Multifunctional Magnetic Nanocolloids for Hybrid Solar-Thermoelectric Energy Harvesting.
Ontology highlight
ABSTRACT:
SUBMITTER: Sani E
PROVIDER: S-EPMC8074063 | biostudies-literature |
REPOSITORIES: biostudies-literature
Similar Datasets
Project description:Whereas the rigid nature of standard thermoelectrics limits their use, flexible thermoelectric platforms can find much broader applications, for example, in low-power, wearable energy harvesting for internet-of-things applications. Here we realize continuous, flexible thermoelectric threads via a rapid extrusion of 3D-printable composite inks (Bi2Te3 n- or p-type micrograins within a non-conducting polymer as a binder) followed by compression through a roller-pair, and we demonstrate their applications in flexible, low-power energy harvesting. The thermoelectric power factors of these threads are enhanced up to 7 orders-of-magnitude after lateral compression, principally due to improved conductivity resulting from reduced void volume fraction and partial alignment of thermoelectric micrograins. This dependence is quantified using a conductivity/Seebeck vise for pressure-controlled studies. The resulting grain-to-grain conductivity is well explained with a modified percolation theory to model a pressure-dependent conductivity. Flexible thermoelectric modules are demonstrated to utilize thermal gradients either parallel or transverse to the thread direction.
| S-EPMC6897922 | biostudies-literature
Project description:Over the last few years, a growing interest has surfaced about the possibility of enhancing solar harvester efficiency by coupling photovoltaic (PV) cells with thermoelectric generators (TEGs). To be effective solutions, hybrid thermoelectric-photovoltaic (HTEPV) solar harvesters must not only increase the solar conversion efficiency but should also be economically competitive. The aim of this paper is to estimate the profitability of HTEPV solar harvesters with no reference to specific materials, relating it instead to their physical properties only and thus providing a tool to address research effort toward classes of HTEPV systems able to compete with current PV technologies. An economic convenience index is defined and used to assess the economic sustainability of hybridization. It is found that, although hybridization often leads to enhanced solar power conversion, power costs (USD/W) may not always justify HTEPV deployment at the current stage of technology. An analysis of the cost structure shows that profitability requires largely enhanced thermoelectric stages, concentrated solar cells, or PV materials with favorable temperature efficiency coefficients, such as perovskite solar cells.
| S-EPMC8159161 | biostudies-literature
Project description:For any thermoelectric effects to be achieved, a thermoelectric material must have hot and cold sides. Typically, the hot side can be easily obtained by excess heat. However, the passive cooling method is often limited to convective heat transfer to the surroundings. Since thermoelectric voltage is proportional to the temperature difference between the hot and cold sides, efficient passive cooling to increase the temperature gradient is of critical importance. Here, we report simultaneous harvesting of radiative cooling at the top and solar heating at the bottom to enhance the temperature gradient for a transverse thermoelectric effect which generates thermoelectric voltage perpendicular to the temperature gradient. We demonstrate this concept by using the spin Seebeck effect and confirm that the spin Seebeck device shows the highest thermoelectric voltage when both radiative cooling and solar heating are utilized. Furthermore, the device generates thermoelectric voltage even at night through radiative cooling which enables continuous energy harvesting throughout a day. Planar geometry and scalable fabrication process are advantageous for energy harvesting applications.
| S-EPMC8245095 | biostudies-literature
Project description:Photovoltaic-thermoelectric (PV-TE) tandem system has been considered as an effective way to fully utilize the solar spectrum, and has been demonstrated in a perovskite solar cell (PSC)-thermoelectric (TE) configuration. However, the conventional PSC-TE tandem architecture cannot convert infrared light transmitted through the upper PSC into heat effectively, impeding the heat-electricity conversion of TE devices. Herein, a semi-transparent PSC-photothermal-TE tandem system is designed for improved photothermal utilization. Through optimizing the buffer layer of the back transparent electrode, semi-transparent PSC with a power conversion efficiency (PCE) of 13% and an average transmittance of 53% in the range of 800-1500 nm was obtained. On this basis, a photothermal thin film was introduced between the semi-transparent PSC and the TE device, which increased the efficiency contribution ratio of the TE device from 14% to 19%, showing enhanced utilization of AM 1.5 G solar spectrum and improved photo-thermal-electric conversion efficiency.
| S-EPMC11020555 | biostudies-literature
Project description:With accelerating trends in miniaturization of semiconductor devices, techniques for energy harvesting become increasingly important, especially in wearable technologies and sensors for the internet of things. Although thermoelectric systems have many attractive attributes in this context, maintaining large temperature differences across the device terminals and achieving low-thermal impedance interfaces to the surrounding environment become increasingly difficult to achieve as the characteristic dimensions decrease. Here, we propose and demonstrate an architectural solution to this problem, where thin-film active materials integrate into compliant, open three-dimensional (3D) forms. This approach not only enables efficient thermal impedance matching but also multiplies the heat flow through the harvester, thereby increasing the efficiencies for power conversion. Interconnected arrays of 3D thermoelectric coils built using microscale ribbons of monocrystalline silicon as the active material demonstrate these concepts. Quantitative measurements and simulations establish the basic operating principles and the key design features. The results suggest a scalable strategy for deploying hard thermoelectric thin-film materials in harvesters that can integrate effectively with soft materials systems, including those of the human body.
