index, and fault intersections and endpoints density were selected as the main controlling factors. A combination weighting method based on the analytic hierarchy process (AHP), rough set theory (RS), and minimum deviation method (MD) was proposed to determine the weight of the main controlling factors. Introduced the theory of unascertained measures and confidence recognition criteria to construct an evaluation model for the water-richness of clastic rock aquifers, the study area was divided into three zones: relatively weak water-richness zones, medium water-richness zones, and relatively strong water-richness zones. By comparing with the water inrush points and the water inflow of workfaces, the evaluation model's water yield zoning was consistent with the actual situation, and the prediction effect was good. This provided a new idea for the evaluation of the water-richness of the clastic rock aquifer on the roof of the mining coal seam.
| S-EPMC10948766 | biostudies-literature
Project description:Enhanced rock weathering (ERW) in soils is a promising carbon removal technology, but the realistically achievable efficiency, controlled primarily by in situ weathering rates of the applied rocks, is highly uncertain. Here we explored the impacts of coupled biogeochemical and transport processes and a set of primary environmental and operational controls, using forsterite as a proxy mineral in soils and a multiphase multi-component reactive transport model considering microbe-mediated reactions. For a onetime forsterite application of ~ 16 kg/m2, complete weathering within five years can be achieved, giving an equivalent carbon removal rate of ~ 2.3 kgCO2/m2/yr. However, the rate is highly variable based on site-specific conditions. We showed that the in situ weathering rate can be enhanced by conditions and operations that maintain high CO2 availability via effective transport of atmospheric CO2 (e.g. in well-drained soils) and/or sufficient biogenic CO2 supply (e.g. stimulated plant-microbe processes). Our results further highlight that the effect of increasing surface area on weathering rate can be significant-so that the energy penalty of reducing the grain size may be justified-only when CO2 supply is nonlimiting. Therefore, for ERW practices to be effective, siting and engineering design (e.g. optimal grain size) need to be co-optimized.
| S-EPMC10275906 | biostudies-literature
Project description:In this study, we isolated and characterized rock-weathering bacteria from the surfaces of less and more altered tuffs, along with the adjacent soils, with respect to their rock weathering pattern, stress resistance, community structure, and the changes in these rocks and soils. Using a moderate-nutrition medium, we obtained 150 isolates from the rocks and soils. The rock-weathering patterns of the isolates were characterized using batch cultures that measure the quantity of Si, Al, and Fe released from tuff under aerobic conditions. Based on the potential of the bacterial influence on the element releases, the isolates could be grouped into highly, moderately, and least effective element solubilizers, respectively. Significantly more highly effective Al and Fe solubilizers were observed in the altered rocks, while the soils had more highly effective Si solubilizers. Furthermore, more isolates from the altered rocks significantly acidified the culture medium in the rock weathering process. Dynamic changes in the element release showed the distinct element releasing patterns of three selected isolates. More isolates from the altered rocks could grow at 4 °C or at 55 °C or at pH 4. Some isolates from the altered rocks could grow at pH 10 and with 10-15% (w/v) NaCl. The altered rocks and the soils existed in diverse and different highly weathering-specific culturable rock-weathering community structures. The changes in the culturable weathering communities between the altered rocks and the soils were attributable not only to major bacterial groups but also to a change in the minor population structure.
| S-EPMC9079951 | biostudies-literature