| S-EPMC6214638 | biostudies-literature
Project description:Discovering novel multifunctional metamaterials with energy harvesting and sensing functionalities is likely to be the next technological evolution of the metamaterial science. Here, we introduce a novel concept called self-aware composite mechanical metamaterial (SCMM) that can transform mechanical metamaterials into nanogenerators and active sensing mediums. In pursuit of this goal, we examine new paradigms where finely tailored and seamlessly integrated self-recovering snapping microstructures composed of topologically different triboelectric materials can form self-powering and self-sensing meta-tribomaterial systems. We explore various deformation mechanisms required to induce contact electrification between these snapping microstructures under periodic deformations. The multifunctional meta-tribomaterial systems created under the SCMM concept will act as triboelectric nanogenerators capable of generating electrical signals in response to the applied mechanical excitations. The generated electrical signal can be used for active sensing of the applied force and can be stored for empowering sensors and embedded electronics. We conduct theoretical and experimental studies to understand the mechanical and electrical behavior of the multifunctional SCMM systems. The broad application of the proposed SCMM concept for designing artificial materials with novel properties and functionalities is highlighted via prototyping self-powering and self-sensing blood vessel stents and shock absorbers.
| S-EPMC8423374 | biostudies-literature
Project description:Progress has been developed in harvesting low-frequency and irregular blue energy using a triboelectric-electromagnetic hybrid generator in recent years. However, the design of the high-efficiency, mechanically durable hybrid structure is still challenging. In this study, we report a fully packaged triboelectric-electromagnetic hybrid generator (TEHG), in which magnets were utilized as the trigger to drive contact-separation-mode triboelectric nanogenerators (CS-TENGs) and coupled with copper coils to operate rotary freestanding-mode electromagnetic generators (RF-EMGs). The magnet pairs that produce attraction were used to transfer the external mechanical energy to the CS-TENGs, and packaging of the CS-TENG part was achieved to protect it from the ambient environment. Under a rotatory speed of 100 rpm, the CS-TENGs enabled the TEHG to deliver an output voltage, current, and average power of 315.8 V, 44.6 μA, and ~ 90.7 μW, and the output of the RF-EMGs was 0.59 V, 1.78 mA, and 79.6 μW, respectively. The cylinder-like structure made the TEHG more easily driven by water flow and demonstrated to work as a practical power source to charge commercial capacitors. It can charge a 33 μF capacitor from 0 to 2.1 V in 84 s, and the stored energy in the capacitor can drive an electronic thermometer and form a self-powered water-temperature sensing system.
| S-EPMC6199107 | biostudies-literature
Project description:As crystalline silicon solar cells approach in efficiency their theoretical limit, strategies are being developed to achieve efficient infrared energy harvesting to augment silicon using solar photons from beyond its 1100?nm absorption edge. Herein we report a strategy that uses multi-bandgap lead sulfide colloidal quantum dot (CQD) ensembles to maximize short-circuit current and open-circuit voltage simultaneously. We engineer the density of states to achieve simultaneously a large quasi-Fermi level splitting and a tailored optical response that matches the infrared solar spectrum. We shape the density of states by selectively introducing larger-bandgap CQDs within a smaller-bandgap CQD population, achieving a 40?meV increase in open-circuit voltage. The near-unity internal quantum efficiency in the optimized multi-bandgap CQD ensemble yielded a maximized photocurrent of 3.7?±?0.2?mA?cm-2. This provides a record for silicon-filtered power conversion efficiency equal to one power point, a 25% (relative) improvement compared to the best previously-reported results.
| S-EPMC6167381 | biostudies-literature
Project description:This comprehensive review analysis examines the domain of composite thermoelectric materials that integrate nanoparticles, providing a critical assessment of their methods for improving thermoelectric properties and the procedures used for their fabrication. This study examines several approaches to enhance power factor and lattice thermal conductivity, emphasizing the influence of secondary phases and structural alterations. This study investigates the impact of synthesis methods on the electrical characteristics of materials, with a particular focus on novel techniques such as electrodeposition onto carbon nanotubes. The acquired insights provide useful guidance for the creation of new thermoelectric materials. The review also compares and contrasts organic and inorganic thermoelectric materials, with a particular focus on the potential of inorganic materials in the context of waste heat recovery and power production within industries. This analysis highlights the role of inorganic materials in improving energy efficiency and promoting environmental sustainability.
| S-EPMC10938428 | biostudies-literature
Project description:Thermoelectric (TE) composites, with photocured resin as the matrix and Ag2Se (AS) as the filler, are synthesized by a digital-light-processing (DLP) based 3D printer. The mixture of diurethane dimethacrylate (DUDMA) and isobornyl acrylate (IBOA) is used as a UV-curable resin because of their low viscosity and high miscibility. Scanning electron microscopy (FE-SEM) images confirm that the filler retains its shape and remains after the UV-curing process. After completing curing, the mechanical and thermoelectric properties of the composite with different AS contents were measured. The addition of the AS filler increases the thermoelectric properties of the cured resin. When the AS contents increase by 30 wt.%, the maximum power factor was obtained (~ 51.5 μW/m·K2 at room temperature). Additionally, due to the phonon scattering effect between the interfaces, the thermal conductivity of composite is lower than that of pristine photoresin. The maximum thermoelectric figure of merit (ZT) is ~ 0.12, which is achieved with 30 wt.% of AS at 300 K with the enhanced power factor and reduced thermal conductivity. This study presents a novel manufacturing method for a thermoelectric composite using 3D printing.
| S-EPMC8371107 | biostudies-literature